clean up code

git-svn-id: https://rt-thread.googlecode.com/svn/trunk@940 bbd45198-f89e-11dd-88c7-29a3b14d5316

libcpu/arm/s3c24x0/config.inc

@@ -1,852 +0,0 @@
-;/*****************************************************************************/
-;/* S3C2440.S: Startup file for Samsung S3C440                                */
-;/*****************************************************************************/
-;/* <<< Use Configuration Wizard in Context Menu >>>                          */
-;/*****************************************************************************/
-;/* This file is part of the uVision/ARM development tools.                   */
-;/* Copyright (c) 2005-2008 Keil Software. All rights reserved.               */
-;/* This software may only be used under the terms of a valid, current,       */
-;/* end user licence from KEIL for a compatible version of KEIL software      */
-;/* development tools. Nothing else gives you the right to use this software. */
-;/*****************************************************************************/
-
-
-;/*
-; *  The S3C2440.S code is executed after CPU Reset. This file may be
-; *  translated with the following SET symbols. In uVision these SET
-; *  symbols are entered under Options - ASM - Define.
-; *
-; *  NO_CLOCK_SETUP: when set the startup code will not initialize Clock
-; *  (used mostly when clock is already initialized from script .ini
-; *  file).
-; *
-; *  NO_MC_SETUP: when set the startup code will not initialize Memory
-; *  Controller (used mostly when clock is already initialized from script
-; *  .ini file).
-; *
-; *  NO_GP_SETUP: when set the startup code will not initialize General Ports
-; *  (used mostly when clock is already initialized from script .ini
-; *  file).
-; *
-; *  RAM_INTVEC: when set the startup code copies exception vectors
-; *  from execution address to on-chip RAM.
-; */
-
-
-; Standard definitions of Mode bits and Interrupt (I & F) flags in PSRs
-
-Mode_USR        EQU     0x10
-Mode_FIQ        EQU     0x11
-Mode_IRQ        EQU     0x12
-Mode_SVC        EQU     0x13
-Mode_ABT        EQU     0x17
-Mode_UND        EQU     0x1B
-Mode_SYS        EQU     0x1F
-
-I_Bit           EQU     0x80            ; when I bit is set, IRQ is disabled
-F_Bit           EQU     0x40            ; when F bit is set, FIQ is disabled
-
-FLASH_BASE_ADDR EQU	0x00
-;----------------------- Stack and Heap Definitions ----------------------------
-
-;// <h> Stack Configuration (Stack Sizes in Bytes)
-;//   <o0> Undefined Mode      <0x0-0xFFFFFFFF:8>
-;//   <o1> Supervisor Mode     <0x0-0xFFFFFFFF:8>
-;//   <o2> Abort Mode          <0x0-0xFFFFFFFF:8>
-;//   <o3> Fast Interrupt Mode <0x0-0xFFFFFFFF:8>
-;//   <o4> Interrupt Mode      <0x0-0xFFFFFFFF:8>
-;//   <o5> User/System Mode    <0x0-0xFFFFFFFF:8>
-;// </h>
-
-UND_Stack_Size  EQU     0x00000000
-SVC_Stack_Size  EQU     0x00000100
-ABT_Stack_Size  EQU     0x00000000
-FIQ_Stack_Size  EQU     0x00000000
-IRQ_Stack_Size  EQU     0x00000100
-USR_Stack_Size  EQU     0x00000100
-
-ISR_Stack_Size  EQU     (UND_Stack_Size + SVC_Stack_Size + ABT_Stack_Size + \
-                         FIQ_Stack_Size + IRQ_Stack_Size)
-
-                AREA    STACK, NOINIT, READWRITE, ALIGN=3
-
-Stack_Mem       SPACE   USR_Stack_Size
-__initial_sp    SPACE   ISR_Stack_Size
-Stack_Top
-
-
-;// <h> Heap Configuration
-;//   <o>  Heap Size (in Bytes) <0x0-0xFFFFFFFF>
-;// </h>
-
-Heap_Size       EQU     0x00000000
-
-                AREA    HEAP, NOINIT, READWRITE, ALIGN=3
-__heap_base
-Heap_Mem        SPACE   Heap_Size
-__heap_limit
-
-
-;----------------------- Memory Definitions ------------------------------------
-
-; Internal Memory Base Addresses
-IRAM_BASE       EQU     0x40000000
-
-
-;----------------------- Watchdog Timer Definitions ----------------------------
-
-WT_BASE         EQU     0x53000000      ; Watchdog Timer Base Address
-WTCON_OFS       EQU     0x00            ; Watchdog Timer Control Register Offset
-WTDAT_OFS       EQU     0x04            ; Watchdog Timer Data Register    Offset
-WTCNT_OFS       EQU     0x08            ; Watchdog Timer Count Register   Offset
-
-;// <e> Watchdog Timer Setup
-;//   <h> Watchdog Timer Control Register (WTCON)
-;//     <o1.8..15>  Prescaler Value <0-255>
-;//     <o1.5>      Watchdog Timer Enable
-;//     <o1.3..4>   Clock Division Factor
-;//       <0=> 16   <1=> 32  <2=> 64  <3=> 128
-;//     <o1.2>      Interrupt Generation Enable
-;//     <o1.0>      Reset Enable
-;//   </h>
-;//   <h> Watchdog Timer Data Register (WTDAT)
-;//     <o2.0..15>  Count Reload Value <0-65535>
-;//   </h>
-;// </e> Watchdog Timer Setup
-WT_SETUP        EQU     1
-WTCON_Val       EQU     0x00000000
-WTDAT_Val       EQU     0x00008000
-
-
-;----------------------- Clock and Power Management Definitions ----------------
-
-CLOCK_BASE      EQU     0x4C000000      ; Clock Base Address
-LOCKTIME_OFS    EQU     0x00            ; PLL Lock Time Count Register   Offset
-MPLLCON_OFS     EQU     0x04            ; MPLL Configuration Register    Offset
-UPLLCON_OFS     EQU     0x08            ; UPLL Configuration Register    Offset
-CLKCON_OFS      EQU     0x0C            ; Clock Generator Control Reg    Offset
-CLKSLOW_OFS     EQU     0x10            ; Clock Slow Control Register    Offset
-CLKDIVN_OFS     EQU     0x14            ; Clock Divider Control Register Offset
-CAMDIVN_OFS     EQU     0x18            ; Camera Clock Divider Register  Offset
-
-;// <e> Clock Setup
-;//   <h> PLL Lock Time Count Register (LOCKTIME)
-;//     <o1.16..31> U_LTIME: UPLL Lock Time Count Value for UCLK <0x0-0xFFFF>
-;//     <o1.0..15>  M_LTIME: MPLL Lock Time Count Value for FCLK, HCLK and PCLK <0x0-0xFFFF>
-;//   </h>
-;//   <h> MPLL Configuration Register (MPLLCON)
-;//     <i> MPLL = (2 * m * Fin) / (p * 2^s)
-;//     <o2.12..19> m: Main Divider m Value <9-256><#-8>
-;//       <i> m = MDIV + 8
-;//     <o2.4..9>   p: Pre-divider p Value <3-64><#-2>
-;//       <i> p = PDIV + 2
-;//     <o2.0..1>   s: Post Divider s Value <0-3>
-;//       <i> s = SDIV
-;//   </h>
-;//   <h> UPLL Configuration Register (UPLLCON)
-;//     <i> UPLL = ( m * Fin) / (p * 2^s)
-;//     <o3.12..19> m: Main Divider m Value <8-263><#-8>
-;//       <i> m = MDIV + 8
-;//     <o3.4..9>   p: Pre-divider p Value <2-65><#-2>
-;//       <i> p = PDIV + 2
-;//     <o3.0..1>   s: Post Divider s Value <0-3>
-;//       <i> s = SDIV
-;//   </h>
-;//   <h> Clock Generation Control Register (CLKCON)
-;//     <o4.20>     AC97 Enable
-;//     <o4.19>     Camera Enable
-;//     <o4.18>     SPI Enable
-;//     <o4.17>     IIS Enable
-;//     <o4.16>     IIC Enable
-;//     <o4.15>     ADC + Touch Screen Enable
-;//     <o4.14>     RTC Enable
-;//     <o4.13>     GPIO Enable
-;//     <o4.12>     UART2 Enable
-;//     <o4.11>     UART1 Enable
-;//     <o4.10>     UART0 Enable
-;//     <o4.9>      SDI Enable
-;//     <o4.8>      PWMTIMER Enable
-;//     <o4.7>      USB Device Enable
-;//     <o4.6>      USB Host Enable
