[add][RT1060]修正上手指南 (#7207)

* [add]修正上手指南

* [add]修正上手指南与重新配置rtconfig.h

bsp/imxrt/imxrt1060-nxp-evk/.config

@@ -73,7 +73,7 @@ CONFIG_RT_USING_DEVICE=y
 CONFIG_RT_USING_CONSOLE=y
 CONFIG_RT_CONSOLEBUF_SIZE=128
 CONFIG_RT_CONSOLE_DEVICE_NAME="uart1"
-CONFIG_RT_VER_NUM=0x50000
+CONFIG_RT_VER_NUM=0x50001
 # CONFIG_RT_USING_STDC_ATOMIC is not set
 CONFIG_RT_USING_CACHE=y
 CONFIG_RT_USING_HW_ATOMIC=y
@@ -108,41 +108,11 @@ CONFIG_FINSH_USING_DESCRIPTION=y
 # CONFIG_FINSH_ECHO_DISABLE_DEFAULT is not set
 # CONFIG_FINSH_USING_AUTH is not set
 CONFIG_FINSH_ARG_MAX=10
-CONFIG_RT_USING_DFS=y
-CONFIG_DFS_USING_POSIX=y
-CONFIG_DFS_USING_WORKDIR=y
-CONFIG_DFS_FILESYSTEMS_MAX=4
-CONFIG_DFS_FILESYSTEM_TYPES_MAX=4
-CONFIG_DFS_FD_MAX=16
-# CONFIG_RT_USING_DFS_MNTTABLE is not set
-CONFIG_RT_USING_DFS_ELMFAT=y
 
 #
-# elm-chan's FatFs, Generic FAT Filesystem Module
-#
-CONFIG_RT_DFS_ELM_CODE_PAGE=437
-CONFIG_RT_DFS_ELM_WORD_ACCESS=y
-# CONFIG_RT_DFS_ELM_USE_LFN_0 is not set
-# CONFIG_RT_DFS_ELM_USE_LFN_1 is not set
-# CONFIG_RT_DFS_ELM_USE_LFN_2 is not set
-CONFIG_RT_DFS_ELM_USE_LFN_3=y
-CONFIG_RT_DFS_ELM_USE_LFN=3
-CONFIG_RT_DFS_ELM_LFN_UNICODE_0=y
-# CONFIG_RT_DFS_ELM_LFN_UNICODE_1 is not set
-# CONFIG_RT_DFS_ELM_LFN_UNICODE_2 is not set
-# CONFIG_RT_DFS_ELM_LFN_UNICODE_3 is not set
-CONFIG_RT_DFS_ELM_LFN_UNICODE=0
-CONFIG_RT_DFS_ELM_MAX_LFN=255
-CONFIG_RT_DFS_ELM_DRIVES=2
-CONFIG_RT_DFS_ELM_MAX_SECTOR_SIZE=512
-# CONFIG_RT_DFS_ELM_USE_ERASE is not set
-CONFIG_RT_DFS_ELM_REENTRANT=y
-CONFIG_RT_DFS_ELM_MUTEX_TIMEOUT=3000
-CONFIG_RT_USING_DFS_DEVFS=y
-# CONFIG_RT_USING_DFS_ROMFS is not set
-# CONFIG_RT_USING_DFS_CROMFS is not set
-# CONFIG_RT_USING_DFS_RAMFS is not set
-# CONFIG_RT_USING_DFS_TMPFS is not set
+# DFS: device virtual file system
+#
+# CONFIG_RT_USING_DFS is not set
 # CONFIG_RT_USING_FAL is not set
 
 #
@@ -193,13 +163,9 @@ CONFIG_RT_USING_PIN=y
 #
 # Using USB
 #
-CONFIG_RT_USING_USB=y
-CONFIG_RT_USING_USB_HOST=y
-CONFIG_RT_USBH_MSTORAGE=y
-CONFIG_UDISK_MOUNTPOINT="/"
-# CONFIG_RT_USBH_HID is not set
+# CONFIG_RT_USING_USB is not set
+# CONFIG_RT_USING_USB_HOST is not set
 # CONFIG_RT_USING_USB_DEVICE is not set
-CONFIG_RT_USBD_THREAD_STACK_SZ=4096
 
