[bsp/nrf5x] fix the kconfig

bsp/nrf5x/nrf52840/board/Kconfig

@@ -12,7 +12,11 @@ config SOC_NRF52840
     config NRFX_CLOCK_DEFAULT_CONFIG_IRQ_PRIORITY
     int 
     default 7
+    config NRFX_CLOCK_CONFIG_LF_SRC
+    int 
+    default 1  
 
+    
 config SOC_NORDIC
     bool 
     config SOC_NORDIC
@@ -69,6 +73,11 @@ menu "On-chip Peripheral Drivers"
         bool "Enable GPIO"
         select RT_USING_PIN
         default y
+    if BSP_USING_GPIO
+        config NRFX_GPIOTE_ENABLED
+        int 
+        default 1  
+    endif
     config BSP_USING_SAADC
         bool "Enable SAADC"
         select RT_USING_ADC
@@ -191,10 +200,17 @@ menu "On-chip Peripheral Drivers"
         select RT_USING_SERIAL
 
         if BSP_USING_UART
+            config NRFX_UART_ENABLED
+            int 
+            default 1
+
             config BSP_USING_UART0
                 bool "Enable UART0"
                 default y 
                 if BSP_USING_UART0
+                    config NRFX_UART0_ENABLED
+                    int 
+                    default 1
                     config BSP_UART0_RX_PIN
                         int "uart0 rx pin number"
                         range 0 31
@@ -215,6 +231,9 @@ menu "On-chip Peripheral Drivers"
         default y
 
         if BSP_USING_SPI
+            config NRFX_SPI_ENABLED
+            int 
+            default 1
             config BSP_USING_SPI0
                 bool "Enable SPI0 bus"
                 default y

bsp/nrf5x/nrf52840/board/sdk_config.h

@@ -1899,7 +1899,7 @@
 // <e> NRFX_GPIOTE_ENABLED - nrfx_gpiote - GPIOTE peripheral driver
 //==========================================================
 #ifndef NRFX_GPIOTE_ENABLED
-#define NRFX_GPIOTE_ENABLED 1
+#define NRFX_GPIOTE_ENABLED 0
 #endif
 // <o> NRFX_GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS - Number of lower power input pins 
 #ifndef NRFX_GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS
@@ -2903,7 +2903,7 @@
 // <e> NRFX_QSPI_ENABLED - nrfx_qspi - QSPI peripheral driver
 //==========================================================
 #ifndef NRFX_QSPI_ENABLED
-#define NRFX_QSPI_ENABLED 1
+#define NRFX_QSPI_ENABLED 0
 #endif
 // <o> NRFX_QSPI_CONFIG_SCK_DELAY - tSHSL, tWHSL and tSHWL in number of 16 MHz periods (62.5 ns).  <0-255> 
 
@@ -4382,11 +4382,11 @@
 // <e> NRFX_UART_ENABLED - nrfx_uart - UART peripheral driver
 //==========================================================
 #ifndef NRFX_UART_ENABLED
-#define NRFX_UART_ENABLED 1
+#define NRFX_UART_ENABLED 0
 #endif
 // <o> NRFX_UART0_ENABLED - Enable UART0 instance 
 #ifndef NRFX_UART0_ENABLED
-#define NRFX_UART0_ENABLED 1
+#define NRFX_UART0_ENABLED 0
 #endif
 
 // <o> NRFX_UART_DEFAULT_CONFIG_HWFC  - Hardware Flow Control