完善ADC驱动，格式化代码 (#5232)

[AT32] 完善ADC驱动

bsp/n32g452xx/Libraries/rt_drivers/drv_adc.c

@@ -44,63 +44,63 @@ static rt_uint32_t n32_adc_get_channel(rt_uint32_t channel)
 
     switch (channel)
     {
-        case  0:
-            n32_channel = ADC_CH_0;
-            break;
-        case  1:
-            n32_channel = ADC_CH_1;
-            break;
-        case  2:
-            n32_channel = ADC_CH_2;
-            break;
-        case  3:
-            n32_channel = ADC_CH_3;
-            break;
-        case  4:
-            n32_channel = ADC_CH_4;
-            break;
-        case  5:
-            n32_channel = ADC_CH_5;
-            break;
-        case  6:
-            n32_channel = ADC_CH_6;
-            break;
-        case  7:
-            n32_channel = ADC_CH_7;
-            break;
-        case  8:
-            n32_channel = ADC_CH_8;
-            break;
-        case  9:
-            n32_channel = ADC_CH_9;
-            break;
-        case 10:
-            n32_channel = ADC_CH_10;
-            break;
-        case 11:
-            n32_channel = ADC_CH_11;
-            break;
-        case 12:
-            n32_channel = ADC_CH_12;
-            break;
-        case 13:
-            n32_channel = ADC_CH_13;
-            break;
-        case 14:
-            n32_channel = ADC_CH_14;
-            break;
-        case 15:
-            n32_channel = ADC_CH_15;
-            break;
-        case 16:
-            n32_channel = ADC_CH_16;
-            break;
-        case 17:
-            n32_channel = ADC_CH_17;
-            break;
-        case 18:
-            n32_channel = ADC_CH_18;
-            break;
+    case  0:
+        n32_channel = ADC_CH_0;
+        break;
+    case  1:
+        n32_channel = ADC_CH_1;
+        break;
+    case  2:
+        n32_channel = ADC_CH_2;
+        break;
+    case  3:
+        n32_channel = ADC_CH_3;
+        break;
+    case  4:
+        n32_channel = ADC_CH_4;
+        break;
+    case  5:
+        n32_channel = ADC_CH_5;
+        break;
+    case  6:
+        n32_channel = ADC_CH_6;
+        break;
+    case  7:
+        n32_channel = ADC_CH_7;
+        break;
+    case  8:
+        n32_channel = ADC_CH_8;
+        break;
+    case  9:
+        n32_channel = ADC_CH_9;
+        break;
+    case 10:
+        n32_channel = ADC_CH_10;
+        break;
+    case 11:
+        n32_channel = ADC_CH_11;
+        break;
+    case 12:
+        n32_channel = ADC_CH_12;
+        break;
+    case 13:
+        n32_channel = ADC_CH_13;
+        break;
+    case 14:
+        n32_channel = ADC_CH_14;
+        break;
+    case 15:
+        n32_channel = ADC_CH_15;
+        break;
+    case 16:
+        n32_channel = ADC_CH_16;
+        break;
+    case 17:
+        n32_channel = ADC_CH_17;
+        break;
+    case 18:
+        n32_channel = ADC_CH_18;
+        break;
     }
 
     return n32_channel;
@@ -124,27 +124,23 @@ static rt_err_t n32_adc_enabled(struct rt_adc_device *device, rt_uint32_t channe
     ADC_InitStructure.ChsNumber             = 1;
     ADC_Init(n32_adc_handler, &ADC_InitStructure);
 
-    /* ADCx regular channels configuration */
-    ADC_ConfigRegularChannel(n32_adc_handler, n32_adc_get_channel(channel), 1, ADC_SAMP_TIME_28CYCLES5);
-
     if (((n32_adc_handler == ADC2) || (n32_adc_handler == ADC2))
-        && ((n32_adc_get_channel(channel) == ADC_CH_16) || (n32_adc_get_channel(channel) == ADC_CH_18)))
+            && ((n32_adc_get_channel(channel) == ADC_CH_16)
+                || (n32_adc_get_channel(channel) == ADC_CH_18)))
     {
         ADC_EnableTempSensorVrefint(ENABLE);
     }
 
-    /* Enable ADCx */
-    ADC_Enable(n32_adc_handler, ENABLE);
-
-    /* Start ADCx calibration */
-    ADC_StartCalibration(n32_adc_handler);
-    /* Check the end of ADCx calibration */
-    while(ADC_GetCalibrationStatus(n32_adc_handler));
-
     if (enabled)
     {
         /* Enable ADC1 */
         ADC_Enable(n32_adc_handler, ENABLE);
+        /*Check ADC Ready*/
+        while (ADC_GetFlagStatusNew(n32_adc_handler, ADC_FLAG_RDY) == RESET);
+        /* Start ADCx calibration */
+        ADC_StartCalibration(n32_adc_handler);
+        /* Check the end of ADCx calibration */
+        while (ADC_GetCalibrationStatus(n32_adc_handler));
     }
     else
     {
@@ -164,11 +160,16 @@ static rt_err_t n32_get_adc_value(struct rt_adc_device *device, rt_uint32_t chan
 
     n32_adc_handler = device->parent.user_data;
 
+    /* ADCx regular channels configuration */
+    ADC_ConfigRegularChannel(n32_adc_handler, n32_adc_get_channel(channel), 1, ADC_SAMP_TIME_28CYCLES5);
+
     /* Start ADCx Software Conversion */
     ADC_EnableSoftwareStartConv(n32_adc_handler, ENABLE);
 
     /* Wait for the ADC to convert */
-    while(ADC_GetFlagStatus(n32_adc_handler, ADC_FLAG_ENDC) == RESET);
+    while (ADC_GetFlagStatus(n32_adc_handler, ADC_FLAG_ENDC) == RESET);
+
+    ADC_ClearFlag(n32_adc_handler, ADC_FLAG_ENDC);
 
     /* get ADC value */
     *value = ADC_GetDat(n32_adc_handler);
@@ -191,8 +192,8 @@ static int rt_hw_adc_init(void)
     {
         /* register ADC device */
         if (rt_hw_adc_register(&n32_adc_obj[i].n32_adc_device,
-                    n32_adc_obj[i].name, &at_adc_ops,
-                    n32_adc_obj[i].ADC_Handler) == RT_EOK)
+                               n32_adc_obj[i].name, &at_adc_ops,
+                               n32_adc_obj[i].ADC_Handler) == RT_EOK)
         {
             LOG_D("%s register success", n32_adc_obj[i].name);
         }

bsp/n32g452xx/Libraries/rt_drivers/drv_common.c

@@ -12,11 +12,11 @@
 #include "board.h"
 
 #ifdef RT_USING_SERIAL
-#ifdef RT_USING_SERIAL_V2
-#include "drv_usart_v2.h"
-#else
-#include "drv_usart.h"
-#endif
+    #ifdef RT_USING_SERIAL_V2
+        #include "drv_usart_v2.h"
+    #else
+        #include "drv_usart.h"
+    #endif
 #endif
 
 #ifdef RT_USING_FINSH

bsp/n32g452xx/Libraries/rt_drivers/drv_common.h

@@ -14,7 +14,7 @@
 #include <rtthread.h>
 #include <rthw.h>
 #ifdef RT_USING_DEVICE
-#include <rtdevice.h>
+    #include <rtdevice.h>
 #endif
 
 #ifdef __cplusplus

bsp/n32g452xx/Libraries/rt_drivers/drv_flash.c

@@ -15,7 +15,7 @@
 #include "drv_flash.h"
 
 #if defined(PKG_USING_FAL)
-#include "fal.h"
+    #include "fal.h"
 #endif
 
 //#define DRV_DEBUG
@@ -147,11 +147,11 @@ int n32_flash_erase(rt_uint32_t addr, size_t size)
         return -RT_EINVAL;
     }
 