 #
 # C/C++ and POSIX layer
@@ -232,15 +198,7 @@ CONFIG_RT_LIBC_DEFAULT_TIMEZONE=8
 # Network
 #
 # CONFIG_RT_USING_SAL is not set
-CONFIG_RT_USING_NETDEV=y
-CONFIG_NETDEV_USING_IFCONFIG=y
-CONFIG_NETDEV_USING_PING=y
-CONFIG_NETDEV_USING_NETSTAT=y
-CONFIG_NETDEV_USING_AUTO_DEFAULT=y
-# CONFIG_NETDEV_USING_IPV6 is not set
-CONFIG_NETDEV_IPV4=1
-CONFIG_NETDEV_IPV6=0
-# CONFIG_NETDEV_IPV6_SCOPES is not set
+# CONFIG_RT_USING_NETDEV is not set
 # CONFIG_RT_USING_LWIP is not set
 # CONFIG_RT_USING_AT is not set
 
@@ -347,7 +305,6 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_EMBEDDEDPROTO is not set
 # CONFIG_PKG_USING_RT_LINK_HW is not set
 # CONFIG_PKG_USING_RYANMQTT is not set
-# CONFIG_PKG_USING_RYANW5500 is not set
 # CONFIG_PKG_USING_LORA_PKT_FWD is not set
 # CONFIG_PKG_USING_LORA_GW_DRIVER_LIB is not set
 # CONFIG_PKG_USING_LORA_PKT_SNIFFER is not set
@@ -356,7 +313,6 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_NET_SERVER is not set
 # CONFIG_PKG_USING_ZFTP is not set
 # CONFIG_PKG_USING_WOL is not set
-# CONFIG_PKG_USING_ZEPHYR_POLLING is not set
 
 #
 # security packages
@@ -425,13 +381,18 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_MP3PLAYER is not set
 # CONFIG_PKG_USING_TINYJPEG is not set
 # CONFIG_PKG_USING_UGUI is not set
+
+#
+# PainterEngine: A cross-platform graphics application framework written in C language
+#
+# CONFIG_PKG_USING_PAINTERENGINE is not set
+# CONFIG_PKG_USING_PAINTERENGINE_AUX is not set
 # CONFIG_PKG_USING_MCURSES is not set
 # CONFIG_PKG_USING_TERMBOX is not set
 # CONFIG_PKG_USING_VT100 is not set
 # CONFIG_PKG_USING_QRCODE is not set
 # CONFIG_PKG_USING_GUIENGINE is not set
 # CONFIG_PKG_USING_PERSIMMON is not set
-# CONFIG_PKG_USING_3GPP_AMRNB is not set
 
 #
 # tools packages
@@ -441,7 +402,6 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_EASYLOGGER is not set
 # CONFIG_PKG_USING_SYSTEMVIEW is not set
 # CONFIG_PKG_USING_SEGGER_RTT is not set
-# CONFIG_PKG_USING_RTT_AUTO_EXE_CMD is not set
 # CONFIG_PKG_USING_RDB is not set
 # CONFIG_PKG_USING_ULOG_EASYFLASH is not set
 # CONFIG_PKG_USING_LOGMGR is not set
@@ -549,7 +509,6 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_TFDB is not set
 # CONFIG_PKG_USING_QPC is not set
 # CONFIG_PKG_USING_AGILE_UPGRADE is not set
-# CONFIG_PKG_USING_FLASH_BLOB is not set
 