-;//     <o4.5>      LCDC Enable
-;//     <o4.4>      NAND FLASH Controller Enable
-;//     <o4.3>      SLEEP Enable
-;//     <o4.2>      IDLE BIT Enable
-;//   </h>
-;//   <h> Clock Slow Control Register (CLKSLOW)
-;//     <o5.7>      UCLK_ON: UCLK ON
-;//     <o5.5>      MPLL_OFF: Turn off PLL
-;//     <o5.4>      SLOW_BIT: Slow Mode Enable
-;//     <o5.0..2>   SLOW_VAL: Slow Clock Divider <0-7>
-;//   </h>
-;//   <h> Clock Divider Control Register (CLKDIVN)
-;//     <o6.3>      DIVN_UPLL: UCLK Select
-;//       <0=> UCLK = UPLL clock
-;//       <1=> UCLK = UPLL clock / 2
-;//     <o6.1..2>   HDIVN: HCLK Select
-;//       <0=> HCLK = FCLK
-;//       <1=> HCLK = FCLK / 2
-;//       <2=> HCLK = FCLK / 4 if HCLK4_HALF = 0 in CAMDIVN, else HCLK = FCLK / 8
-;//       <3=> HCLK = FCLK / 3 if HCLK3_HALF = 0 in CAMDIVN, else HCLK = FCLK / 6
-;//     <o6.0>      PDIVN: PCLK Select
-;//       <0=> PCLK = HCLK
-;//       <1=> PCLK = HCLK / 2
-;//   </h>
-;//   <h> Camera Clock Divider Control Register (CAMDIVN)
-;//     <o7.12>     DVS_EN: ARM Core Clock Select
-;//       <0=> ARM core runs at FCLK
-;//       <1=> ARM core runs at HCLK
-;//     <o7.9>      HCLK4_HALF: HDIVN Division Rate Change Bit
-;//       <0=> If HDIVN = 2 in CLKDIVN then HCLK = FCLK / 4
-;//       <1=> If HDIVN = 2 in CLKDIVN then HCLK = FCLK / 8
-;//     <o7.8>      HCLK3_HALF: HDIVN Division Rate Change Bit
-;//       <0=> If HDIVN = 3 in CLKDIVN then HCLK = FCLK / 3
-;//       <1=> If HDIVN = 3 in CLKDIVN then HCLK = FCLK / 6
-;//     <o7.4>      CAMCLK Select
-;//       <0=> CAMCLK = UPLL
-;//       <1=> CAMCLK = UPLL / CAMCLK_DIV
-;//     <o7.0..3>   CAMCLK_DIV: CAMCLK Divider <0-15>
-;//       <i> Camera Clock = UPLL / (2 * (CAMCLK_DIV + 1))
-;//       <i> Divider is used only if CAMCLK_SEL = 1
-;//   </h>
-;// </e> Clock Setup
-CLOCK_SETUP     EQU     1
-LOCKTIME_Val    EQU     0x0FFF0FFF
-MPLLCON_Val     EQU     0x00043011
-UPLLCON_Val     EQU     0x00038021
-CLKCON_Val      EQU     0x001FFFF0
-CLKSLOW_Val     EQU     0x00000004
-CLKDIVN_Val     EQU     0x0000000F
-CAMDIVN_Val     EQU     0x00000000
-
-
-;----------------------- Memory Controller Definitions -------------------------
-
-MC_BASE         EQU     0x48000000      ; Memory Controller Base Address
-BWSCON_OFS      EQU     0x00            ; Bus Width and Wait Status Ctrl Offset
-BANKCON0_OFS    EQU     0x04            ; Bank 0 Control Register        Offset
-BANKCON1_OFS    EQU     0x08            ; Bank 1 Control Register        Offset
-BANKCON2_OFS    EQU     0x0C            ; Bank 2 Control Register        Offset
-BANKCON3_OFS    EQU     0x10            ; Bank 3 Control Register        Offset
-BANKCON4_OFS    EQU     0x14            ; Bank 4 Control Register        Offset
-BANKCON5_OFS    EQU     0x18            ; Bank 5 Control Register        Offset
-BANKCON6_OFS    EQU     0x1C            ; Bank 6 Control Register        Offset
-BANKCON7_OFS    EQU     0x20            ; Bank 7 Control Register        Offset
-REFRESH_OFS     EQU     0x24            ; SDRAM Refresh Control Register Offset
-BANKSIZE_OFS    EQU     0x28            ; Flexible Bank Size Register    Offset
-MRSRB6_OFS      EQU     0x2C            ; Bank 6 Mode Register           Offset
-MRSRB7_OFS      EQU     0x30            ; Bank 7 Mode Register           Offset
-
-
-;------------------------NAND FLASH----------------------------------------------
-NAND_CTL_BASE	EQU		0x4E000000
-;/* offset */
-oNFCONF			EQU		0x00
-oNFCONT			EQU		0x04
-oNFCMD			EQU		0x08
-oNFADDR			EQU		0x0c
-oNFDATA			EQU		0x10
-oNFSTAT			EQU		0x20
-oNFECC			EQU		0x2c
-
-
-;// <e> Memory Controller Setup
-;//   <h> Bus Width and Wait Control Register (BWSCON)
-;//     <o1.31>     ST7: Use UB/LB for Bank 7
-;//     <o1.30>     WS7: Enable Wait Status for Bank 7
-;//     <o1.28..29> DW7: Data Bus Width for Bank 7
-;//       <0=> 8-bit  <1=> 16-bit  <2=> 32-bit  <3=> Reserved
-;//     <o1.27>     ST6: Use UB/LB for Bank 6
-;//     <o1.26>     WS6: Enable Wait Status for Bank 6
-;//     <o1.24..25> DW6: Data Bus Width for Bank 6
-;//       <0=> 8-bit  <1=> 16-bit  <2=> 32-bit  <3=> Reserved
-;//     <o1.23>     ST5: Use UB/LB for Bank 5
-;//     <o1.22>     WS5: Enable Wait Status for Bank 5
-;//     <o1.20..21> DW5: Data Bus Width for Bank 5
-;//       <0=> 8-bit  <1=> 16-bit  <2=> 32-bit  <3=> Reserved
-;//     <o1.19>     ST4: Use UB/LB for Bank 4
-;//     <o1.18>     WS4: Enable Wait Status for Bank 4
-;//     <o1.16..17> DW4: Data Bus Width for Bank 4
-;//       <0=> 8-bit  <1=> 16-bit  <2=> 32-bit  <3=> Reserved
-;//     <o1.15>     ST3: Use UB/LB for Bank 3
-;//     <o1.14>     WS3: Enable Wait Status for Bank 3
-;//     <o1.12..13> DW3: Data Bus Width for Bank 3
-;//       <0=> 8-bit  <1=> 16-bit  <2=> 32-bit  <3=> Reserved
-;//     <o1.11>     ST2: Use UB/LB for Bank 2
-;//     <o1.10>     WS2: Enable Wait Status for Bank 2
-;//     <o1.8..9>   DW2: Data Bus Width for Bank 2
-;//       <0=> 8-bit  <1=> 16-bit  <2=> 32-bit  <3=> Reserved
-;//     <o1.7>      ST1: Use UB/LB for Bank 1
-;//     <o1.6>      WS1: Enable Wait Status for Bank 1
-;//     <o1.4..5>   DW1: Data Bus Width for Bank 1
-;//       <0=> 8-bit  <1=> 16-bit  <2=> 32-bit  <3=> Reserved
-;//     <o1.1..2>   DW0: Indicate Data Bus Width for Bank 0
-;//       <1=> 16-bit  <2=> 32-bit
-;//   </h>
-;//   <h> Bank 0 Control Register (BANKCON0)
-;//     <o2.13..14> Tacs: Address Set-up Time before nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o2.11..12> Tcos: Chip Selection Set-up Time before nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o2.8..10>  Tacc: Access Cycle
-;//       <0=>  1 clocks  <1=>  2 clocks  <2=>  3 clocks  <3=>  4 clocks
-;//       <4=>  6 clocks  <5=>  8 clocks  <6=> 10 clocks  <7=> 14 clocks
-;//     <o2.6..7>   Tcoh: Chip Selection Hold Time after nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o2.4..5>   Tcah: Address Hold Time after nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o2.2..3>   Tacp: Page Mode Access Cycle at Page Mode
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> 6 clocks
-;//     <o2.0..1>   PMC: Page Mode Configuration
-;//       <0=> normal (1 data)  <1=> 4 data  <2=> 8 data  <3=> 16 data
-;//   </h>
-;//   <h> Bank 1 Control Register (BANKCON1)
-;//     <o3.13..14> Tacs: Address Set-up Time before nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o3.11..12> Tcos: Chip Selection Set-up Time before nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o3.8..10>  Tacc: Access Cycle
-;//       <0=>  1 clocks  <1=>  2 clocks  <2=>  3 clocks  <3=>  4 clocks
-;//       <4=>  6 clocks  <5=>  8 clocks  <6=> 10 clocks  <7=> 14 clocks
-;//     <o3.6..7>   Tcoh: Chip Selection Hold Time after nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o3.4..5>   Tcah: Address Hold Time after nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o3.2..3>   Tacp: Page Mode Access Cycle at Page Mode
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> 6 clocks