-    while(addr < end_addr)
+    while (addr < end_addr)
     {
         page_addr = get_page(addr);
 
-        if(FLASH_EraseOnePage(page_addr) != FLASH_COMPL)
+        if (FLASH_EraseOnePage(page_addr) != FLASH_COMPL)
         {
             result = -RT_ERROR;
             goto __exit;
@@ -160,10 +160,10 @@ int n32_flash_erase(rt_uint32_t addr, size_t size)
         addr += FLASH_PAGE_SIZE;
     }
 
-        FLASH_Lock();
+    FLASH_Lock();
 
 __exit:
-    if(result != RT_EOK)
+    if (result != RT_EOK)
     {
         return result;
     }

bsp/n32g452xx/Libraries/rt_drivers/drv_gpio.c

@@ -573,9 +573,9 @@ void n32_pin_mode(rt_device_t dev, rt_base_t pin, rt_base_t mode)
 rt_inline rt_int32_t bit2bitno(rt_uint32_t bit)
 {
     int i;
-    for(i = 0; i < 32; i++)
+    for (i = 0; i < 32; i++)
     {
-        if((0x01 << i) == bit)
+        if ((0x01 << i) == bit)
         {
             return i;
         }
@@ -585,7 +585,7 @@ rt_inline rt_int32_t bit2bitno(rt_uint32_t bit)
 rt_inline const struct pin_irq_map *get_pin_irq_map(uint32_t pinbit)
 {
     rt_int32_t mapindex = bit2bitno(pinbit);
-    if(mapindex < 0 || mapindex >= ITEM_NUM(pin_irq_map))
+    if (mapindex < 0 || mapindex >= ITEM_NUM(pin_irq_map))
     {
         return RT_NULL;
     }
@@ -604,22 +604,22 @@ rt_err_t n32_pin_attach_irq(struct rt_device *device, rt_int32_t pin,
         return -RT_ENOSYS;
     }
     irqindex = bit2bitno(index->pin);
-    if(irqindex < 0 || irqindex >= ITEM_NUM(pin_irq_map))
+    if (irqindex < 0 || irqindex >= ITEM_NUM(pin_irq_map))
     {
         return -RT_ENOSYS;
     }
 
     level = rt_hw_interrupt_disable();
-    if(pin_irq_hdr_tab[irqindex].pin == pin   &&
-       pin_irq_hdr_tab[irqindex].hdr == hdr   &&
-       pin_irq_hdr_tab[irqindex].mode == mode &&
-       pin_irq_hdr_tab[irqindex].args == args
-      )
+    if (pin_irq_hdr_tab[irqindex].pin == pin   &&
+            pin_irq_hdr_tab[irqindex].hdr == hdr   &&
+            pin_irq_hdr_tab[irqindex].mode == mode &&
+            pin_irq_hdr_tab[irqindex].args == args
+       )
     {
         rt_hw_interrupt_enable(level);
         return RT_EOK;
     }
-    if(pin_irq_hdr_tab[irqindex].pin != -1)
+    if (pin_irq_hdr_tab[irqindex].pin != -1)
     {
         rt_hw_interrupt_enable(level);
         return -RT_EBUSY;
@@ -644,13 +644,13 @@ rt_err_t n32_pin_dettach_irq(struct rt_device *device, rt_int32_t pin)
         return -RT_ENOSYS;
     }
     irqindex = bit2bitno(index->pin);
-    if(irqindex < 0 || irqindex >= ITEM_NUM(pin_irq_map))
+    if (irqindex < 0 || irqindex >= ITEM_NUM(pin_irq_map))
     {
         return -RT_ENOSYS;
     }
 
     level = rt_hw_interrupt_disable();
-    if(pin_irq_hdr_tab[irqindex].pin == -1)
+    if (pin_irq_hdr_tab[irqindex].pin == -1)
     {
         rt_hw_interrupt_enable(level);
         return RT_EOK;
@@ -679,15 +679,15 @@ rt_err_t n32_pin_irq_enable(struct rt_device *device, rt_base_t pin,
     {
         return -RT_ENOSYS;
     }
-    if(enabled == PIN_IRQ_ENABLE)
+    if (enabled == PIN_IRQ_ENABLE)
     {
         irqindex = bit2bitno(index->pin);
-        if(irqindex < 0 || irqindex >= ITEM_NUM(pin_irq_map))
+        if (irqindex < 0 || irqindex >= ITEM_NUM(pin_irq_map))
         {
             return -RT_ENOSYS;
         }
         level = rt_hw_interrupt_disable();
-        if(pin_irq_hdr_tab[irqindex].pin == -1)
+        if (pin_irq_hdr_tab[irqindex].pin == -1)
         {
             rt_hw_interrupt_enable(level);
             return -RT_ENOSYS;
@@ -701,35 +701,35 @@ rt_err_t n32_pin_irq_enable(struct rt_device *device, rt_base_t pin,
         GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
         GPIO_InitPeripheral(index->gpio, &GPIO_InitStructure);
 
-        NVIC_InitStructure.NVIC_IRQChannel= irqmap->irqno;
-        NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority= 2;
-        NVIC_InitStructure.NVIC_IRQChannelSubPriority= 2;
-        NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;
+        NVIC_InitStructure.NVIC_IRQChannel = irqmap->irqno;
+        NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
+        NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
+        NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
         NVIC_Init(&NVIC_InitStructure);
 
         GPIO_ConfigEXTILine(index->port_source, index->pin_source);
         EXTI_InitStructure.EXTI_Line = irqmap->irqbit;
         EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
-        switch(pin_irq_hdr_tab[irqindex].mode)
+        switch (pin_irq_hdr_tab[irqindex].mode)
         {
-            case PIN_IRQ_MODE_RISING:
-                EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
-                break;
-            case PIN_IRQ_MODE_FALLING:
-                EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
-                break;
-            case PIN_IRQ_MODE_RISING_FALLING:
-                EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
-                break;
+        case PIN_IRQ_MODE_RISING:
+            EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
+            break;
+        case PIN_IRQ_MODE_FALLING:
+            EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
+            break;
+        case PIN_IRQ_MODE_RISING_FALLING:
+            EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
+            break;
         }
         EXTI_InitStructure.EXTI_LineCmd = ENABLE;
         EXTI_InitPeripheral(&EXTI_InitStructure);
         rt_hw_interrupt_enable(level);
     }
-    else if(enabled == PIN_IRQ_DISABLE)
+    else if (enabled == PIN_IRQ_DISABLE)
     {
         irqmap = get_pin_irq_map(index->pin);
-        if(irqmap == RT_NULL)
+        if (irqmap == RT_NULL)
         {
             return -RT_ENOSYS;
         }
@@ -768,7 +768,7 @@ INIT_BOARD_EXPORT(n32_hw_pin_init);
 rt_inline void pin_irq_hdr(int irqno)
 {
     EXTI_ClrITPendBit(pin_irq_map[irqno].irqbit);
-    if(pin_irq_hdr_tab[irqno].hdr)
+    if (pin_irq_hdr_tab[irqno].hdr)
     {
         pin_irq_hdr_tab[irqno].hdr(pin_irq_hdr_tab[irqno].args);
     }
@@ -817,23 +817,23 @@ void EXTI9_5_IRQHandler(void)
 {
     /* enter interrupt */
     rt_interrupt_enter();
-    if(EXTI_GetITStatus(EXTI_LINE5) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE5) != RESET)
     {
         pin_irq_hdr(5);
     }
-    if(EXTI_GetITStatus(EXTI_LINE6) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE6) != RESET)
     {
         pin_irq_hdr(6);
     }
-    if(EXTI_GetITStatus(EXTI_LINE7) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE7) != RESET)
     {
         pin_irq_hdr(7);
     }
-    if(EXTI_GetITStatus(EXTI_LINE8) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE8) != RESET)
     {
         pin_irq_hdr(8);
     }
-    if(EXTI_GetITStatus(EXTI_LINE9) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE9) != RESET)
     {
         pin_irq_hdr(9);
     }
@@ -844,27 +844,27 @@ void EXTI15_10_IRQHandler(void)
 {
     /* enter interrupt */
     rt_interrupt_enter();
-    if(EXTI_GetITStatus(EXTI_LINE10) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE10) != RESET)
     {
         pin_irq_hdr(10);
     }
-    if(EXTI_GetITStatus(EXTI_LINE11) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE11) != RESET)
     {
         pin_irq_hdr(11);
     }
-    if(EXTI_GetITStatus(EXTI_LINE12) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE12) != RESET)
     {
         pin_irq_hdr(12);
     }
-    if(EXTI_GetITStatus(EXTI_LINE13) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE13) != RESET)
     {
         pin_irq_hdr(13);
     }
-    if(EXTI_GetITStatus(EXTI_LINE14) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE14) != RESET)
     {
         pin_irq_hdr(14);
     }
-    if(EXTI_GetITStatus(EXTI_LINE15) != RESET)
+    if (EXTI_GetITStatus(EXTI_LINE15) != RESET)
     {
         pin_irq_hdr(15);
     }