 #
 # peripheral libraries and drivers
@@ -558,6 +517,7 @@ CONFIG_NETDEV_IPV6=0
 #
 # sensors drivers
 #
+# CONFIG_PKG_USING_FINGERPRINT is not set
 # CONFIG_PKG_USING_LSM6DSM is not set
 # CONFIG_PKG_USING_LSM6DSL is not set
 # CONFIG_PKG_USING_LPS22HB is not set
@@ -617,11 +577,6 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_AD7746 is not set
 # CONFIG_PKG_USING_ADT74XX is not set
 # CONFIG_PKG_USING_MAX17048 is not set
-# CONFIG_PKG_USING_AS7341 is not set
-# CONFIG_PKG_USING_CW2015 is not set
-# CONFIG_PKG_USING_ICM20608 is not set
-# CONFIG_PKG_USING_PAJ7620 is not set
-# CONFIG_PKG_USING_STHS34PF80 is not set
 
 #
 # touch drivers
@@ -635,8 +590,10 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_FT6236 is not set
 # CONFIG_PKG_USING_XPT2046_TOUCH is not set
 # CONFIG_PKG_USING_REALTEK_AMEBA is not set
+# CONFIG_PKG_USING_AS7341 is not set
 # CONFIG_PKG_USING_STM32_SDIO is not set
 # CONFIG_PKG_USING_ESP_IDF is not set
+# CONFIG_PKG_USING_ICM20608 is not set
 # CONFIG_PKG_USING_BUTTON is not set
 # CONFIG_PKG_USING_PCF8574 is not set
 # CONFIG_PKG_USING_SX12XX is not set
@@ -660,7 +617,6 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_AT24CXX is not set
 # CONFIG_PKG_USING_MOTIONDRIVER2RTT is not set
 # CONFIG_PKG_USING_PCA9685 is not set
-# CONFIG_PKG_USING_ILI9341 is not set
 # CONFIG_PKG_USING_I2C_TOOLS is not set
 # CONFIG_PKG_USING_NRF24L01 is not set
 # CONFIG_PKG_USING_RPLIDAR is not set
@@ -677,6 +633,7 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_CAN_YMODEM is not set
 # CONFIG_PKG_USING_LORA_RADIO_DRIVER is not set
 # CONFIG_PKG_USING_QLED is not set
+# CONFIG_PKG_USING_PAJ7620 is not set
 # CONFIG_PKG_USING_AGILE_CONSOLE is not set
 # CONFIG_PKG_USING_LD3320 is not set
 # CONFIG_PKG_USING_WK2124 is not set
@@ -707,11 +664,11 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_BL_MCU_SDK is not set
 # CONFIG_PKG_USING_SOFT_SERIAL is not set
 # CONFIG_PKG_USING_MB85RS16 is not set
+# CONFIG_PKG_USING_CW2015 is not set
 # CONFIG_PKG_USING_RFM300 is not set
 # CONFIG_PKG_USING_IO_INPUT_FILTER is not set
 # CONFIG_PKG_USING_RASPBERRYPI_PICO_SDK is not set
 # CONFIG_PKG_USING_LRF_NV7LIDAR is not set
-# CONFIG_PKG_USING_FINGERPRINT is not set
 
 #
 # AI packages
@@ -761,7 +718,6 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_TETRIS is not set
 # CONFIG_PKG_USING_DONUT is not set
 # CONFIG_PKG_USING_COWSAY is not set
-# CONFIG_PKG_USING_MORSE is not set
 # CONFIG_PKG_USING_LIBCSV is not set
 # CONFIG_PKG_USING_OPTPARSE is not set
 # CONFIG_PKG_USING_FASTLZ is not set
@@ -951,7 +907,6 @@ CONFIG_NETDEV_IPV6=0
 # Display
 #
 # CONFIG_PKG_USING_ARDUINO_U8G2 is not set
-# CONFIG_PKG_USING_ARDUINO_U8GLIB_ARDUINO is not set
 # CONFIG_PKG_USING_SEEED_TM1637 is not set
 
