[bsp][stm32][stm32f767-atk-apollo] Add LCD driver port

bsp/stm32/stm32f767-atk-apollo/.config

@@ -7,6 +7,7 @@
 # RT-Thread Kernel
 #
 CONFIG_RT_NAME_MAX=8
+# CONFIG_RT_USING_ARCH_DATA_TYPE is not set
 # CONFIG_RT_USING_SMP is not set
 CONFIG_RT_ALIGN_SIZE=4
 # CONFIG_RT_THREAD_PRIORITY_8 is not set
@@ -47,11 +48,11 @@ CONFIG_RT_USING_MESSAGEQUEUE=y
 # Memory Management
 #
 CONFIG_RT_USING_MEMPOOL=y
-# CONFIG_RT_USING_MEMHEAP is not set
+CONFIG_RT_USING_MEMHEAP=y
 # CONFIG_RT_USING_NOHEAP is not set
-CONFIG_RT_USING_SMALL_MEM=y
+# CONFIG_RT_USING_SMALL_MEM is not set
 # CONFIG_RT_USING_SLAB is not set
-# CONFIG_RT_USING_MEMTRACE is not set
+CONFIG_RT_USING_MEMHEAP_AS_HEAP=y
 CONFIG_RT_USING_HEAP=y
 
 #
@@ -63,8 +64,9 @@ CONFIG_RT_USING_DEVICE=y
 CONFIG_RT_USING_CONSOLE=y
 CONFIG_RT_CONSOLEBUF_SIZE=128
 CONFIG_RT_CONSOLE_DEVICE_NAME="uart1"
-CONFIG_RT_VER_NUM=0x40000
+CONFIG_RT_VER_NUM=0x40002
 CONFIG_ARCH_ARM=y
+CONFIG_RT_USING_CPU_FFS=y
 CONFIG_ARCH_ARM_CORTEX_M=y
 CONFIG_ARCH_ARM_CORTEX_M7=y
 # CONFIG_ARCH_CPU_STACK_GROWS_UPWARD is not set
@@ -111,8 +113,10 @@ CONFIG_FINSH_ARG_MAX=10
 #
 CONFIG_RT_USING_DEVICE_IPC=y
 CONFIG_RT_PIPE_BUFSZ=512
+# CONFIG_RT_USING_SYSTEM_WORKQUEUE is not set
 CONFIG_RT_USING_SERIAL=y
 CONFIG_RT_SERIAL_USING_DMA=y
+CONFIG_RT_SERIAL_RB_BUFSZ=64
 # CONFIG_RT_USING_CAN is not set
 # CONFIG_RT_USING_HWTIMER is not set
 # CONFIG_RT_USING_CPUTIME is not set
@@ -122,17 +126,17 @@ CONFIG_RT_USING_PIN=y
 # CONFIG_RT_USING_PWM is not set
 # CONFIG_RT_USING_MTD_NOR is not set
 # CONFIG_RT_USING_MTD_NAND is not set
-# CONFIG_RT_USING_MTD is not set
 # CONFIG_RT_USING_PM is not set
 # CONFIG_RT_USING_RTC is not set
 # CONFIG_RT_USING_SDIO is not set
 # CONFIG_RT_USING_SPI is not set
 # CONFIG_RT_USING_WDT is not set
 # CONFIG_RT_USING_AUDIO is not set
-
-#
-# Using WiFi
-#
+# CONFIG_RT_USING_SENSOR is not set
+# CONFIG_RT_USING_TOUCH is not set
+# CONFIG_RT_USING_HWCRYPTO is not set
+# CONFIG_RT_USING_PULSE_ENCODER is not set
+# CONFIG_RT_USING_INPUT_CAPTURE is not set
 # CONFIG_RT_USING_WIFI is not set
 
 #
@@ -146,6 +150,7 @@ CONFIG_RT_USING_PIN=y
 #
 # CONFIG_RT_USING_LIBC is not set
 # CONFIG_RT_USING_PTHREADS is not set
+CONFIG_RT_LIBC_USING_TIME=y
 
 #
 # Network
@@ -157,14 +162,14 @@ CONFIG_RT_USING_PIN=y
 # CONFIG_RT_USING_SAL is not set
 
 #
-# light weight TCP/IP stack
+# Network interface device
 #
-# CONFIG_RT_USING_LWIP is not set
+# CONFIG_RT_USING_NETDEV is not set
 
 #
-# Modbus master and slave stack
+# light weight TCP/IP stack
 #
-# CONFIG_RT_USING_MODBUS is not set
+# CONFIG_RT_USING_LWIP is not set
 