bsp/n32g452xx/Libraries/rt_drivers/drv_hwtimer.c

@@ -82,7 +82,7 @@ enum
 struct n32_hwtimer
 {
     rt_hwtimer_t    time_device;
-    TIM_Module*     tim_handle;
+    TIM_Module     *tim_handle;
     IRQn_Type       tim_irqn;
     char            *name;
 };
@@ -198,7 +198,7 @@ static void n32_timer_init(struct rt_hwtimer_device *timer, rt_uint32_t state)
         NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
         NVIC_Init(&NVIC_InitStructure);
 
-        TIM_ConfigInt(tim, TIM_INT_UPDATE ,ENABLE);
+        TIM_ConfigInt(tim, TIM_INT_UPDATE, ENABLE);
         TIM_ClrIntPendingBit(tim, TIM_INT_UPDATE);
 
         LOG_D("%s init success", tim_device->name);
@@ -270,29 +270,29 @@ static rt_err_t n32_timer_ctrl(rt_hwtimer_t *timer, rt_uint32_t cmd, void *arg)
 
     tim = (TIM_Module *)timer->parent.user_data;
 
-    switch(cmd)
+    switch (cmd)
     {
-        case HWTIMER_CTRL_FREQ_SET:
-        {
-            rt_uint32_t freq;
-            rt_uint16_t val;
+    case HWTIMER_CTRL_FREQ_SET:
+    {
+        rt_uint32_t freq;
+        rt_uint16_t val;
 
-            /* set timer frequence */
-            freq = *((rt_uint32_t *)arg);
+        /* set timer frequence */
+        freq = *((rt_uint32_t *)arg);
 
-            /* time init */
-            RCC_GetClocksFreqValue(&RCC_ClockStruct);
+        /* time init */
+        RCC_GetClocksFreqValue(&RCC_ClockStruct);
 
-            val = RCC_ClockStruct.SysclkFreq / freq;
+        val = RCC_ClockStruct.SysclkFreq / freq;
 
-            TIM_ConfigPrescaler(tim, val - 1, TIM_PSC_RELOAD_MODE_IMMEDIATE);
-        }
-        break;
-        default:
-        {
-            result = -RT_ENOSYS;
-        }
-        break;
+        TIM_ConfigPrescaler(tim, val - 1, TIM_PSC_RELOAD_MODE_IMMEDIATE);
+    }
+    break;
+    default:
+    {
+        result = -RT_ENOSYS;
+    }
+    break;
     }
 
     return result;
@@ -314,7 +314,7 @@ void TIM2_IRQHandler(void)
     /* enter interrupt */
     rt_interrupt_enter();
 
-    if(TIM_GetIntStatus(TIM2, TIM_INT_UPDATE) == SET)
+    if (TIM_GetIntStatus(TIM2, TIM_INT_UPDATE) == SET)
     {
 
         rt_device_hwtimer_isr(&n32_hwtimer_obj[TIM2_INDEX].time_device);
@@ -332,7 +332,7 @@ void TIM3_IRQHandler(void)
     /* enter interrupt */
     rt_interrupt_enter();
 
-    if(TIM_GetIntStatus(TIM3, TIM_INT_UPDATE) == SET)
+    if (TIM_GetIntStatus(TIM3, TIM_INT_UPDATE) == SET)
     {
 
         rt_device_hwtimer_isr(&n32_hwtimer_obj[TIM3_INDEX].time_device);
@@ -350,7 +350,7 @@ void TIM4_IRQHandler(void)
     /* enter interrupt */
     rt_interrupt_enter();
 
-    if(TIM_GetIntStatus(TIM4, TIM_INT_UPDATE) == SET)
+    if (TIM_GetIntStatus(TIM4, TIM_INT_UPDATE) == SET)
     {
 
         rt_device_hwtimer_isr(&n32_hwtimer_obj[TIM4_INDEX].time_device);
@@ -368,7 +368,7 @@ void TIM5_IRQHandler(void)
     /* enter interrupt */
     rt_interrupt_enter();
 
-    if(TIM_GetIntStatus(TIM5, TIM_INT_UPDATE) == SET)
+    if (TIM_GetIntStatus(TIM5, TIM_INT_UPDATE) == SET)
     {
 
         rt_device_hwtimer_isr(&n32_hwtimer_obj[TIM5_INDEX].time_device);
@@ -386,7 +386,7 @@ void TIM6_IRQHandler(void)
     /* enter interrupt */
     rt_interrupt_enter();
 
-    if(TIM_GetIntStatus(TIM6, TIM_INT_UPDATE) == SET)
+    if (TIM_GetIntStatus(TIM6, TIM_INT_UPDATE) == SET)
     {
 
         rt_device_hwtimer_isr(&n32_hwtimer_obj[TIM6_INDEX].time_device);
@@ -404,7 +404,7 @@ void TIM7_IRQHandler(void)
     /* enter interrupt */
     rt_interrupt_enter();
 
-    if(TIM_GetIntStatus(TIM7, TIM_INT_UPDATE) == SET)
+    if (TIM_GetIntStatus(TIM7, TIM_INT_UPDATE) == SET)
     {
 
         rt_device_hwtimer_isr(&n32_hwtimer_obj[TIM7_INDEX].time_device);

bsp/n32g452xx/Libraries/rt_drivers/drv_log.h

@@ -13,15 +13,15 @@
  */
 
 #ifndef LOG_TAG
-#define DBG_TAG               "drv"
+    #define DBG_TAG               "drv"
 #else
-#define DBG_TAG               LOG_TAG
+    #define DBG_TAG               LOG_TAG
 #endif /* LOG_TAG */
 
 #ifdef DRV_DEBUG
-#define DBG_LVL               DBG_LOG
+    #define DBG_LVL               DBG_LOG
 #else
-#define DBG_LVL               DBG_INFO
+    #define DBG_LVL               DBG_INFO
 #endif /* DRV_DEBUG */
 
 #include <rtdbg.h>

bsp/n32g452xx/Libraries/rt_drivers/drv_pwm.c

@@ -12,10 +12,10 @@
 #include "drv_pwm.h"
 
 #ifdef RT_USING_PWM
-#if !defined(BSP_USING_TIM3_CH1) && !defined(BSP_USING_TIM3_CH2) && \
-    !defined(BSP_USING_TIM3_CH3) && !defined(BSP_USING_TIM3_CH4)
-#error "Please define at least one BSP_USING_TIMx_CHx"
-#endif
+    #if !defined(BSP_USING_TIM3_CH1) && !defined(BSP_USING_TIM3_CH2) && \
+        !defined(BSP_USING_TIM3_CH3) && !defined(BSP_USING_TIM3_CH4)
+        #error "Please define at least one BSP_USING_TIMx_CHx"
+    #endif
 #endif /* RT_USING_PWM */
 