 #
@@ -981,17 +936,10 @@ CONFIG_NETDEV_IPV6=0
 # CONFIG_PKG_USING_ARDUINO_ADAFRUIT_PCF8574 is not set
 # CONFIG_PKG_USING_ARDUINO_ADAFRUIT_PCA9685 is not set
 # CONFIG_PKG_USING_ARDUINO_SEEED_PCF85063TP is not set
-# CONFIG_PKG_USING_ARDUINO_ADAFRUIT_TPA2016 is not set
-# CONFIG_PKG_USING_ARDUINO_ADAFRUIT_DRV2605 is not set
-# CONFIG_PKG_USING_ARDUINO_ADAFRUIT_DS1841 is not set
-# CONFIG_PKG_USING_ARDUINO_ADAFRUIT_DS3502 is not set
 
 #
 # Other
 #
-# CONFIG_PKG_USING_ARDUINO_ADAFRUIT_MFRC630 is not set
-# CONFIG_PKG_USING_ARDUINO_ADAFRUIT_SI5351 is not set
-# CONFIG_PKG_USING_ARDUINO_RTCLIB is not set
 
 #
 # Signal IO
@@ -1020,7 +968,7 @@ CONFIG_SOC_MIMXRT1062DVL6A=y
 #
 # Onboard Peripheral Drivers
 #
-CONFIG_BSP_USING_SDRAM=y
+# CONFIG_BSP_USING_SDRAM is not set
 # CONFIG_BSP_USING_ETH is not set
 # CONFIG_BSP_USING_LCD is not set
 # CONFIG_BSP_USING_TOUCHPAD is not set
@@ -1030,12 +978,11 @@ CONFIG_BSP_USING_SDRAM=y
 #
 # On-chip Peripheral Drivers
 #
+# CONFIG_BSP_USING_DMA is not set
 CONFIG_BSP_USING_GPIO=y
 # CONFIG_BSP_USING_RTC is not set
 # CONFIG_BSP_USING_SDIO is not set
-CONFIG_BSP_USING_USB=y
-CONFIG_BSP_USB0_HOST=y
-# CONFIG_BSP_USB1_HOST is not set
+# CONFIG_BSP_USING_USB is not set
 # CONFIG_BSP_USING_I2C is not set
 CONFIG_BSP_USING_LPUART=y
 CONFIG_BSP_USING_LPUART1=y
@@ -1046,8 +993,9 @@ CONFIG_BSP_USING_LPUART1=y
 # CONFIG_BSP_USING_LPUART6 is not set
 # CONFIG_BSP_USING_LPUART7 is not set
 # CONFIG_BSP_USING_LPUART8 is not set
+# CONFIG_BSP_USING_SPI is not set
 # CONFIG_BSP_USING_PXP is not set
-CONFIG_BSP_USING_CACHE=y
+# CONFIG_BSP_USING_CACHE is not set
 
 #
 # Board extended module Drivers

bsp/imxrt/imxrt1060-nxp-evk/MIMXRT1060-EVK上手指南.md

@@ -1,57 +1,55 @@
-### MIMXRT1060-EVK上手指南
+# MIMXRT1060-EVK上手指南
 
 MIMXRT1060-EVK支持RT-Studio工程，本上手指南以RT-Studio环境的开发说明举例。
 
-#### 准备阶段
+## 1 准备阶段
 
 - 拉取rt-thread的github仓库到本地，[链接地址](https://github.com/RT-Thread/rt-thread)。
 
 - 下载安装RT-Thread Studio,[链接地址](https://www.rt-thread.org/studio.html)。
 - 准备RW007模块。
 
-#### BSP上手阶段
+## 2 BSP上手阶段
 
-- 找到MIMXRT1060-EVK BSP所在目录，使用menuconfig配置工程
+### 2.1 menuconfig配置工程
 
-  ![](./figures/6.png)
+打开MIMXRT1060-EVK BSP所在目录，在ENV工具中使用menuconfig命令配置工程
 
-  取消暂时不需要的配置，具体操作如下：
+![](./figures/6.png)
 
-  - Onboard Peripherial Drivers选项设置
+### 2.2 取消暂时不需要的配置，具体操作如下：
 
-  ![](./figures/4.png)
+Onboard Peripherial Drivers选项设置：
 
-  - On-chip Peripherial Drivers选项设置
+![](./figures/4.png)
 