-;//     <o3.0..1>   PMC: Page Mode Configuration
-;//       <0=> normal (1 data)  <1=> 4 data  <2=> 8 data  <3=> 16 data
-;//   </h>
-;//   <h> Bank 2 Control Register (BANKCON2)
-;//     <o4.13..14> Tacs: Address Set-up Time before nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o4.11..12> Tcos: Chip Selection Set-up Time before nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o4.8..10>  Tacc: Access Cycle
-;//       <0=>  1 clocks  <1=>  2 clocks  <2=>  3 clocks  <3=>  4 clocks
-;//       <4=>  6 clocks  <5=>  8 clocks  <6=> 10 clocks  <7=> 14 clocks
-;//     <o4.6..7>   Tcoh: Chip Selection Hold Time after nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o4.4..5>   Tcah: Address Hold Time after nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o4.2..3>   Tacp: Page Mode Access Cycle at Page Mode
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> 6 clocks
-;//     <o4.0..1>   PMC: Page Mode Configuration
-;//       <0=> normal (1 data)  <1=> 4 data  <2=> 8 data  <3=> 16 data
-;//   </h>
-;//   <h> Bank 3 Control Register (BANKCON3)
-;//     <o5.13..14> Tacs: Address Set-up Time before nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o5.11..12> Tcos: Chip Selection Set-up Time before nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o5.8..10>  Tacc: Access Cycle
-;//       <0=>  1 clocks  <1=>  2 clocks  <2=>  3 clocks  <3=>  4 clocks
-;//       <4=>  6 clocks  <5=>  8 clocks  <6=> 10 clocks  <7=> 14 clocks
-;//     <o5.6..7>   Tcoh: Chip Selection Hold Time after nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o5.4..5>   Tcah: Address Hold Time after nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o5.2..3>   Tacp: Page Mode Access Cycle at Page Mode
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> 6 clocks
-;//     <o5.0..1>   PMC: Page Mode Configuration
-;//       <0=> normal (1 data)  <1=> 4 data  <2=> 8 data  <3=> 16 data
-;//   </h>
-;//   <h> Bank 4 Control Register (BANKCON4)
-;//     <o6.13..14> Tacs: Address Set-up Time before nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o6.11..12> Tcos: Chip Selection Set-up Time before nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o6.8..10>  Tacc: Access Cycle
-;//       <0=>  1 clocks  <1=>  2 clocks  <2=>  3 clocks  <3=>  4 clocks
-;//       <4=>  6 clocks  <5=>  8 clocks  <6=> 10 clocks  <7=> 14 clocks
-;//     <o6.6..7>   Tcoh: Chip Selection Hold Time after nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o6.4..5>   Tcah: Address Hold Time after nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o6.2..3>   Tacp: Page Mode Access Cycle at Page Mode
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> 6 clocks
-;//     <o6.0..1>   PMC: Page Mode Configuration
-;//       <0=> normal (1 data)  <1=> 4 data  <2=> 8 data  <3=> 16 data
-;//   </h>
-;//   <h> Bank 5 Control Register (BANKCON5)
-;//     <o7.13..14> Tacs: Address Set-up Time before nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o7.11..12> Tcos: Chip Selection Set-up Time before nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o7.8..10>  Tacc: Access Cycle
-;//       <0=>  1 clocks  <1=>  2 clocks  <2=>  3 clocks  <3=>  4 clocks
-;//       <4=>  6 clocks  <5=>  8 clocks  <6=> 10 clocks  <7=> 14 clocks
-;//     <o7.6..7>   Tcoh: Chip Selection Hold Time after nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o7.4..5>   Tcah: Address Hold Time after nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o7.2..3>   Tacp: Page Mode Access Cycle at Page Mode
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> 6 clocks
-;//     <o7.0..1>   PMC: Page Mode Configuration
-;//       <0=> normal (1 data)  <1=> 4 data  <2=> 8 data  <3=> 16 data
-;//   </h>
-;//   <h> Bank 6 Control Register (BANKCON6)
-;//     <o8.15..16> Memory Type Selection
-;//       <0=> ROM or SRAM  <3=> SDRAM
-;//     <o8.13..14> Tacs: Address Set-up Time before nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o8.11..12> Tcos: Chip Selection Set-up Time before nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o8.8..10>  Tacc: Access Cycle
-;//       <0=>  1 clocks  <1=>  2 clocks  <2=>  3 clocks  <3=>  4 clocks
-;//       <4=>  6 clocks  <5=>  8 clocks  <6=> 10 clocks  <7=> 14 clocks
-;//     <o8.6..7>   Tcoh: Chip Selection Hold Time after nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o8.4..5>   Tcah: Address Hold Time after nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o8.2..3>   Tacp/Trcd: Page Mode Access Cycle at Page Mode / RAS to CAS Delay
-;//       <i>  Parameter depends on Memory Type: if type SRAM then parameter is Tacp,
-;//       <i>  if type is SDRAM then parameter is Trcd
-;//       <i>  For SDRAM 6 cycles setting is not allowed
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> 6 clocks
-;//     <o8.0..1>   PMC/SCAN: Page Mode Configuration / Column Address Number <0-3>
-;//       <i>  Parameter depends on Memory Type: if type SRAM then parameter is PMC,
-;//       <i>  if type is SDRAM then parameter is SCAN
-;//   </h>
-;//   <h> Bank 7 Control Register (BANKCON7)
-;//     <o9.15..16> Memory Type Selection
-;//       <0=> ROM or SRAM  <3=> SDRAM
-;//     <o9.13..14> Tacs: Address Set-up Time before nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o9.11..12> Tcos: Chip Selection Set-up Time before nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o9.8..10>  Tacc: Access Cycle
-;//       <0=>  1 clocks  <1=>  2 clocks  <2=>  3 clocks  <3=>  4 clocks
-;//       <4=>  6 clocks  <5=>  8 clocks  <6=> 10 clocks  <7=> 14 clocks
-;//     <o9.6..7>   Tcoh: Chip Selection Hold Time after nOE
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o9.4..5>   Tcah: Address Hold Time after nGCS
-;//       <0=> 0 clocks  <1=> 1 clocks  <2=> 2 clocks  <3=> 4 clocks
-;//     <o9.2..3>   Tacp/Trcd: Page Mode Access Cycle at Page Mode / RAS to CAS Delay
-;//       <i>  Parameter depends on Memory Type: if type SRAM then parameter is Tacp,
-;//       <i>  if type is SDRAM then parameter is Trcd
-;//       <i>  For SDRAM 6 cycles setting is not allowed
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> 6 clocks
-;//     <o9.0..1>   PMC/SCAN: Page Mode Configuration / Column Address Number <0-3>
-;//       <i>  Parameter depends on Memory Type: if type SRAM then parameter is PMC,
-;//       <i>  if type is SDRAM then parameter is SCAN
-;//   </h>
-;//   <h> SDRAM Refresh Control Register (REFRESH)
-;//     <o10.23>    REFEN: SDRAM Refresh Enable
-;//     <o10.22>    TREFMD: SDRAM Refresh Mode
-;//       <0=> CBR/Auto Refresh  <1=> Self Refresh
-;//     <o10.20..21> Trp: SDRAM RAS Pre-charge Time
-;//       <0=> 2 clocks  <1=> 3 clocks  <2=> 4 clocks  <3=> Reserved
-;//     <o10.18..19> Tsrc: SDRAM Semi Row Cycle Time
-;//       <i> SDRAM Row cycle time: Trc = Tsrc + Trp
-;//       <0=> 4 clocks  <1=> 5 clocks  <2=> 6 clocks  <3=> 7 clocks
-;//     <o10.0..10> Refresh Counter <0-1023>
-;//       <i> Refresh Period = (2048 - Refresh Count + 1) / HCLK
-;//   </h>
-;//   <h> Flexible Bank Size Register (BANKSIZE)