 #define DRV_DEBUG
@@ -28,7 +28,7 @@ struct rt_device_pwm pwm_device;
 struct n32_pwm
 {
     struct rt_device_pwm pwm_device;
-    TIM_Module* tim_handle;
+    TIM_Module *tim_handle;
     rt_uint8_t channel;
     char *name;
 };
@@ -58,45 +58,45 @@ static struct rt_pwm_ops drv_ops =
     drv_pwm_control
 };
 
-static rt_err_t drv_pwm_enable(TIM_Module* TIMx, struct rt_pwm_configuration *configuration, rt_bool_t enable)
+static rt_err_t drv_pwm_enable(TIM_Module *TIMx, struct rt_pwm_configuration *configuration, rt_bool_t enable)
 {
     /* Get the value of channel */
     rt_uint32_t channel = configuration->channel;
 
     if (!enable)
     {
-        if(channel == 1)
+        if (channel == 1)
         {
             TIM_EnableCapCmpCh(TIMx, TIM_CH_1, TIM_CAP_CMP_DISABLE);
         }
-        else if(channel == 2)
+        else if (channel == 2)
         {
             TIM_EnableCapCmpCh(TIMx, TIM_CH_2, TIM_CAP_CMP_DISABLE);
         }
-        else if(channel == 3)
+        else if (channel == 3)
         {
             TIM_EnableCapCmpCh(TIMx, TIM_CH_3, TIM_CAP_CMP_DISABLE);
         }
-        else if(channel == 4)
+        else if (channel == 4)
         {
             TIM_EnableCapCmpCh(TIMx, TIM_CH_4, TIM_CAP_CMP_DISABLE);
         }
     }
     else
     {
-        if(channel == 1)
+        if (channel == 1)
         {
             TIM_EnableCapCmpCh(TIMx, TIM_CH_1, TIM_CAP_CMP_ENABLE);
         }
-        else if(channel == 2)
+        else if (channel == 2)
         {
             TIM_EnableCapCmpCh(TIMx, TIM_CH_2, TIM_CAP_CMP_ENABLE);
         }
-        else if(channel == 3)
+        else if (channel == 3)
         {
             TIM_EnableCapCmpCh(TIMx, TIM_CH_3, TIM_CAP_CMP_ENABLE);
         }
-        else if(channel == 4)
+        else if (channel == 4)
         {
             TIM_EnableCapCmpCh(TIMx, TIM_CH_4, TIM_CAP_CMP_ENABLE);
         }
@@ -107,7 +107,7 @@ static rt_err_t drv_pwm_enable(TIM_Module* TIMx, struct rt_pwm_configuration *co
     return RT_EOK;
 }
 
-static rt_err_t drv_pwm_get(TIM_Module* TIMx, struct rt_pwm_configuration *configuration)
+static rt_err_t drv_pwm_get(TIM_Module *TIMx, struct rt_pwm_configuration *configuration)
 {
     RCC_ClocksType  RCC_Clockstruct;
     rt_uint32_t ar, div, cc1, cc2, cc3, cc4;
@@ -128,19 +128,19 @@ static rt_err_t drv_pwm_get(TIM_Module* TIMx, struct rt_pwm_configuration *confi
     /* Convert nanosecond to frequency and duty cycle. */
     tim_clock /= 1000000UL;
     configuration->period = (ar + 1) * (div + 1) * 1000UL / tim_clock;
-    if(channel == 1)
+    if (channel == 1)
         configuration->pulse = (cc1 + 1) * (div + 1) * 1000UL / tim_clock;
-    if(channel == 2)
-        configuration->pulse = (cc2 + 1) * (div+ 1) * 1000UL / tim_clock;
-    if(channel == 3)
+    if (channel == 2)
+        configuration->pulse = (cc2 + 1) * (div + 1) * 1000UL / tim_clock;
+    if (channel == 3)
         configuration->pulse = (cc3 + 1) * (div + 1) * 1000UL / tim_clock;
-    if(channel == 4)
+    if (channel == 4)
         configuration->pulse = (cc4 + 1) * (div + 1) * 1000UL / tim_clock;
 
     return RT_EOK;
 }
 
-static rt_err_t drv_pwm_set(TIM_Module* TIMx, struct rt_pwm_configuration *configuration)
+static rt_err_t drv_pwm_set(TIM_Module *TIMx, struct rt_pwm_configuration *configuration)
 {
     /* Init timer pin and enable clock */
     n32_msp_tim_init(TIMx);
@@ -155,7 +155,7 @@ static rt_err_t drv_pwm_set(TIM_Module* TIMx, struct rt_pwm_configuration *confi
     }
     else
     {
-        if (1 == (RCC_Clock.HclkFreq/RCC_Clock.Pclk1Freq))
+        if (1 == (RCC_Clock.HclkFreq / RCC_Clock.Pclk1Freq))
             input_clock = RCC_Clock.Pclk1Freq;
         else
             input_clock = RCC_Clock.Pclk1Freq * 2;
@@ -186,22 +186,22 @@ static rt_err_t drv_pwm_set(TIM_Module* TIMx, struct rt_pwm_configuration *confi
     TIM_OCInitStructure.OcPolarity = TIM_OC_POLARITY_HIGH;
 
     rt_uint32_t channel = configuration->channel;
-    if(channel == 1)
+    if (channel == 1)
     {
         TIM_InitOc1(TIMx, &TIM_OCInitStructure);
         TIM_ConfigOc1Preload(TIMx, TIM_OC_PRE_LOAD_ENABLE);
     }
-    else if(channel == 2)
+    else if (channel == 2)
     {
         TIM_InitOc2(TIMx, &TIM_OCInitStructure);
         TIM_ConfigOc2Preload(TIMx, TIM_OC_PRE_LOAD_ENABLE);
     }
-    else if(channel == 3)
+    else if (channel == 3)
     {
         TIM_InitOc3(TIMx, &TIM_OCInitStructure);
         TIM_ConfigOc3Preload(TIMx, TIM_OC_PRE_LOAD_ENABLE);
     }
-    else if(channel == 4)
+    else if (channel == 4)
     {
         TIM_InitOc4(TIMx, &TIM_OCInitStructure);
         TIM_ConfigOc4Preload(TIMx, TIM_OC_PRE_LOAD_ENABLE);
@@ -220,16 +220,16 @@ static rt_err_t drv_pwm_control(struct rt_device_pwm *device, int cmd, void *arg
 
     switch (cmd)
     {
-        case PWM_CMD_ENABLE:
-            return drv_pwm_enable(TIMx, configuration, RT_TRUE);
-        case PWM_CMD_DISABLE:
-            return drv_pwm_enable(TIMx, configuration, RT_FALSE);
-        case PWM_CMD_SET:
-            return drv_pwm_set(TIMx, configuration);
-        case PWM_CMD_GET:
-            return drv_pwm_get(TIMx, configuration);
-        default:
-            return RT_EINVAL;
+    case PWM_CMD_ENABLE:
+        return drv_pwm_enable(TIMx, configuration, RT_TRUE);
+    case PWM_CMD_DISABLE:
+        return drv_pwm_enable(TIMx, configuration, RT_FALSE);
+    case PWM_CMD_SET:
+        return drv_pwm_set(TIMx, configuration);
+    case PWM_CMD_GET:
+        return drv_pwm_get(TIMx, configuration);
+    default:
+        return RT_EINVAL;
     }
 }
 
@@ -238,9 +238,9 @@ static int rt_hw_pwm_init(void)
     int i = 0;
     int result = RT_EOK;
 
