modify mini2440/board.c serial device

modify s3c24x0/clock.c clock initialization

git-svn-id: https://rt-thread.googlecode.com/svn/trunk@225 bbd45198-f89e-11dd-88c7-29a3b14d5316

bsp/mini2440/board.c

@@ -28,7 +28,8 @@
 extern rt_uint32_t PCLK, FCLK, HCLK, UCLK;
 extern rt_uint8_t asc16_font[];
 extern rt_uint16_t _rt_hw_framebuffer[];
-
+
+extern void rt_hw_clock_init(void);
 extern void rt_hw_lcd_init(void);
 extern void rt_hw_mmu_init(void);
 extern void rt_hw_touch_init(void);
@@ -84,10 +85,10 @@ void rt_serial_handler(int vector)
 void rt_hw_uart_init(void)
 {
 	int i;
-
-	GPHCON |= 0xa0;
-	/*PULLUP is enable */
-	GPHUP  |= 0x0c;
+	/* UART0 port configure */
+	GPHCON |= 0xAA;
+	/* PULLUP is disable */
+	GPHUP |= 0xF;
 
 	/* FIFO enable, Tx/Rx FIFO clear */
 	uart0.uart_device->ufcon = 0x1;
@@ -99,8 +100,9 @@ void rt_hw_uart_init(void)
 	 * tx=level,rx=edge,disable timeout int.,enable rx error int.,
 	 * normal,interrupt or polling
 	 */
-	uart0.uart_device->ucon = 0x245;
-
+	uart0.uart_device->ucon = 0x245;
+	/* Set uart0 bps */
+	uart0.uart_device->ubrd = (rt_int32_t)(PCLK / (BPS * 16)) - 1;
 	/* output PCLK to UART0/1, PWMTIMER */
 	CLKCON |= 0x0D00;
 
@@ -117,42 +119,12 @@ void rt_hw_uart_init(void)
  * This function will init s3ceb2410 board
  */
 void rt_hw_board_init()
-{
-	/* FCLK = 304.8M */
-	#define MDIV		68
-	#define PDIV		1
-	#define SDIV		1
-
-	//rt_hw_set_clock(SDIV, PDIV, MDIV);
-	/* HCLK = PCLK = FCLK */
-	//rt_hw_set_dividor(0, 0);
-
-	/* use PWM Timer 4 because it has no output */
-	/* prescaler for Timer 4 is 16 */
-	TCFG0 = 0x0f00;
-
-	/* all divider = 1/2 */
-	TCFG1 = 0x0;
-
-	rt_hw_get_clock();
-
-	if (timer_load_val == 0)
-	{
-		/*
-		 * for 10 ms clock period @ PCLK with 4 bit divider = 1/2
-		 * (default) and prescaler = 16. Should be 10390
-		 * @33.25MHz and 15625 @ 50 MHz
-		 */
-		timer_load_val = PCLK/(2 * 16 * 100);
-	}
-	/* load value for 10 ms timeout */
-	TCNTB4 = timer_load_val;
-	/* auto load, manual update of Timer 4 */
-	TCON = (TCON & ~0x0700000) | 0x600000;
-	/* auto load, start Timer 4 */
-	TCON = (TCON & ~0x0700000) | 0x500000 | 0x3;
-	/*Enable NAND, USBD, PWM TImer, UART0,1 and GPIO clock,*/
-	CLKCON = 0xfffff0;
+{
+	/* initialize the system clock */
+	rt_hw_clock_init();
+
+	/* Get the clock */
+	rt_hw_get_clock();
 
 	/* initialize uart */
 	rt_hw_uart_init();

libcpu/arm/s3c24x0/clock.c

@@ -17,6 +17,21 @@
 
 #define CONFIG_SYS_CLK_FREQ	12000000	// Fin = 12.00MHz
 
+#if CONFIG_SYS_CLK_FREQ == 12000000
+	/* MPLL=2*12*100/6=400MHz	*/
+	#define 	MPL_MIDV	92		/* m=MPL_MDIV+8=100 */
+	#define 	MPL_PDIV	4		/* p=MPL_PDIV+2=6	*/
+	#define 	MPL_SDIV	0		/* s=MPL_SDIV=0 */
+	/* UPLL=12*64/8=96MHz */	
+	#define 	UPL_MDIV	56		/* m=UPL_MDIV+8=64 */		
+	#define 	UPL_PDIV	2		/* p=UPL_PDIV+2=4	*/
+	#define 	UPL_SDIV	1		/* s=UPL_SDIV=1 */
+	/* System clock divider FCLK:HCLK:PCLK=1:4:8 */
+	#define 	DIVN_UPLL		0x1 	/* UCLK = UPLL clock / 2 */
+	#define 	HDIVN			0x2 	/* HCLK = FCLK / 4 */
+	#define 	PDIVN			0x1 	/* PCLK = HCLK / 2 */
+#endif
+
 rt_uint32_t PCLK;
 rt_uint32_t FCLK;
 rt_uint32_t HCLK;
@@ -65,13 +80,29 @@ void rt_hw_get_clock(void)
 		PCLK = HCLK;
 }
 
-void rt_hw_set_clock(rt_uint8_t sdiv, rt_uint8_t pdiv, rt_uint8_t mdiv)
+void rt_hw_set_mpll_clock(rt_uint8_t sdiv, rt_uint8_t pdiv, rt_uint8_t mdiv)
+{
+	MPLLCON = sdiv | (pdiv<<4) | (mdiv<<12);
+}
+
+void rt_hw_set_upll_clock(rt_uint8_t sdiv, rt_uint8_t pdiv, rt_uint8_t mdiv)
 {
-	MPLLCON = sdiv | pdiv<<4 | mdiv<<12;
+	UPLLCON = (mdiv<<12) | (pdiv<<4) | sdiv;
 }
 
-void rt_hw_set_dividor(rt_uint8_t hdivn, rt_uint8_t pdivn)
+void rt_hw_set_divider(rt_uint8_t hdivn, rt_uint8_t pdivn)
 {
 	CLKDIVN = (hdivn<<1) | pdivn;
 }
 
+/**
+ * @brief System Clock Configuration
+ */
+void rt_hw_clock_init(void)
+{
+	LOCKTIME = 0xFFFFFFFF;
+	rt_hw_set_divider(HDIVN, PDIVN);
+	rt_hw_set_upll_clock(UPL_SDIV, UPL_PDIV, UPL_MDIV);
+	rt_hw_set_mpll_clock(MPL_SDIV, MPL_PDIV, MPL_MIDV);
+}
+