-  ![](./figures/5.png)
+On-chip Peripherial Drivers选项设置：
 
-- 点击文件，选择导入选项。
+![](./figures/5.png)
+
+### 2.3 点击文件，选择导入选项。
 
 ![](./figures/1.png)
 
-- 选择导入RT-Thread Bsp 到工作空间中
+### 2.4 选择导入RT-Thread Bsp 到工作空间中
 
-  ![](./figures/2.png)
+![](./figures/2.png)
 
-  <div STYLE="page-break-after: always;"></div>
+<div STYLE="page-break-after: always;"></div>
 
-- 按照示例填写工程信息
+### 2.5 按照示例填写工程信息
 
 ![](./figures/3.png)
 
-- 移除usb文件夹包含的文件
-
-  ![](./figures/7.png)
+<div STYLE="page-break-after: always;"></div>
 
-  <div STYLE="page-break-after: always;"></div>
+### 2.6 编译工程
 
-- 编译工程
-
-  ![](./figures/8.png)
+![](./figures/8.png)
 
 工程编译通过，至此，准备阶段完成。
 
-#### 使用RT-Studio配置BSP驱动
+## 3 使用RT-Studio配置BSP驱动
 
 RT-Thread每个BSP已经默认适配了若干片上外设驱动与板载外设驱动，使用RT-Studio将相应的开关直接打开并依据使用环境配置相应参数即可使用。由于各个管脚存在复用功能，所以并不是所有的片上外设驱动与板载外设驱动都可以同时使用，使用时需要结合原理图来合理开启相应的外设驱动。
 
@@ -59,7 +57,7 @@ RT-Thread有许多软件软件包，使用RT-Studio将相应软件包的开关
 
 ![](./figures/17.png)
 
-#### 联网实操：使用RW007模块联网
+## 4 联网实操：使用RW007模块联网
 
 RW007 是由上海睿赛德电子科技有限公司开发的高速 WiFi 模块，使用 SPI 与主机通信。[RW007使用指南链接](https://www.rt-thread.org/document/site/#/rt-thread-version/rt-thread-standard/application-note/packages/rw007_module_using/an0034-rw007-module-using)。
 
@@ -67,25 +65,23 @@ MIMXRT1060-EVK板载arduino接口提供的SPI接口与SD卡的SDIO接口使用
 
 ![](./figures/11.png)
 
-##### MIMXRT1060-EVK使用RW007指南
-
-###### 1.配置板载SPI外设
+### 4.1 配置板载SPI外设
 
 RW007可采用SPI接口通讯，MIMXRT1060-EVK支持SPI驱动，默认采用轮询的方式与RW007通讯(暂不支持中断与DMA模式与RW007通讯)，使用RT-Studio配置SPI的具体配置如下:
 
 ![](./figures/10.png)
 
-###### 2.使用RT-Studio配置RW007软件包
+### 4.2 使用RT-Studio配置RW007软件包
 
 点击左侧的RT-Thread Settings选项，弹出右侧的配置菜单，在搜索栏中输入RW007,选择`rw007:SPI WIFI rw007 driver `，相应配置参数如下：
 
 ![](./figures/9.png)
 
-###### 3.将RW007模块插入板载的arduino接口
+### 4.3 将RW007模块插入板载的arduino接口
 
 ![](./figures/12.png)
 
-###### 4.修改RW007示例
+### 4.4 修改RW007示例
 
 由于RW007软件包的默认示例是基于STM32的示例，所以在RT1060-EVK上需进行少量的修改，修改RW007软件包中的example文件夹中的rw007_stm32_port.c文件。
 