-    for(i = 0; i < sizeof(n32_pwm_obj) / sizeof(n32_pwm_obj[0]); i++)
+    for (i = 0; i < sizeof(n32_pwm_obj) / sizeof(n32_pwm_obj[0]); i++)
     {
-        if(rt_device_pwm_register(&n32_pwm_obj[i].pwm_device, n32_pwm_obj[i].name, &drv_ops, n32_pwm_obj[i].tim_handle) == RT_EOK)
+        if (rt_device_pwm_register(&n32_pwm_obj[i].pwm_device, n32_pwm_obj[i].name, &drv_ops, n32_pwm_obj[i].tim_handle) == RT_EOK)
         {
             LOG_D("%s register success", n32_pwm_obj[i].name);
         }

bsp/n32g452xx/Libraries/rt_drivers/drv_soft_i2c.c

@@ -17,8 +17,8 @@
 #include <drv_log.h>
 
 #if !defined(BSP_USING_I2C1) && !defined(BSP_USING_I2C2) && !defined(BSP_USING_I2C3) && !defined(BSP_USING_I2C4)
-#error "Please define at least one BSP_USING_I2Cx"
-/* this driver can be disabled at menuconfig → RT-Thread Components → Device Drivers */
+    #error "Please define at least one BSP_USING_I2Cx"
+    /* this driver can be disabled at menuconfig → RT-Thread Components → Device Drivers */
 #endif
 
 static const struct n32_soft_i2c_config soft_i2c_config[] =
@@ -46,7 +46,7 @@ static struct n32_i2c i2c_obj[sizeof(soft_i2c_config) / sizeof(soft_i2c_config[0
  */
 static void n32_i2c_gpio_init(struct n32_i2c *i2c)
 {
-    struct n32_soft_i2c_config* cfg = (struct n32_soft_i2c_config*)i2c->ops.data;
+    struct n32_soft_i2c_config *cfg = (struct n32_soft_i2c_config *)i2c->ops.data;
 
     rt_pin_mode(cfg->scl, PIN_MODE_OUTPUT_OD);
     rt_pin_mode(cfg->sda, PIN_MODE_OUTPUT_OD);
@@ -63,7 +63,7 @@ static void n32_i2c_gpio_init(struct n32_i2c *i2c)
  */
 static void n32_set_sda(void *data, rt_int32_t state)
 {
-    struct n32_soft_i2c_config* cfg = (struct n32_soft_i2c_config*)data;
+    struct n32_soft_i2c_config *cfg = (struct n32_soft_i2c_config *)data;
     if (state)
     {
         rt_pin_write(cfg->sda, PIN_HIGH);
@@ -82,7 +82,7 @@ static void n32_set_sda(void *data, rt_int32_t state)
  */
 static void n32_set_scl(void *data, rt_int32_t state)
 {
-    struct n32_soft_i2c_config* cfg = (struct n32_soft_i2c_config*)data;
+    struct n32_soft_i2c_config *cfg = (struct n32_soft_i2c_config *)data;
     if (state)
     {
         rt_pin_write(cfg->scl, PIN_HIGH);
@@ -100,7 +100,7 @@ static void n32_set_scl(void *data, rt_int32_t state)
  */
 static rt_int32_t n32_get_sda(void *data)
 {
-    struct n32_soft_i2c_config* cfg = (struct n32_soft_i2c_config*)data;
+    struct n32_soft_i2c_config *cfg = (struct n32_soft_i2c_config *)data;
     return rt_pin_read(cfg->sda);
 }
 
@@ -111,7 +111,7 @@ static rt_int32_t n32_get_sda(void *data)
  */
 static rt_int32_t n32_get_scl(void *data)
 {
-    struct n32_soft_i2c_config* cfg = (struct n32_soft_i2c_config*)data;
+    struct n32_soft_i2c_config *cfg = (struct n32_soft_i2c_config *)data;
     return rt_pin_read(cfg->scl);
 }
 /**
@@ -199,7 +199,7 @@ int rt_hw_i2c_init(void)
     for (int i = 0; i < obj_num; i++)
     {
         i2c_obj[i].ops = n32_bit_ops_default;
-        i2c_obj[i].ops.data = (void*)&soft_i2c_config[i];
+        i2c_obj[i].ops.data = (void *)&soft_i2c_config[i];
         i2c_obj[i].i2c_bus.priv = &i2c_obj[i].ops;
         n32_i2c_gpio_init(&i2c_obj[i]);
         result = rt_i2c_bit_add_bus(&i2c_obj[i].i2c_bus, soft_i2c_config[i].bus_name);
@@ -207,9 +207,9 @@ int rt_hw_i2c_init(void)
         n32_i2c_bus_unlock(&soft_i2c_config[i]);
 
         LOG_D("software simulation %s init done, pin scl: %d, pin sda %d",
-        soft_i2c_config[i].bus_name,
-        soft_i2c_config[i].scl,
-        soft_i2c_config[i].sda);
+              soft_i2c_config[i].bus_name,
+              soft_i2c_config[i].scl,
+              soft_i2c_config[i].sda);
     }
 
     return RT_EOK;

bsp/n32g452xx/Libraries/rt_drivers/drv_usart.c

@@ -51,7 +51,7 @@ static void DMA_Configuration(struct rt_serial_device *serial);
 
 static rt_err_t n32_uart_configure(struct rt_serial_device *serial, struct serial_configure *cfg)
 {
-    struct n32_uart* uart;
+    struct n32_uart *uart;
     USART_InitType USART_InitStructure;
 
     RT_ASSERT(serial != RT_NULL);
@@ -102,14 +102,14 @@ static rt_err_t n32_uart_configure(struct rt_serial_device *serial, struct seria
     /* Enable USART */
     USART_Enable(uart->uart_device, ENABLE);
 
-    USART_ClrFlag(uart->uart_device, USART_FLAG_TXDE|USART_FLAG_TXC);
+    USART_ClrFlag(uart->uart_device, USART_FLAG_TXDE | USART_FLAG_TXC);
 
     return RT_EOK;
 }
 
 static rt_err_t n32_uart_control(struct rt_serial_device *serial, int cmd, void *arg)
 {
-    struct n32_uart* uart;
+    struct n32_uart *uart;
     rt_uint32_t ctrl_arg = (rt_uint32_t)(arg);
 
     RT_ASSERT(serial != RT_NULL);
@@ -117,34 +117,34 @@ static rt_err_t n32_uart_control(struct rt_serial_device *serial, int cmd, void
 
     switch (cmd)
     {
+    /* disable interrupt */
+    case RT_DEVICE_CTRL_CLR_INT:
+        /* disable rx irq */
+        UART_DISABLE_IRQ(uart->irq);
         /* disable interrupt */
-        case RT_DEVICE_CTRL_CLR_INT:
-            /* disable rx irq */
-            UART_DISABLE_IRQ(uart->irq);
-            /* disable interrupt */
-            USART_ConfigInt(uart->uart_device, USART_INT_RXDNE, DISABLE);
-            break;
+        USART_ConfigInt(uart->uart_device, USART_INT_RXDNE, DISABLE);
+        break;
+    /* enable interrupt */
+    case RT_DEVICE_CTRL_SET_INT:
+        /* enable rx irq */
+        UART_ENABLE_IRQ(uart->irq);
         /* enable interrupt */
-        case RT_DEVICE_CTRL_SET_INT:
-            /* enable rx irq */
-            UART_ENABLE_IRQ(uart->irq);
-            /* enable interrupt */
-            USART_ConfigInt(uart->uart_device, USART_INT_RXDNE, ENABLE);
-            break;
-        /* USART config */
-        case RT_DEVICE_CTRL_CONFIG :
-            if (ctrl_arg == RT_DEVICE_FLAG_DMA_RX)
-            {
-                DMA_Configuration(serial);
-            }
-            break;
+        USART_ConfigInt(uart->uart_device, USART_INT_RXDNE, ENABLE);
+        break;
+    /* USART config */
+    case RT_DEVICE_CTRL_CONFIG :
+        if (ctrl_arg == RT_DEVICE_FLAG_DMA_RX)
+        {
+            DMA_Configuration(serial);
+        }
+        break;
     }
     return RT_EOK;
 }
 
 static int n32_uart_putc(struct rt_serial_device *serial, char c)
 {
-    struct n32_uart* uart;
+    struct n32_uart *uart;
 