-;//     <o11.7>     BURST_EN: ARM Core Burst Operation Enable
-;//     <o11.5>     SCKE_EN: SDRAM Power Down Mode Enable
-;//     <o11.4>     SCLK_EN: SCLK Enabled During SDRAM Access Cycle
-;//       <0=> SCLK is always active  <1=> SCLK is active only during the access
-;//     <o11.0..2>  BK76MAP: BANK6 and BANK7 Memory Map
-;//       <0=> 32MB / 32MB  <1=> 64MB / 64MB  <2=> 128MB / 128MB
-;//       <4=> 2MB / 2MB    <5=> 4MB / 4MB    <6=> 8MB / 8MB      <7=> 16MB / 16MB
-;//     <o11.0..10> Refresh Counter <0-1023>
-;//       <i> Refresh Period = (2048 - Refresh Count + 1) / HCLK
-;//   </h>
-;//   <h> SDRAM Mode Register Set Register 6 (MRSRB6)
-;//     <o12.7>     WBL: Write Burst Length
-;//       <0=> Burst (Fixed)
-;//     <o12.7..8>  TM: Test Mode
-;//       <0=> Mode register set (Fixed)
-;//     <o12.4..6>  CL: CAS Latency
-;//       <0=> 1 clocks  <1=> 2 clocks  <2=> 3 clocks
-;//     <o12.3>     BT: Burst Type
-;//       <0=> Sequential (Fixed)
-;//     <o12.0..2>  BL: Burst Length
-;//       <0=> 1 (Fixed)
-;//   </h>
-;//   <h> SDRAM Mode Register Set Register 7 (MRSRB7)
-;//     <o13.7>     WBL: Write Burst Length
-;//       <0=> Burst (Fixed)
-;//     <o13.7..8>  TM: Test Mode
-;//       <0=> Mode register set (Fixed)
-;//     <o13.4..6>  CL: CAS Latency
-;//       <0=> 1 clocks  <1=> 2 clocks  <2=> 3 clocks
-;//     <o13.3>     BT: Burst Type
-;//       <0=> Sequential (Fixed)
-;//     <o13.0..2>  BL: Burst Length
-;//       <0=> 1 (Fixed)
-;//   </h>
-;// </e> Memory Controller Setup
-MC_SETUP        EQU     1
-BWSCON_Val      EQU     0x22151112
-BANKCON0_Val    EQU     0x00000700
-BANKCON1_Val    EQU     0x00000700
-BANKCON2_Val    EQU     0x00000700
-BANKCON3_Val    EQU     0x00000700
-BANKCON4_Val    EQU     0x00002E50
-BANKCON5_Val    EQU     0x00000700
-BANKCON6_Val    EQU     0x00018005
-BANKCON7_Val    EQU     0x00018005
-REFRESH_Val     EQU     0x008E07A3
-BANKSIZE_Val    EQU     0x000000B2
-MRSRB6_Val      EQU     0x00000030
-MRSRB7_Val      EQU     0x00000030
-
-
-;----------------------- Interrupt Config	 -----------------------------------
-SRCPND   		EQU		0x4a000000    ;Interrupt request status
-INTMOD   		EQU		0x4a000004    ;Interrupt mode control
-INTMSK   		EQU		0x4a000008    ;Interrupt mask control
-PRIORITY 		EQU		0x4a00000c    ;IRQ priority control           <-- May 06, 2002 SOP
-INTPND   		EQU		0x4a000010    ;Interrupt request status
-INTOFFSET		EQU		0x4a000014    ;Interruot request source offset
-SUSSRCPND		EQU		0x4a000018    ;Sub source pending
-INTSUBMSK		EQU		0x4a00001c    ;Interrupt sub mask
-
-;----------------------- I/O Port Definitions ----------------------------------
-
-GPA_BASE        EQU     0x56000000      ; GPA Base Address
-GPB_BASE        EQU     0x56000010      ; GPB Base Address
-GPC_BASE        EQU     0x56000020      ; GPC Base Address
-GPD_BASE        EQU     0x56000030      ; GPD Base Address
-GPE_BASE        EQU     0x56000040      ; GPE Base Address
-GPF_BASE        EQU     0x56000050      ; GPF Base Address
-GPG_BASE        EQU     0x56000060      ; GPG Base Address
-GPH_BASE        EQU     0x56000070      ; GPH Base Address
-GPJ_BASE        EQU     0x560000D0      ; GPJ Base Address
-GPCON_OFS       EQU     0x00            ; Control Register Offset
-GPDAT_OFS       EQU     0x04            ; Data Register Offset
-GPUP_OFS        EQU     0x08            ; Pull-up Disable Register Offset
-
-;// <e> I/O Setup
-GP_SETUP        EQU     0
-
-;//   <e> Port A Settings
-;//     <h> Port A Control Register (GPACON)
-;//         <o1.22>     GPA22     <0=> Output   <1=> nFCE
-;//         <o1.21>     GPA21     <0=> Output   <1=> nRSTOUT
-;//         <o1.20>     GPA20     <0=> Output   <1=> nFRE
-;//         <o1.19>     GPA19     <0=> Output   <1=> nFWE
-;//         <o1.18>     GPA18     <0=> Output   <1=> ALE
-;//         <o1.17>     GPA17     <0=> Output   <1=> CLE
-;//         <o1.16>     GPA16     <0=> Output   <1=> nGCS[5]
-;//         <o1.15>     GPA15     <0=> Output   <1=> nGCS[4]
-;//         <o1.14>     GPA14     <0=> Output   <1=> nGCS[3]
-;//         <o1.13>     GPA13     <0=> Output   <1=> nGCS[2]
-;//         <o1.12>     GPA12     <0=> Output   <1=> nGCS[1]
-;//         <o1.11>     GPA11     <0=> Output   <1=> ADDR26
-;//         <o1.10>     GPA10     <0=> Output   <1=> ADDR25
-;//         <o1.9>      GPA9      <0=> Output   <1=> ADDR24
-;//         <o1.8>      GPA8      <0=> Output   <1=> ADDR23
-;//         <o1.7>      GPA7      <0=> Output   <1=> ADDR22
-;//         <o1.6>      GPA6      <0=> Output   <1=> ADDR21
-;//         <o1.5>      GPA5      <0=> Output   <1=> ADDR20
-;//         <o1.4>      GPA4      <0=> Output   <1=> ADDR19
-;//         <o1.3>      GPA3      <0=> Output   <1=> ADDR18
-;//         <o1.2>      GPA2      <0=> Output   <1=> ADDR17
-;//         <o1.1>      GPA1      <0=> Output   <1=> ADDR16
-;//         <o1.0>      GPA0      <0=> Output   <1=> ADDR0
-;//     </h>
-;//   </e>
-GPA_SETUP       EQU     0
-GPACON_Val      EQU     0x000003FF
-
-;//   <e> Port B Settings
-;//     <h> Port B Control Register (GPBCON)
-;//       <o1.20..21> GPB10     <0=> Input <1=> Output <2=> nXDREQ0 <3=> Reserved
-;//       <o1.18..19> GPB9      <0=> Input <1=> Output <2=> nXDACK0 <3=> Reserved
-;//       <o1.16..17> GPB8      <0=> Input <1=> Output <2=> nXDREQ1 <3=> Reserved
-;//       <o1.14..15> GPB7      <0=> Input <1=> Output <2=> nXDACK1 <3=> Reserved
-;//       <o1.12..13> GPB6      <0=> Input <1=> Output <2=> nXBREQ  <3=> Reserved
-;//       <o1.10..11> GPB5      <0=> Input <1=> Output <2=> nXBACK  <3=> Reserved
-;//       <o1.8..9>   GPB4      <0=> Input <1=> Output <2=> TCLK[0] <3=> Reserved
-;//       <o1.6..7>   GPB3      <0=> Input <1=> Output <2=> TOUT3   <3=> Reserved
-;//       <o1.4..5>   GPB2      <0=> Input <1=> Output <2=> TOUT2   <3=> Reserved
-;//       <o1.2..3>   GPB1      <0=> Input <1=> Output <2=> TOUT1   <3=> Reserved
-;//       <o1.0..1>   GPB0      <0=> Input <1=> Output <2=> TOUT0   <3=> Reserved
-;//     </h>
-;//     <h> Port B Pull-up Settings Register (GPBUP)
-;//       <o2.10>     GPB10 Pull-up Disable
-;//       <o2.9>      GPB9  Pull-up Disable
-;//       <o2.8>      GPB8  Pull-up Disable
-;//       <o2.7>      GPB7  Pull-up Disable
-;//       <o2.6>      GPB6  Pull-up Disable
-;//       <o2.5>      GPB5  Pull-up Disable
-;//       <o2.4>      GPB4  Pull-up Disable
-;//       <o2.3>      GPB3  Pull-up Disable
-;//       <o2.2>      GPB2  Pull-up Disable
-;//       <o2.1>      GPB1  Pull-up Disable
-;//       <o2.0>      GPB0  Pull-up Disable
-;//     </h>
-;//   </e>
-GPB_SETUP       EQU     0
-GPBCON_Val      EQU     0x00000000
-GPBUP_Val       EQU     0x00000000
-
-;//   <e> Port C Settings
-;//     <h> Port C Control Register (GPCCON)
-;//       <o1.30..31> GPC15     <0=> Input <1=> Output <2=> VD[7]   <3=> Reserved
-;//       <o1.28..29> GPC14     <0=> Input <1=> Output <2=> VD[6]   <3=> Reserved
-;//       <o1.26..27> GPC13     <0=> Input <1=> Output <2=> VD[5]   <3=> Reserved