@@ -112,13 +108,13 @@ int wifi_spi_device_init(void)
 }
 ```
 
-###### 5.修改完成后，编译工程，烧录固件。
+### 4.5 修改完成后，编译工程，烧录固件。
 
 ![](./figures/13.png)
 
-`rw007 sn`与`rw007 ver`可以正常输出无乱码时，RW007驱动成功！！！
+`rw007 sn`与`rw007 ver`可以正常输出无乱码时，RW007驱动成功！
 
-###### 6. wifi联网测试
+### 4.6 wifi联网测试
 
 在shell中输入`wifi scan`命令搜索WIFI。
 
@@ -132,4 +128,4 @@ int wifi_spi_device_init(void)
 
 ![](./figures/16.png)
 
-至此MIMXRT1060-EVK的基础环境便搭建测试完毕！！！。
+至此MIMXRT1060-EVK的基础环境便搭建测试完毕！

bsp/imxrt/imxrt1060-nxp-evk/rtconfig.h

@@ -45,7 +45,7 @@
 #define RT_USING_CONSOLE
 #define RT_CONSOLEBUF_SIZE 128
 #define RT_CONSOLE_DEVICE_NAME "uart1"
-#define RT_VER_NUM 0x50000
+#define RT_VER_NUM 0x50001
 #define RT_USING_CACHE
 #define RT_USING_HW_ATOMIC
 #define RT_USING_CPU_FFS
@@ -73,28 +73,9 @@
 #define MSH_USING_BUILT_IN_COMMANDS
 #define FINSH_USING_DESCRIPTION
 #define FINSH_ARG_MAX 10
-#define RT_USING_DFS
-#define DFS_USING_POSIX
-#define DFS_USING_WORKDIR
-#define DFS_FILESYSTEMS_MAX 4
-#define DFS_FILESYSTEM_TYPES_MAX 4
-#define DFS_FD_MAX 16
-#define RT_USING_DFS_ELMFAT
-
-/* elm-chan's FatFs, Generic FAT Filesystem Module */
-
-#define RT_DFS_ELM_CODE_PAGE 437
-#define RT_DFS_ELM_WORD_ACCESS
-#define RT_DFS_ELM_USE_LFN_3
-#define RT_DFS_ELM_USE_LFN 3
-#define RT_DFS_ELM_LFN_UNICODE_0
-#define RT_DFS_ELM_LFN_UNICODE 0
-#define RT_DFS_ELM_MAX_LFN 255
-#define RT_DFS_ELM_DRIVES 2
-#define RT_DFS_ELM_MAX_SECTOR_SIZE 512
-#define RT_DFS_ELM_REENTRANT
-#define RT_DFS_ELM_MUTEX_TIMEOUT 3000
-#define RT_USING_DFS_DEVFS
+
+/* DFS: device virtual file system */
+
 
 /* Device Drivers */
 
@@ -110,11 +91,6 @@
 
 /* Using USB */
 
-#define RT_USING_USB
-#define RT_USING_USB_HOST
-#define RT_USBH_MSTORAGE
-#define UDISK_MOUNTPOINT "/"
-#define RT_USBD_THREAD_STACK_SZ 4096
 
 /* C/C++ and POSIX layer */
 
@@ -131,13 +107,6 @@
 
 /* Network */
 
-#define RT_USING_NETDEV
-#define NETDEV_USING_IFCONFIG
-#define NETDEV_USING_PING
-#define NETDEV_USING_NETSTAT
-#define NETDEV_USING_AUTO_DEFAULT
-#define NETDEV_IPV4 1
-#define NETDEV_IPV6 0
 
 /* Utilities */
 
@@ -180,6 +149,9 @@
 /* u8g2: a monochrome graphic library */
 
 
+/* PainterEngine: A cross-platform graphics application framework written in C language */
+
+
 /* tools packages */
 
 
@@ -252,7 +224,6 @@
 
 /* Other */
 
-
 /* Signal IO */
 
 
@@ -267,16 +238,12 @@
 
 /* Onboard Peripheral Drivers */
 
-#define BSP_USING_SDRAM
 
 /* On-chip Peripheral Drivers */
 
 #define BSP_USING_GPIO
-#define BSP_USING_USB
-#define BSP_USB0_HOST
 #define BSP_USING_LPUART
 #define BSP_USING_LPUART1
-#define BSP_USING_CACHE
 
 /* Board extended module Drivers */