     RT_ASSERT(serial != RT_NULL);
     uart = (struct n32_uart *)serial->parent.user_data;
@@ -171,7 +171,7 @@ static int n32_uart_putc(struct rt_serial_device *serial, char c)
 static int n32_uart_getc(struct rt_serial_device *serial)
 {
     int ch;
-    struct n32_uart* uart;
+    struct n32_uart *uart;
 
     RT_ASSERT(serial != RT_NULL);
     uart = (struct n32_uart *)serial->parent.user_data;
@@ -250,23 +250,23 @@ static void uart_isr(struct rt_serial_device *serial)
 
     RT_ASSERT(uart != RT_NULL);
 
-    if(USART_GetIntStatus(uart->uart_device, USART_INT_RXDNE) != RESET)
+    if (USART_GetIntStatus(uart->uart_device, USART_INT_RXDNE) != RESET)
     {
-        if(USART_GetFlagStatus(uart->uart_device, USART_FLAG_PEF) == RESET)
+        if (USART_GetFlagStatus(uart->uart_device, USART_FLAG_PEF) == RESET)
         {
             rt_hw_serial_isr(serial, RT_SERIAL_EVENT_RX_IND);
         }
         /* clear interrupt */
         USART_ClrIntPendingBit(uart->uart_device, USART_INT_RXDNE);
     }
-    if(USART_GetIntStatus(uart->uart_device, USART_INT_IDLEF) != RESET)
+    if (USART_GetIntStatus(uart->uart_device, USART_INT_IDLEF) != RESET)
     {
         dma_uart_rx_idle_isr(serial);
     }
     if (USART_GetIntStatus(uart->uart_device, USART_INT_TXC) != RESET)
     {
         /* clear interrupt */
-        if(serial->parent.open_flag & RT_DEVICE_FLAG_INT_TX)
+        if (serial->parent.open_flag & RT_DEVICE_FLAG_INT_TX)
         {
             rt_hw_serial_isr(serial, RT_SERIAL_EVENT_TX_DONE);
         }
@@ -443,7 +443,7 @@ void DMA2_Channel3_IRQHandler(void)
 }
 #endif /* BSP_USING_UART4 */
 
-static void NVIC_Configuration(struct n32_uart* uart)
+static void NVIC_Configuration(struct n32_uart *uart)
 {
     NVIC_InitType NVIC_InitStructure;
 
@@ -473,7 +473,7 @@ static void DMA_Configuration(struct rt_serial_device *serial)
 
     /* rx dma config */
     DMA_DeInit(uart->dma.rx_ch);
-    DMA_InitStructure.PeriphAddr = (uint32_t)&(uart->uart_device->DAT);
+    DMA_InitStructure.PeriphAddr = (uint32_t) & (uart->uart_device->DAT);
     DMA_InitStructure.MemAddr = (uint32_t)(rx_fifo->buffer);
     DMA_InitStructure.Direction = DMA_DIR_PERIPH_SRC;
     DMA_InitStructure.BufSize = serial->config.bufsz;
@@ -500,7 +500,7 @@ static void DMA_Configuration(struct rt_serial_device *serial)
 
 int rt_hw_usart_init(void)
 {
-    struct n32_uart* uart;
+    struct n32_uart *uart;
     struct serial_configure config = RT_SERIAL_CONFIG_DEFAULT;
 
 #if defined(BSP_USING_UART1)

bsp/n32g452xx/n32g452xx-mini-system/board/board.c

@@ -15,7 +15,7 @@
 #include <board.h>
 
 #ifdef BSP_USING_SRAM
-#include "drv_sram.h"
+    #include "drv_sram.h"
 #endif
 /**
   * @brief  This function is executed in case of error occurrence.

bsp/n32g452xx/n32g452xx-mini-system/board/msp/n32_msp.c

@@ -23,7 +23,7 @@ void n32_msp_usart_init(void *Instance)
     GPIO_InitStruct(&GPIO_InitCtlStruct);
     GPIO_InitCtlStruct.GPIO_Speed = GPIO_Speed_50MHz;
 #ifdef BSP_USING_UART1
-    if(USART1 == USARTx)
+    if (USART1 == USARTx)
     {
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_USART1, ENABLE);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOA, ENABLE);
@@ -37,7 +37,7 @@ void n32_msp_usart_init(void *Instance)
     }
 #endif
 #ifdef BSP_USING_UART2
-    if(USART2 == USARTx)
+    if (USART2 == USARTx)
     {
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_USART2, ENABLE);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOA, ENABLE);
@@ -51,7 +51,7 @@ void n32_msp_usart_init(void *Instance)
     }
 #endif
 #ifdef BSP_USING_UART3
-    if(USART3 == USARTx)
+    if (USART3 == USARTx)
     {
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_USART3, ENABLE);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOB, ENABLE);
@@ -65,7 +65,7 @@ void n32_msp_usart_init(void *Instance)
     }
 #endif
 #ifdef BSP_USING_UART4
-    if(UART4 == USARTx)
+    if (UART4 == USARTx)
     {
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_UART4, ENABLE);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOB, ENABLE);
@@ -91,7 +91,7 @@ void n32_msp_spi_init(void *Instance)
     GPIO_InitStruct(&GPIO_InitCtlStruct);
     GPIO_InitCtlStruct.GPIO_Speed = GPIO_Speed_50MHz;
 #ifdef BSP_USING_SPI1
-    if(SPI1 == SPIx)
+    if (SPI1 == SPIx)
     {
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_SPI1, ENABLE);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOA, ENABLE);
@@ -108,7 +108,7 @@ void n32_msp_spi_init(void *Instance)
     }
 #endif
 #ifdef BSP_USING_SPI2
-    if(SPI2 == SPIx)
+    if (SPI2 == SPIx)
     {
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_SPI2, ENABLE);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOB, ENABLE);
@@ -137,7 +137,7 @@ void n32_msp_sdio_init(void *Instance)
     GPIO_InitStruct(&GPIO_InitCtlStructure);
     GPIO_InitCtlStructure.GPIO_Speed = GPIO_Speed_50MHz;
 
-    if(SDIO == SDIOx)
+    if (SDIO == SDIOx)
     {
         /* if used dma ... */
         RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_DMA2, ENABLE);
@@ -162,7 +162,7 @@ void n32_msp_tim_init(void *Instance)
     GPIO_InitStruct(&GPIO_InitCtlStructure);
     TIM_Module *TIMx = (TIM_Module *)Instance;
 
-    if(TIMx == TIM1)
+    if (TIMx == TIM1)
     {
         /* TIM1 clock enable */
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_TIM1, ENABLE);
@@ -177,7 +177,7 @@ void n32_msp_tim_init(void *Instance)
         GPIO_InitPeripheral(GPIOA, &GPIO_InitCtlStructure);
     }
 
-    if(TIMx == TIM2)
+    if (TIMx == TIM2)
     {
         /* TIM2 clock enable */
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM2, ENABLE);
@@ -192,12 +192,12 @@ void n32_msp_tim_init(void *Instance)
         GPIO_InitPeripheral(GPIOA, &GPIO_InitCtlStructure);
     }
 
-    if(TIMx == TIM3)
+    if (TIMx == TIM3)
     {
         /* TIM3 clock enable */
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM3, ENABLE);
         /* GPIOA clock enable */
-        RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOA|RCC_APB2_PERIPH_GPIOB, ENABLE);
+        RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOA | RCC_APB2_PERIPH_GPIOB, ENABLE);
 