-;//       <o1.24..25> GPC12     <0=> Input <1=> Output <2=> VD[4]   <3=> Reserved
-;//       <o1.22..23> GPC11     <0=> Input <1=> Output <2=> VD[3]   <3=> Reserved
-;//       <o1.20..21> GPC10     <0=> Input <1=> Output <2=> VD[2]   <3=> Reserved
-;//       <o1.18..19> GPC9      <0=> Input <1=> Output <2=> VD[1]   <3=> Reserved
-;//       <o1.16..17> GPC8      <0=> Input <1=> Output <2=> VD[0]   <3=> Reserved
-;//       <o1.14..15> GPC7      <0=> Input <1=> Output <2=> LCD_LPCREVB <3=> Reserved
-;//       <o1.12..13> GPC6      <0=> Input <1=> Output <2=> LCD_LPCREV  <3=> Reserved
-;//       <o1.10..11> GPC5      <0=> Input <1=> Output <2=> LCD_LPCOE   <3=> Reserved
-;//       <o1.8..9>   GPC4      <0=> Input <1=> Output <2=> VM      <3=> I2SSDI
-;//       <o1.6..7>   GPC3      <0=> Input <1=> Output <2=> VFRAME  <3=> Reserved
-;//       <o1.4..5>   GPC2      <0=> Input <1=> Output <2=> VLINE   <3=> Reserved
-;//       <o1.2..3>   GPC1      <0=> Input <1=> Output <2=> VCLK    <3=> Reserved
-;//       <o1.0..1>   GPC0      <0=> Input <1=> Output <2=> LEND    <3=> Reserved
-;//     </h>
-;//     <h> Port C Pull-up Settings Register (GPCUP)
-;//       <o2.15>     GPC15 Pull-up Disable
-;//       <o2.14>     GPC14 Pull-up Disable
-;//       <o2.13>     GPC13 Pull-up Disable
-;//       <o2.12>     GPC12 Pull-up Disable
-;//       <o2.11>     GPC11 Pull-up Disable
-;//       <o2.10>     GPC10 Pull-up Disable
-;//       <o2.9>      GPC9  Pull-up Disable
-;//       <o2.8>      GPC8  Pull-up Disable
-;//       <o2.7>      GPC7  Pull-up Disable
-;//       <o2.6>      GPC6  Pull-up Disable
-;//       <o2.5>      GPC5  Pull-up Disable
-;//       <o2.4>      GPC4  Pull-up Disable
-;//       <o2.3>      GPC3  Pull-up Disable
-;//       <o2.2>      GPC2  Pull-up Disable
-;//       <o2.1>      GPC1  Pull-up Disable
-;//       <o2.0>      GPC0  Pull-up Disable
-;//     </h>
-;//   </e>
-GPC_SETUP       EQU     0
-GPCCON_Val      EQU     0x00000000
-GPCUP_Val       EQU     0x00000000
-
-;//   <e> Port D Settings
-;//     <h> Port D Control Register (GPDCON)
-;//       <o1.30..31> GPD15     <0=> Input <1=> Output <2=> VD[23]  <3=> nSS0
-;//       <o1.28..29> GPD14     <0=> Input <1=> Output <2=> VD[22]  <3=> nSS1
-;//       <o1.26..27> GPD13     <0=> Input <1=> Output <2=> VD[21]  <3=> Reserved
-;//       <o1.24..25> GPD12     <0=> Input <1=> Output <2=> VD[20]  <3=> Reserved
-;//       <o1.22..23> GPD11     <0=> Input <1=> Output <2=> VD[19]  <3=> Reserved
-;//       <o1.20..21> GPD10     <0=> Input <1=> Output <2=> VD[18]  <3=> SPICLK1
-;//       <o1.18..19> GPD9      <0=> Input <1=> Output <2=> VD[17]  <3=> SPIMOSI1
-;//       <o1.16..17> GPD8      <0=> Input <1=> Output <2=> VD[16]  <3=> SPIMISO1
-;//       <o1.14..15> GPD7      <0=> Input <1=> Output <2=> VD[15]  <3=> Reserved
-;//       <o1.12..13> GPD6      <0=> Input <1=> Output <2=> VD[14]  <3=> Reserved
-;//       <o1.10..11> GPD5      <0=> Input <1=> Output <2=> VD[13]  <3=> Reserved
-;//       <o1.8..9>   GPD4      <0=> Input <1=> Output <2=> VD[12]  <3=> Reserved
-;//       <o1.6..7>   GPD3      <0=> Input <1=> Output <2=> VD[11]  <3=> Reserved
-;//       <o1.4..5>   GPD2      <0=> Input <1=> Output <2=> VD[10]  <3=> Reserved
-;//       <o1.2..3>   GPD1      <0=> Input <1=> Output <2=> VD[9]   <3=> Reserved
-;//       <o1.0..1>   GPD0      <0=> Input <1=> Output <2=> VD[8]   <3=> Reserved
-;//     </h>
-;//     <h> Port D Pull-up Settings Register (GPDUP)
-;//       <o2.15>     GPD15 Pull-up Disable
-;//       <o2.14>     GPD14 Pull-up Disable
-;//       <o2.13>     GPD13 Pull-up Disable
-;//       <o2.12>     GPD12 Pull-up Disable
-;//       <o2.11>     GPD11 Pull-up Disable
-;//       <o2.10>     GPD10 Pull-up Disable
-;//       <o2.9>      GPD9  Pull-up Disable
-;//       <o2.8>      GPD8  Pull-up Disable
-;//       <o2.7>      GPD7  Pull-up Disable
-;//       <o2.6>      GPD6  Pull-up Disable
-;//       <o2.5>      GPD5  Pull-up Disable
-;//       <o2.4>      GPD4  Pull-up Disable
-;//       <o2.3>      GPD3  Pull-up Disable
-;//       <o2.2>      GPD2  Pull-up Disable
-;//       <o2.1>      GPD1  Pull-up Disable
-;//       <o2.0>      GPD0  Pull-up Disable
-;//     </h>
-;//   </e>
-GPD_SETUP       EQU     0
-GPDCON_Val      EQU     0x00000000
-GPDUP_Val       EQU     0x00000000
-
-;//   <e> Port E Settings
-;//     <h> Port E Control Register (GPECON)
-;//       <o1.30..31> GPE15     <0=> Input <1=> Output <2=> IICSDA  <3=> Reserved
-;//         <i> This pad is open-drain, and has no pull-up option.
-;//       <o1.28..29> GPE14     <0=> Input <1=> Output <2=> IICSCL  <3=> Reserved
-;//         <i> This pad is open-drain, and has no pull-up option.
-;//       <o1.26..27> GPE13     <0=> Input <1=> Output <2=> SPICLK0 <3=> Reserved
-;//       <o1.24..25> GPE12     <0=> Input <1=> Output <2=> SPIMOSI0 <3=> Reserved
-;//       <o1.22..23> GPE11     <0=> Input <1=> Output <2=> SPIMISO0 <3=> Reserved
-;//       <o1.20..21> GPE10     <0=> Input <1=> Output <2=> SDDAT3  <3=> Reserved
-;//       <o1.18..19> GPE9      <0=> Input <1=> Output <2=> SDDAT2  <3=> Reserved
-;//       <o1.16..17> GPE8      <0=> Input <1=> Output <2=> SDDAT1  <3=> Reserved
-;//       <o1.14..15> GPE7      <0=> Input <1=> Output <2=> SDDAT0  <3=> Reserved
-;//       <o1.12..13> GPE6      <0=> Input <1=> Output <2=> SDCMD   <3=> Reserved
-;//       <o1.10..11> GPE5      <0=> Input <1=> Output <2=> SDCLK   <3=> Reserved
-;//       <o1.8..9>   GPE4      <0=> Input <1=> Output <2=> I2SDO   <3=> AC_SDATA_OUT
-;//       <o1.6..7>   GPE3      <0=> Input <1=> Output <2=> I2SDI   <3=> AC_SDATA_IN
-;//       <o1.4..5>   GPE2      <0=> Input <1=> Output <2=> CDCLK   <3=> AC_nRESET
-;//       <o1.2..3>   GPE1      <0=> Input <1=> Output <2=> I2SSCLK <3=> AC_BIT_CLK
-;//       <o1.0..1>   GPE0      <0=> Input <1=> Output <2=> I2SLRCK <3=> AC_SYNC
-;//     </h>
-;//     <h> Port E Pull-up Settings Register (GPEUP)
-;//       <o2.13>     GPE13 Pull-up Disable
-;//       <o2.12>     GPE12 Pull-up Disable
-;//       <o2.11>     GPE11 Pull-up Disable
-;//       <o2.10>     GPE10 Pull-up Disable
-;//       <o2.9>      GPE9  Pull-up Disable
-;//       <o2.8>      GPE8  Pull-up Disable
-;//       <o2.7>      GPE7  Pull-up Disable
-;//       <o2.6>      GPE6  Pull-up Disable
-;//       <o2.5>      GPE5  Pull-up Disable
-;//       <o2.4>      GPE4  Pull-up Disable
-;//       <o2.3>      GPE3  Pull-up Disable
-;//       <o2.2>      GPE2  Pull-up Disable
-;//       <o2.1>      GPE1  Pull-up Disable
-;//       <o2.0>      GPE0  Pull-up Disable
-;//     </h>
-;//   </e>
-GPE_SETUP       EQU     0
-GPECON_Val      EQU     0x00000000
-GPEUP_Val       EQU     0x00000000
-
-;//   <e> Port F Settings
-;//     <h> Port F Control Register (GPFCON)
-;//       <o1.14..15> GPF7      <0=> Input <1=> Output <2=> EINT[7] <3=> Reserved
-;//       <o1.12..13> GPF6      <0=> Input <1=> Output <2=> EINT[6] <3=> Reserved
-;//       <o1.10..11> GPF5      <0=> Input <1=> Output <2=> EINT[5] <3=> Reserved