         GPIO_InitCtlStructure.Pin = GPIO_PIN_6 | GPIO_PIN_7;
         GPIO_InitCtlStructure.GPIO_Mode = GPIO_Mode_AF_PP;
@@ -218,15 +218,15 @@ void n32_msp_adc_init(void *Instance)
     ADC_Module *ADCx = (ADC_Module *)Instance;
 
 #ifdef BSP_USING_ADC1
-    if(ADCx == ADC1)
+    if (ADCx == ADC1)
     {
         /* ADC1 & GPIO clock enable */
         RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_ADC1, ENABLE);
-        ADC_ConfigClk(ADC_CTRL3_CKMOD_AHB,RCC_ADCHCLK_DIV8);
+        ADC_ConfigClk(ADC_CTRL3_CKMOD_AHB, RCC_ADCHCLK_DIV8);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOC, ENABLE);
 
         /* Configure ADC Channel as analog input */
-        GPIO_InitCtlStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3;
+        GPIO_InitCtlStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3;
         GPIO_InitCtlStruct.GPIO_Speed = GPIO_Speed_2MHz;
         GPIO_InitCtlStruct.GPIO_Mode = GPIO_Mode_AIN;
         GPIO_InitPeripheral(GPIOC, &GPIO_InitCtlStruct);
@@ -234,11 +234,11 @@ void n32_msp_adc_init(void *Instance)
 #endif
 
 #ifdef BSP_USING_ADC2
-    if(ADCx == ADC2)
+    if (ADCx == ADC2)
     {
         /* ADC2 & GPIO clock enable */
         RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_ADC2, ENABLE);
-        ADC_ConfigClk(ADC_CTRL3_CKMOD_AHB,RCC_ADCHCLK_DIV8);
+        ADC_ConfigClk(ADC_CTRL3_CKMOD_AHB, RCC_ADCHCLK_DIV8);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOC, ENABLE);
 
         /* Configure ADC Channel as analog input */
@@ -257,7 +257,7 @@ void n32_msp_hwtim_init(void *Instance)
     TIM_Module *TIMx = (TIM_Module *)Instance;
 
 #ifdef BSP_USING_HWTIM3
-    if(TIMx == TIM3)
+    if (TIMx == TIM3)
     {
         /* TIM3 clock enable */
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM3, ENABLE);
@@ -265,7 +265,7 @@ void n32_msp_hwtim_init(void *Instance)
 #endif
 
 #ifdef BSP_USING_HWTIM4
-    if(TIMx == TIM4)
+    if (TIMx == TIM4)
     {
         /* TIM4 clock enable */
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM4, ENABLE);
@@ -273,7 +273,7 @@ void n32_msp_hwtim_init(void *Instance)
 #endif
 
 #ifdef BSP_USING_HWTIM5
-    if(TIMx == TIM5)
+    if (TIMx == TIM5)
     {
         /* TIM5 clock enable */
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM5, ENABLE);
@@ -281,19 +281,19 @@ void n32_msp_hwtim_init(void *Instance)
 #endif
 
 #ifdef BSP_USING_HWTIM6
-        if(TIMx == TIM6)
-        {
-            /* TIM6 clock enable */
-            RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM6, ENABLE);
-        }
+    if (TIMx == TIM6)
+    {
+        /* TIM6 clock enable */
+        RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM6, ENABLE);
+    }
 #endif
 
 #ifdef BSP_USING_HWTIM7
-        if(TIMx == TIM7)
-        {
-            /* TIM7 clock enable */
-            RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM7, ENABLE);
-        }
+    if (TIMx == TIM7)
+    {
+        /* TIM7 clock enable */
+        RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_TIM7, ENABLE);
+    }
 #endif
 }
 #endif
@@ -307,7 +307,7 @@ void n32_msp_can_init(void *Instance)
     GPIO_InitStruct(&GPIO_InitCtlStruct);
     GPIO_InitCtlStruct.GPIO_Speed = GPIO_Speed_50MHz;
 #ifdef BSP_USING_CAN1
-    if(CAN1 == CANx)
+    if (CAN1 == CANx)
     {
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_CAN1, ENABLE);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOA, ENABLE);
@@ -321,7 +321,7 @@ void n32_msp_can_init(void *Instance)
     }
 #endif
 #ifdef BSP_USING_CAN2
-    if(CAN2 == CANx)
+    if (CAN2 == CANx)
     {
         RCC_EnableAPB1PeriphClk(RCC_APB1_PERIPH_CAN2, ENABLE);
         RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_AFIO, ENABLE);
@@ -347,7 +347,7 @@ static void uart_test_rw(rt_device_t uartx, const char *name)
     if (uartx == NULL)
     {
         uartx = rt_device_find(name);
-        rt_err_t err = rt_device_open(uartx, RT_DEVICE_FLAG_INT_RX|RT_DEVICE_FLAG_DMA_RX);
+        rt_err_t err = rt_device_open(uartx, RT_DEVICE_FLAG_INT_RX | RT_DEVICE_FLAG_DMA_RX);
         RT_ASSERT(err == RT_EOK);
     }
     rt_device_write(uartx, 0, name, strlen(name));
@@ -356,7 +356,7 @@ static void uart_test_rw(rt_device_t uartx, const char *name)
     int ret = rt_device_read(uartx, 0, recv_buf, sizeof(recv_buf));
     if (ret != 0)
     {
-        for (int i=0; i<ret; ++i)
+        for (int i = 0; i < ret; ++i)
             rt_kprintf("[%02x]", recv_buf[i]);
     }
     rt_device_write(uartx, 0, "\r\n", 2);
@@ -377,9 +377,9 @@ MSH_CMD_EXPORT(uart_test, uart_test)
 
 #ifdef BSP_USING_ADC
 #ifdef BSP_USING_ADC1
-#define ADC_DEV_NAME        "adc1"
+    #define ADC_DEV_NAME        "adc1"
 #else
-#define ADC_DEV_NAME        "adc2"
+    #define ADC_DEV_NAME        "adc2"
 #endif
 #define REFER_VOLTAGE       3300
 #define CONVERT_BITS        (1 << 12)
@@ -396,7 +396,7 @@ static int adc_vol_sample(int argc, char *argv[])
         return RT_ERROR;
     }
 
-    for (int i=6; i<=9; ++i)
+    for (int i = 6; i <= 9; ++i)
     {
         ret = rt_adc_enable(adc_dev, i);
         value = rt_adc_read(adc_dev, i);