-;//       <o1.8..9>   GPF4      <0=> Input <1=> Output <2=> EINT[4] <3=> Reserved
-;//       <o1.6..7>   GPF3      <0=> Input <1=> Output <2=> EINT[3] <3=> Reserved
-;//       <o1.4..5>   GPF2      <0=> Input <1=> Output <2=> EINT[2] <3=> Reserved
-;//       <o1.2..3>   GPF1      <0=> Input <1=> Output <2=> EINT[1] <3=> Reserved
-;//       <o1.0..1>   GPF0      <0=> Input <1=> Output <2=> EINT[0] <3=> Reserved
-;//     </h>
-;//     <h> Port F Pull-up Settings Register (GPFUP)
-;//       <o2.7>      GPF7  Pull-up Disable
-;//       <o2.6>      GPF6  Pull-up Disable
-;//       <o2.5>      GPF5  Pull-up Disable
-;//       <o2.4>      GPF4  Pull-up Disable
-;//       <o2.3>      GPF3  Pull-up Disable
-;//       <o2.2>      GPF2  Pull-up Disable
-;//       <o2.1>      GPF1  Pull-up Disable
-;//       <o2.0>      GPF0  Pull-up Disable
-;//     </h>
-;//   </e>
-GPF_SETUP       EQU     0
-GPFCON_Val      EQU     0x00000000
-GPFUP_Val       EQU     0x00000000
-
-;//   <e> Port G Settings
-;//     <h> Port G Control Register (GPGCON)
-;//       <o1.30..31> GPG15     <0=> Input <1=> Output <2=> EINT[23] <3=> Reserved
-;//       <o1.28..29> GPG14     <0=> Input <1=> Output <2=> EINT[22] <3=> Reserved
-;//       <o1.26..27> GPG13     <0=> Input <1=> Output <2=> EINT[21] <3=> Reserved
-;//       <o1.24..25> GPG12     <0=> Input <1=> Output <2=> EINT[20] <3=> Reserved
-;//       <o1.22..23> GPG11     <0=> Input <1=> Output <2=> EINT[19] <3=> TCLK[1]
-;//       <o1.20..21> GPG10     <0=> Input <1=> Output <2=> EINT[18] <3=> nCTS1
-;//       <o1.18..19> GPG9      <0=> Input <1=> Output <2=> EINT[17] <3=> nRTS1
-;//       <o1.16..17> GPG8      <0=> Input <1=> Output <2=> EINT[16] <3=> Reserved
-;//       <o1.14..15> GPG7      <0=> Input <1=> Output <2=> EINT[15] <3=> SPICLK1
-;//       <o1.12..13> GPG6      <0=> Input <1=> Output <2=> EINT[14] <3=> SPIMOSI1
-;//       <o1.10..11> GPG5      <0=> Input <1=> Output <2=> EINT[13] <3=> SPIMISO1
-;//       <o1.8..9>   GPG4      <0=> Input <1=> Output <2=> EINT[12] <3=> LCD_PWRDN
-;//       <o1.6..7>   GPG3      <0=> Input <1=> Output <2=> EINT[11] <3=> nSS1
-;//       <o1.4..5>   GPG2      <0=> Input <1=> Output <2=> EINT[10] <3=> nSS0
-;//       <o1.2..3>   GPG1      <0=> Input <1=> Output <2=> EINT[9]  <3=> Reserved
-;//       <o1.0..1>   GPG0      <0=> Input <1=> Output <2=> EINT[8]  <3=> Reserved
-;//     </h>
-;//     <h> Port G Pull-up Settings Register (GPGUP)
-;//       <o2.15>     GPG15 Pull-up Disable
-;//       <o2.14>     GPG14 Pull-up Disable
-;//       <o2.13>     GPG13 Pull-up Disable
-;//       <o2.12>     GPG12 Pull-up Disable
-;//       <o2.11>     GPG11 Pull-up Disable
-;//       <o2.10>     GPG10 Pull-up Disable
-;//       <o2.9>      GPG9  Pull-up Disable
-;//       <o2.8>      GPG8  Pull-up Disable
-;//       <o2.7>      GPG7  Pull-up Disable
-;//       <o2.6>      GPG6  Pull-up Disable
-;//       <o2.5>      GPG5  Pull-up Disable
-;//       <o2.4>      GPG4  Pull-up Disable
-;//       <o2.3>      GPG3  Pull-up Disable
-;//       <o2.2>      GPG2  Pull-up Disable
-;//       <o2.1>      GPG1  Pull-up Disable
-;//       <o2.0>      GPG0  Pull-up Disable
-;//     </h>
-;//   </e>
-GPG_SETUP       EQU     0
-GPGCON_Val      EQU     0x00000000
-GPGUP_Val       EQU     0x00000000
-
-;//   <e> Port H Settings
-;//     <h> Port H Control Register (GPHCON)
-;//       <o1.20..21> GPH10     <0=> Input <1=> Output <2=> CLKOUT1  <3=> Reserved
-;//       <o1.18..19> GPH9      <0=> Input <1=> Output <2=> CLKOUT0  <3=> Reserved
-;//       <o1.16..17> GPH8      <0=> Input <1=> Output <2=> UEXTCLK  <3=> Reserved
-;//       <o1.14..15> GPH7      <0=> Input <1=> Output <2=> RXD[2]   <3=> nCTS1
-;//       <o1.12..13> GPH6      <0=> Input <1=> Output <2=> TXD[2]   <3=> nRTS1
-;//       <o1.10..11> GPH5      <0=> Input <1=> Output <2=> RXD[1]   <3=> Reserved
-;//       <o1.8..9>   GPH4      <0=> Input <1=> Output <2=> TXD[1]   <3=> Reserved
-;//       <o1.6..7>   GPH3      <0=> Input <1=> Output <2=> RXD[0]   <3=> Reserved
-;//       <o1.4..5>   GPH2      <0=> Input <1=> Output <2=> TXD[0]   <3=> Reserved
-;//       <o1.2..3>   GPH1      <0=> Input <1=> Output <2=> nRTS0    <3=> Reserved
-;//       <o1.0..1>   GPH0      <0=> Input <1=> Output <2=> nCTS0    <3=> Reserved
-;//     </h>
-;//     <h> Port H Pull-up Settings Register (GPHUP)
-;//       <o2.10>     GPH10 Pull-up Disable
-;//       <o2.9>      GPH9  Pull-up Disable
-;//       <o2.8>      GPH8  Pull-up Disable
-;//       <o2.7>      GPH7  Pull-up Disable
-;//       <o2.6>      GPH6  Pull-up Disable
-;//       <o2.5>      GPH5  Pull-up Disable
-;//       <o2.4>      GPH4  Pull-up Disable
-;//       <o2.3>      GPH3  Pull-up Disable
-;//       <o2.2>      GPH2  Pull-up Disable
-;//       <o2.1>      GPH1  Pull-up Disable
-;//       <o2.0>      GPH0  Pull-up Disable
-;//     </h>
-;//   </e>
-GPH_SETUP       EQU     0
-GPHCON_Val      EQU     0x00000000
-GPHUP_Val       EQU     0x00000000
-
-;//   <e> Port J Settings
-;//     <h> Port J Control Register (GPJCON)
-;//       <o1.24..25> GPJ12     <0=> Input <1=> Output <2=> CAMRESET   <3=> Reserved
-;//       <o1.22..23> GPJ11     <0=> Input <1=> Output <2=> CAMCLKOUT  <3=> Reserved
-;//       <o1.20..21> GPJ10     <0=> Input <1=> Output <2=> CAMHREF    <3=> Reserved
-;//       <o1.18..19> GPJ9      <0=> Input <1=> Output <2=> CAMVSYNC   <3=> Reserved
-;//       <o1.16..17> GPJ8      <0=> Input <1=> Output <2=> CAMPCLK    <3=> Reserved
-;//       <o1.14..15> GPJ7      <0=> Input <1=> Output <2=> CAMDATA[7] <3=> Reserved
-;//       <o1.12..13> GPJ6      <0=> Input <1=> Output <2=> CAMDATA[6] <3=> Reserved
-;//       <o1.10..11> GPJ5      <0=> Input <1=> Output <2=> CAMDATA[5] <3=> Reserved
-;//       <o1.8..9>   GPJ4      <0=> Input <1=> Output <2=> CAMDATA[4] <3=> Reserved
-;//       <o1.6..7>   GPJ3      <0=> Input <1=> Output <2=> CAMDATA[3] <3=> Reserved
-;//       <o1.4..5>   GPJ2      <0=> Input <1=> Output <2=> CAMDATA[2] <3=> Reserved
-;//       <o1.2..3>   GPJ1      <0=> Input <1=> Output <2=> CAMDATA[1] <3=> Reserved
-;//       <o1.0..1>   GPJ0      <0=> Input <1=> Output <2=> CAMDATA[0] <3=> Reserved
-;//     </h>
-;//     <h> Port J Pull-up Settings Register (GPJUP)
-;//       <o2.12>     GPJ12 Pull-up Disable
-;//       <o2.11>     GPJ11 Pull-up Disable
-;//       <o2.10>     GPJ10 Pull-up Disable
-;//       <o2.9>      GPJ9  Pull-up Disable
-;//       <o2.8>      GPJ8  Pull-up Disable
-;//       <o2.7>      GPJ7  Pull-up Disable
-;//       <o2.6>      GPJ6  Pull-up Disable
-;//       <o2.5>      GPJ5  Pull-up Disable
-;//       <o2.4>      GPJ4  Pull-up Disable
-;//       <o2.3>      GPJ3  Pull-up Disable
-;//       <o2.2>      GPJ2  Pull-up Disable
-;//       <o2.1>      GPJ1  Pull-up Disable
-;//       <o2.0>      GPJ0  Pull-up Disable
-;//     </h>
-;//   </e>
-GPJ_SETUP       EQU     0
-GPJCON_Val      EQU     0x00000000
-GPJUP_Val       EQU     0x00000000
-
-;// </e> I/O Setup
-
-		END

libcpu/arm/s3c24x0/lowlevel_init.S

@@ -1,137 +0,0 @@
-/*
- * File      : application.c
- * This file is part of RT-Thread RTOS
- * COPYRIGHT (C) 2006, RT-Thread Development Team
- *
- * The license and distribution terms for this file may be
- * found in the file LICENSE in this distribution or at
- * http://www.rt-thread.org/license/LICENSE
- *
- * Change Logs:
- * Date           Author       Notes
- * 2010-03-16     Gary Lee     the first version
- */
-
-#define BWSCON	        0x48000000
-
-/* BWSCON */
-#define DW8				(0x0)
-#define DW16			(0x1)
-#define DW32			(0x2)
-#define WAIT			(0x1<<2)
-#define UBLB			(0x1<<3)
-
-#define B1_BWSCON		(DW16)
-#define B2_BWSCON		(DW16)
-#define B3_BWSCON		(DW16 + WAIT + UBLB)
-#define B4_BWSCON		(DW16)
-#define B5_BWSCON		(DW16)
-#define B6_BWSCON		(DW32)
-#define B7_BWSCON		(DW32)
-
-#define B0_Tacs			0x0
-#define B0_Tcos			0x0
-#define B0_Tacc			0x7
-#define B0_Tcoh			0x0
-#define B0_Tah			0x0
-#define B0_Tacp			0x0
-#define B0_PMC			0x0
-
-#define B1_Tacs			0x0
-#define B1_Tcos			0x0
-#define B1_Tacc			0x7
-#define B1_Tcoh			0x0
-#define B1_Tah			0x0
-#define B1_Tacp			0x0
-#define B1_PMC			0x0
-
-#define B2_Tacs			0x0
-#define B2_Tcos			0x0
-#define B2_Tacc			0x7
-#define B2_Tcoh			0x0
-#define B2_Tah			0x0
-#define B2_Tacp			0x0
-#define B2_PMC			0x0
-
-#define B3_Tacs			0xc
-#define B3_Tcos			0x7
-#define B3_Tacc			0xf
-#define B3_Tcoh			0x1
-#define B3_Tah			0x0
-#define B3_Tacp			0x0
-#define B3_PMC			0x0
-
-#define B4_Tacs			0x0
-#define B4_Tcos			0x0
-#define B4_Tacc			0x7
-#define B4_Tcoh			0x0
-#define B4_Tah			0x0
-#define B4_Tacp			0x0
-#define B4_PMC			0x0
-
-#define B5_Tacs			0xc
-#define B5_Tcos			0x7
-#define B5_Tacc			0xf
-#define B5_Tcoh			0x1
-#define B5_Tah			0x0
-#define B5_Tacp			0x0
-#define B5_PMC			0x0
-
-#define B6_MT			0x3				/* SDRAM 											*/
-#define B6_Trcd			0x1
-#define B6_SCAN			0x1				/* 9bit 											*/
-
-#define B7_MT			0x3				/* SDRAM 											*/
-#define B7_Trcd			0x1				/* 3clk 											*/
-#define B7_SCAN			0x1				/* 9bit 											*/
-
-/* REFRESH parameter 					*/
-#define REFEN			0x1				/* Refresh enable 									*/
-#define TREFMD			0x0				/* CBR(CAS before RAS)/Auto refresh 				*/
-#define Trc				0x3				/* 7clk 											*/
-#define Tchr			0x2				/* 3clk 											*/
-
-#define Trp				0x2				/* 4clk 											*/
-#define REFCNT			1012
-
-/**************************************/
-
-.globl lowlevel_init
-lowlevel_init:
-	/* memory control configuration 	*/
-	/* make r0 relative the current location so that it 									*/
-	/* reads SMRDATA out of FLASH rather than memory ! 										*/
-	ldr     r0, =SMRDATA
-	ldr	    r1, =lowlevel_init
-	sub	    r0, r0, r1
-	adr	    r3, lowlevel_init			/* r3 <- current position of code   				*/
-	add     r0, r0, r3
-	ldr	    r1, =BWSCON					/* Bus Width Status Controller 						*/
-	add     r2, r0, #13*4
-0:
-	ldr     r3, [r0], #4
-	str     r3, [r1], #4
-	cmp     r2, r0
-	bne     0b
-
-	/* everything is fine now 			*/
-	mov	    pc, lr
-
-	.ltorg
-/* the literal pools origin 			*/
-
-SMRDATA:
-    .word (0+(B1_BWSCON<<4)+(B2_BWSCON<<8)+(B3_BWSCON<<12)+(B4_BWSCON<<16)+(B5_BWSCON<<20)+(B6_BWSCON<<24)+(B7_BWSCON<<28))
-    .word ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC))
-    .word ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC))
-    .word ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC))
-    .word ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC))
-    .word ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC))
-    .word ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC))
-    .word ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN))
-    .word ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN))
-    .word ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT)
-    .word 0xb2
-    .word 0x30
-    .word 0x30
-    

libcpu/arm/s3c24x0/nand_read.c

@@ -1,67 +0,0 @@
-/* 
- * nand flash read
- */
-
-#define NFCONF				(*(volatile unsigned int  *)0x4e000000)
-#define rNFCONT				(*(volatile unsigned int  *)0x4E000004)
-#define NFCMD				(*(volatile unsigned int  *)0x4e000008)
-#define NFADDR				(*(volatile unsigned char *)0x4e00000C)
-#define NFDATA				(*(volatile unsigned char *)0x4e000010)
-#define NFSTAT				(*(volatile unsigned char *)0x4e000020)
-
-#define BUSY				1
-
-#define NAND_SECTOR_SIZE	512
-#define NAND_BLOCK_MASK		(NAND_SECTOR_SIZE - 1)
-
-void wait_idle(void) {
-	int i;
-
-	while (!(NFSTAT & BUSY)) {
-		for(i=0; i<10; i++) {
-			;
-		}
-	}
-}
-
-/* low level nand read function */
-int nand_read_ll(unsigned char *buf, unsigned long start_addr, int size)
-{
-	int i, j;
-
-	/*
-	 * K9F5608UOC asks for 512B per page, and read/write operation must
-	 * do with page. Therefore, first judge whether start_addr and size
-	 * are valid.
-	 */ 
-	if ((start_addr & NAND_BLOCK_MASK) || (size & NAND_BLOCK_MASK)) {
-		return -1;	/* invalid alignment */
-	}
-
-	/* chip Enable */
-	NFCONF &= ~0x800;
-	for (i=0; i<10; i++) {
-		;
-	}
-
-	for (i=start_addr; i < (start_addr + size); i+=NAND_SECTOR_SIZE) {
-		NFCMD = 0;
-
-		/* Write Address */
-		NFADDR = i & 0xff;
-		NFADDR = (i >> 9) & 0xff;
-		NFADDR = (i >> 17) & 0xff;
-		NFADDR = (i >> 25) & 0xff;
-
-		wait_idle();
-
- 		for(j=0; j < NAND_SECTOR_SIZE; j++) {
-			*buf++ = (NFDATA & 0xff);
-		}
-	}
-
-	/* chip Disable */
-	NFCONF |= 0x800;	/* chip disable */
-
-	return 0;
-}

libcpu/arm/s3c24x0/start_gcc.S

@@ -10,8 +10,8 @@
  * Change Logs:
  * Date           Author       Notes
  * 2006-03-13     Bernard      first version
- * 2006-10-05     Alsor.Z      for s3c2440 initialize
- * 2008-01-29     Yi.Qiu       for QEMU emulator
+ * 2006-10-05     Alsor.Z       for s3c2440 initialize
+ * 2008-01-29     Yi.Qiu         for QEMU emulator
  */
 