bsp/n32g452xx/n32g452xx-mini-system/project.uvprojx

@@ -390,9 +390,9 @@
           <GroupName>CPU</GroupName>
           <Files>
             <File>
-              <FileName>backtrace.c</FileName>
+              <FileName>showmem.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\libcpu\arm\common\backtrace.c</FilePath>
+              <FilePath>..\..\..\libcpu\arm\common\showmem.c</FilePath>
             </File>
           </Files>
           <Files>
@@ -404,9 +404,9 @@
           </Files>
           <Files>
             <File>
-              <FileName>showmem.c</FileName>
+              <FileName>backtrace.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\libcpu\arm\common\showmem.c</FilePath>
+              <FilePath>..\..\..\libcpu\arm\common\backtrace.c</FilePath>
             </File>
           </Files>
           <Files>
@@ -449,30 +449,30 @@
           </Files>
           <Files>
             <File>
-              <FileName>workqueue.c</FileName>
+              <FileName>pipe.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\components\drivers\src\workqueue.c</FilePath>
+              <FilePath>..\..\..\components\drivers\src\pipe.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>waitqueue.c</FileName>
+              <FileName>ringbuffer.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\components\drivers\src\waitqueue.c</FilePath>
+              <FilePath>..\..\..\components\drivers\src\ringbuffer.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>pipe.c</FileName>
+              <FileName>completion.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\components\drivers\src\pipe.c</FilePath>
+              <FilePath>..\..\..\components\drivers\src\completion.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>completion.c</FileName>
+              <FileName>ringblk_buf.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\components\drivers\src\completion.c</FilePath>
+              <FilePath>..\..\..\components\drivers\src\ringblk_buf.c</FilePath>
             </File>
           </Files>
           <Files>
@@ -484,16 +484,16 @@
           </Files>
           <Files>
             <File>
-              <FileName>ringblk_buf.c</FileName>
+              <FileName>workqueue.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\components\drivers\src\ringblk_buf.c</FilePath>
+              <FilePath>..\..\..\components\drivers\src\workqueue.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>ringbuffer.c</FileName>
+              <FileName>waitqueue.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\components\drivers\src\ringbuffer.c</FilePath>
+              <FilePath>..\..\..\components\drivers\src\waitqueue.c</FilePath>
             </File>
           </Files>
         </Group>
@@ -508,16 +508,16 @@
           </Files>
           <Files>
             <File>
-              <FileName>startup_n32g45x.s</FileName>
-              <FileType>2</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\CMSIS\device\startup\startup_n32g45x.s</FilePath>
+              <FileName>board.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>board\board.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>board.c</FileName>
-              <FileType>1</FileType>
-              <FilePath>board\board.c</FilePath>
+              <FileName>startup_n32g45x.s</FileName>
+              <FileType>2</FileType>
+              <FilePath>..\Libraries\N32_Std_Driver\CMSIS\device\startup\startup_n32g45x.s</FilePath>
             </File>
           </Files>
           <Files>
@@ -577,98 +577,105 @@
           <GroupName>Kernel</GroupName>
           <Files>
             <File>
-              <FileName>clock.c</FileName>
+              <FileName>irq.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\clock.c</FilePath>
+              <FilePath>..\..\..\src\irq.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>thread.c</FileName>
+              <FileName>mempool.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\thread.c</FilePath>
+              <FilePath>..\..\..\src\mempool.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>mempool.c</FileName>
+              <FileName>ipc.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\mempool.c</FilePath>
+              <FilePath>..\..\..\src\ipc.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>scheduler.c</FileName>
+              <FileName>clock.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\scheduler.c</FilePath>
+              <FilePath>..\..\..\src\clock.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>device.c</FileName>
+              <FileName>object.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\device.c</FilePath>
+              <FilePath>..\..\..\src\object.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>idle.c</FileName>
+              <FileName>timer.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\idle.c</FilePath>
+              <FilePath>..\..\..\src\timer.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>ipc.c</FileName>
+              <FileName>scheduler.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\ipc.c</FilePath>
+              <FilePath>..\..\..\src\scheduler.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>timer.c</FileName>
+              <FileName>device.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\timer.c</FilePath>
+              <FilePath>..\..\..\src\device.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>mem.c</FileName>
+              <FileName>thread.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\mem.c</FilePath>
+              <FilePath>..\..\..\src\thread.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>irq.c</FileName>
+              <FileName>components.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\irq.c</FilePath>
+              <FilePath>..\..\..\src\components.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>object.c</FileName>
+              <FileName>kservice.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\object.c</FilePath>
+              <FilePath>..\..\..\src\kservice.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>components.c</FileName>
+              <FileName>idle.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\components.c</FilePath>
+              <FilePath>..\..\..\src\idle.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>kservice.c</FileName>
+              <FileName>mem.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\src\kservice.c</FilePath>
+              <FilePath>..\..\..\src\mem.c</FilePath>
             </File>
           </Files>
         </Group>
         <Group>
           <GroupName>libc</GroupName>
+          <Files>
+            <File>
+              <FileName>libc.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\libc\compilers\armlibc\libc.c</FilePath>
+            </File>
+          </Files>
           <Files>
             <File>
               <FileName>syscalls.c</FileName>
@@ -685,9 +692,9 @@
           </Files>
           <Files>
             <File>
-              <FileName>libc.c</FileName>
+              <FileName>time.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\..\components\libc\compilers\armlibc\libc.c</FilePath>
+              <FilePath>..\..\..\components\libc\compilers\common\time.c</FilePath>
             </File>
           </Files>
           <Files>
@@ -697,35 +704,28 @@
               <FilePath>..\..\..\components\libc\compilers\common\stdlib.c</FilePath>
             </File>
           </Files>
-          <Files>
-            <File>
-              <FileName>time.c</FileName>
-              <FileType>1</FileType>
-              <FilePath>..\..\..\components\libc\compilers\common\time.c</FilePath>
-            </File>
-          </Files>
         </Group>
         <Group>
           <GroupName>Libraries</GroupName>
           <Files>
             <File>
-              <FileName>n32g45x_rtc.c</FileName>
+              <FileName>n32g45x_wwdg.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_rtc.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_wwdg.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_qspi.c</FileName>
+              <FileName>n32g45x_adc.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_qspi.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_adc.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_sdio.c</FileName>
+              <FileName>n32g45x_comp.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_sdio.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_comp.c</FilePath>
             </File>
           </Files>
           <Files>
@@ -737,177 +737,178 @@
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_bkp.c</FileName>
+              <FileName>n32g45x_i2c.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_bkp.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_i2c.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_dma.c</FileName>
+              <FileName>n32g45x_gpio.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_dma.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_gpio.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_usart.c</FileName>
+              <FileName>n32g45x_pwr.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_usart.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_pwr.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_adc.c</FileName>
+              <FileName>n32g45x_flash.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_adc.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_flash.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_dvp.c</FileName>
+              <FileName>n32g45x_spi.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_dvp.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_spi.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_opamp.c</FileName>
+              <FileName>n32g45x_exti.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_opamp.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_exti.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>misc.c</FileName>
+              <FileName>n32g45x_xfmc.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\misc.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_xfmc.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_spi.c</FileName>
+              <FileName>n32g45x_rtc.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_spi.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_rtc.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_dac.c</FileName>
+              <FileName>n32g45x_crc.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_dac.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_crc.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_exti.c</FileName>
+              <FileName>n32g45x_iwdg.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_exti.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_iwdg.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_gpio.c</FileName>
+              <FileName>n32g45x_qspi.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_gpio.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_qspi.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_xfmc.c</FileName>
+              <FileName>n32g45x_tsc.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_xfmc.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_tsc.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_can.c</FileName>
+              <FileName>n32g45x_opamp.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_can.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_opamp.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_pwr.c</FileName>
+              <FileName>n32g45x_tim.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_pwr.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_tim.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_i2c.c</FileName>
+              <FileName>n32g45x_bkp.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_i2c.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_bkp.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_wwdg.c</FileName>
+              <FileName>n32g45x_dma.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_wwdg.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_dma.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_dbg.c</FileName>
+              <FileName>n32g45x_rcc.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_dbg.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_rcc.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_tim.c</FileName>
+              <FileName>n32g45x_usart.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_tim.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_usart.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_crc.c</FileName>
+              <FileName>system_n32g45x.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_crc.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\CMSIS\device\system_n32g45x.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_tsc.c</FileName>
+              <FileName>n32g45x_dvp.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_tsc.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_dvp.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_iwdg.c</FileName>
+              <FileName>n32g45x_can.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_iwdg.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_can.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_rcc.c</FileName>
+              <FileName>n32g45x_dbg.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_rcc.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_dbg.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>system_n32g45x.c</FileName>
+              <FileName>misc.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\CMSIS\device\system_n32g45x.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\misc.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_comp.c</FileName>
+              <FileName>n32g45x_dac.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_comp.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_dac.c</FilePath>
             </File>
           </Files>
           <Files>
             <File>
-              <FileName>n32g45x_flash.c</FileName>
+              <FileName>n32g45x_sdio.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_flash.c</FilePath>
+              <FilePath>..\Libraries\N32_Std_Driver\n32g45x_std_periph_driver\src\n32g45x_sdio.c</FilePath>
+
             </File>
           </Files>
         </Group>