 #define CONFIG_STACKSIZE 	512
@@ -23,7 +23,7 @@
 #define S_LR  				56
 #define S_SP  				52
 
-#define S_IP  				48
+#define S_IP  					48
 #define S_FP  				44
 #define S_R10  				40
 #define S_R9  				36
@@ -88,14 +88,14 @@
 
 .globl _start
 _start:
-	b		    reset
-	ldr		    pc, _vector_undef
-	ldr		    pc, _vector_swi
-	ldr		    pc, _vector_pabt
-	ldr		    pc, _vector_dabt
-	ldr		    pc, _vector_resv
-	ldr		    pc, _vector_irq
-	ldr		    pc, _vector_fiq
+	b		reset
+	ldr		pc, _vector_undef
+	ldr		pc, _vector_swi
+	ldr		pc, _vector_pabt
+	ldr		pc, _vector_dabt
+	ldr		pc, _vector_resv
+	ldr		pc, _vector_irq
+	ldr		pc, _vector_fiq
 
 _vector_undef:	.word vector_undef
 _vector_swi:	.word vector_swi
@@ -105,7 +105,7 @@ _vector_resv:	.word vector_resv
 _vector_irq:	.word vector_irq
 _vector_fiq:	.word vector_fiq
 
-.balignl 	    16, 0xdeadbeef
+.balignl 	16,0xdeadbeef
 
 /*
  *************************************************************************
@@ -116,21 +116,26 @@ _vector_fiq:	.word vector_fiq
  * jump to second stage
  *
  *************************************************************************
- */       
-_TEXT_BASE:                  /* TEXT_BASE was defined in rtconfig.py */
+ */
+
+_TEXT_BASE:
 	.word	TEXT_BASE
 
-/* rtthread kernel start and end which are defined in linker script */
+/*
+ * rtthread kernel start and end
+ * which are defined in linker script
+ */
 .globl _rtthread_start
 _rtthread_start:
 	.word _start
-
-/* _end	was defined in link script                                  */
+	
 .globl _rtthread_end
 _rtthread_end:
 	.word  _end
 
-/* rtthread bss start and end which are defined in linker script    */
+/*
+ * rtthread bss start and end which are defined in linker script
+ */
 .globl _bss_start
 _bss_start:	
 	.word __bss_start
@@ -160,32 +165,20 @@ ABORT_STACK_START:
 _STACK_START:
 	.word _svc_stack_start + 4096
 
-.globl _load_address
-#if defined (__FLASH_BUILD__)
-_load_address: 
-	.word ROM_BASE + _TEXT_BASE
-#else
-_load_address: 
-	.word RAM_BASE + _TEXT_BASE
-#endif	
-
-/*
- *************************************************************************
- * Actual start (entry point)
- *************************************************************************
- */
+/* ----------------------------------entry------------------------------*/
 reset:
-	/* set the cpu to SVC32 mode 	                                    */
-	mrs		r0, cpsr
-	bic		r0, r0,#MODEMASK
-	orr		r0, r0,#SVCMODE
-	msr		cpsr, r0
 	
-    /* watch dog disable 			                                    */   
-	ldr 	r0, =WTCON
-	ldr 	r1, =0x0
-	str 	r1, [r0]
+	/* set the cpu to SVC32 mode 	*/
+	mrs		r0,cpsr
+	bic		r0,r0,#MODEMASK
+	orr		r0,r0,#SVCMODE
+	msr		cpsr,r0
 	
+	/* watch dog disable 			*/
+	ldr 	r0,=WTCON
+	ldr 	r1,=0x0
+	str 	r1,[r0]
+
 	/* mask all IRQs by clearing all bits in the INTMRs 				*/
 	ldr		r1, =INTMSK
 	ldr		r0, =0xffffffff
@@ -195,7 +188,7 @@ reset:
 	str		r0, [r1]
 
 	/* set interrupt vector 		*/
-	ldr 	r0, _load_address       /* _load_address = 0x30000000       */
+	ldr 	r0, _load_address
 	mov		r1, #0x0				/* target address    				*/
 	add		r2, r0, #0x20			/* size, 32bytes         			*/
 
@@ -204,9 +197,11 @@ copy_loop:
 	stmia	r1!, {r3-r10}			/* copy to   target address [r1]    */
 	cmp		r0, r2					/* until source end addreee [r2]    */
 	ble		copy_loop
-	
+
+	/* setup stack */
 	bl		stack_setup
-    /* clear .bss */ 
+
+	/* clear .bss */
 	mov   	r0,#0                   /* get a zero 						*/
 	ldr   	r1,=__bss_start         /* bss start 						*/
 	ldr   	r2,=__bss_end           /* bss end 							*/
@@ -214,61 +209,37 @@ copy_loop:
 bss_loop:
 	cmp   	r1,r2                   /* check if data to clear 			*/
 	strlo 	r0,[r1],#4              /* clear 4 bytes 					*/
-	blo   	bss_loop                /* loop until done 					*/	
+	blo   	bss_loop                /* loop until done 					*/
+
 	/* call C++ constructors of global objects 							*/
 	ldr 	r0, =__ctors_start__
 	ldr 	r1, =__ctors_end__
 	
 ctor_loop:
-    cmp     r0, r1
-	beq 	kernel_start
+	cmp 	r0, r1
+	beq 	ctor_end
 	ldr 	r2, [r0], #4
 	stmfd 	sp!, {r0-r1}
 	mov 	lr, pc
 	bx 		r2
 	ldmfd 	sp!, {r0-r1}
 	b		ctor_loop
+	
+ctor_end:
 
-kernel_start:
-	/* start RT-Thread Kernel 		                                    */
+	/* start RT-Thread Kernel 		*/
 	ldr		pc, _rtthread_startup
 
 _rtthread_startup: 
-	.word rtthread_startup	
-/*
- *************************************************************************
- * Subroutines
- *************************************************************************
- */
-stack_setup:
-	mrs		r0, cpsr
-	bic		r0, r0, #MODEMASK
-	orr		r1, r0, #UNDEFMODE|NOINT
-	msr		cpsr_cxsf, r1			/* undef mode						*/
-	ldr		sp, UNDEFINED_STACK_START
-
-	orr		r1,r0,#ABORTMODE|NOINT
-	msr		cpsr_cxsf,r1			/* abort mode						*/
-	ldr		sp, ABORT_STACK_START
-
-	orr		r1,r0,#IRQMODE|NOINT
-	msr		cpsr_cxsf,r1			/* IRQ mode							*/
-	ldr		sp, IRQ_STACK_START
-
-	orr		r1,r0,#FIQMODE|NOINT
-	msr		cpsr_cxsf,r1			/* FIQ mode							*/
-	ldr		sp, FIQ_STACK_START
-
-	bic		r0,r0,#MODEMASK
-	orr		r1,r0,#SVCMODE|NOINT
-	msr		cpsr_cxsf,r1			/* SVC mode							*/
-
-	ldr		sp, _STACK_START
-
-	/* USER mode is not initialized. */
+	.word rtthread_startup
+#if defined (__FLASH_BUILD__)
+_load_address: 
+	.word ROM_BASE + _TEXT_BASE
+#else
+_load_address: 
+	.word RAM_BASE + _TEXT_BASE
+#endif
 
-	mov		pc,lr					/* The LR register may be not valid for the mode changes.*/
-	
 /*
  *************************************************************************
  *
@@ -387,4 +358,33 @@ _interrupt_thread_switch:
 
 	ldmfd	sp!, {r0-r12,lr,pc}		/* pop new task's r0-r12,lr & pc	*/
 
+stack_setup:
+	mrs		r0, cpsr
+	bic		r0, r0, #MODEMASK
+	orr		r1, r0, #UNDEFMODE|NOINT
+	msr		cpsr_cxsf, r1			/* undef mode						*/
+	ldr		sp, UNDEFINED_STACK_START
+
+	orr		r1,r0,#ABORTMODE|NOINT
+	msr		cpsr_cxsf,r1			/* abort mode						*/
+	ldr		sp, ABORT_STACK_START
+
+	orr		r1,r0,#IRQMODE|NOINT
+	msr		cpsr_cxsf,r1			/* IRQ mode							*/
+	ldr		sp, IRQ_STACK_START
+
+	orr		r1,r0,#FIQMODE|NOINT
+	msr		cpsr_cxsf,r1			/* FIQ mode							*/
+	ldr		sp, FIQ_STACK_START
+
+	bic		r0,r0,#MODEMASK
+	orr		r1,r0,#SVCMODE|NOINT
+	msr		cpsr_cxsf,r1			/* SVC mode							*/
+
+	ldr		sp, _STACK_START
+
+	/* USER mode is not initialized. */
+	mov		pc,lr					/* The LR register may be not valid for the mode changes.*/
+
 /*/*}*/
+