 #
 # AT commands
@@ -179,16 +184,9 @@ CONFIG_RT_USING_PIN=y
 #
 # Utilities
 #
-# CONFIG_RT_USING_LOGTRACE is not set
 # CONFIG_RT_USING_RYM is not set
 # CONFIG_RT_USING_ULOG is not set
 # CONFIG_RT_USING_UTEST is not set
-
-#
-# ARM CMSIS
-#
-# CONFIG_RT_USING_CMSIS_OS is not set
-# CONFIG_RT_USING_RTT_CMSIS is not set
 # CONFIG_RT_USING_LWP is not set
 
 #
@@ -205,6 +203,8 @@ CONFIG_RT_USING_PIN=y
 # CONFIG_PKG_USING_WEBTERMINAL is not set
 # CONFIG_PKG_USING_CJSON is not set
 # CONFIG_PKG_USING_JSMN is not set
+# CONFIG_PKG_USING_LIBMODBUS is not set
+# CONFIG_PKG_USING_FREEMODBUS is not set
 # CONFIG_PKG_USING_LJSON is not set
 # CONFIG_PKG_USING_EZXML is not set
 # CONFIG_PKG_USING_NANOPB is not set
@@ -222,10 +222,12 @@ CONFIG_RT_USING_PIN=y
 # Wiced WiFi
 #
 # CONFIG_PKG_USING_WLAN_WICED is not set
+# CONFIG_PKG_USING_RW007 is not set
 # CONFIG_PKG_USING_COAP is not set
 # CONFIG_PKG_USING_NOPOLL is not set
 # CONFIG_PKG_USING_NETUTILS is not set
 # CONFIG_PKG_USING_AT_DEVICE is not set
+# CONFIG_PKG_USING_ATSRV_SOCKET is not set
 # CONFIG_PKG_USING_WIZNET is not set
 
 #
@@ -235,7 +237,14 @@ CONFIG_RT_USING_PIN=y
 # CONFIG_PKG_USING_GAGENT_CLOUD is not set
 # CONFIG_PKG_USING_ALI_IOTKIT is not set
 # CONFIG_PKG_USING_AZURE is not set
-# CONFIG_PKG_USING_TENCENT_IOTKIT is not set
+# CONFIG_PKG_USING_TENCENT_IOTHUB is not set
+# CONFIG_PKG_USING_NIMBLE is not set
+# CONFIG_PKG_USING_OTA_DOWNLOADER is not set
+# CONFIG_PKG_USING_IPMSG is not set
+# CONFIG_PKG_USING_LSSDP is not set
+# CONFIG_PKG_USING_AIRKISS_OPEN is not set
+# CONFIG_PKG_USING_LIBRWS is not set
+# CONFIG_PKG_USING_TCPSERVER is not set
 
 #
 # security packages
@@ -256,6 +265,8 @@ CONFIG_RT_USING_PIN=y
 #
 # CONFIG_PKG_USING_OPENMV is not set
 # CONFIG_PKG_USING_MUPDF is not set
+# CONFIG_PKG_USING_STEMWIN is not set
+# CONFIG_PKG_USING_WAVPLAYER is not set
 
 #
 # tools packages
@@ -267,6 +278,7 @@ CONFIG_RT_USING_PIN=y
 # CONFIG_PKG_USING_RDB is not set
 # CONFIG_PKG_USING_QRCODE is not set
 # CONFIG_PKG_USING_ULOG_EASYFLASH is not set
+# CONFIG_PKG_USING_ADBD is not set
 
 #
 # system packages
@@ -284,21 +296,35 @@ CONFIG_RT_USING_PIN=y
 # CONFIG_PKG_USING_CMSIS is not set
 # CONFIG_PKG_USING_DFS_YAFFS is not set
 # CONFIG_PKG_USING_LITTLEFS is not set
+# CONFIG_PKG_USING_THREAD_POOL is not set
+# CONFIG_PKG_USING_ROBOTS is not set
 
 #
 # peripheral libraries and drivers
 #
+# CONFIG_PKG_USING_SENSORS_DRIVERS is not set
 # CONFIG_PKG_USING_REALTEK_AMEBA is not set
 # CONFIG_PKG_USING_SHT2X is not set
-# CONFIG_PKG_USING_AHT10 is not set
-# CONFIG_PKG_USING_AP3216C is not set
 # CONFIG_PKG_USING_STM32_SDIO is not set
 # CONFIG_PKG_USING_ICM20608 is not set
 # CONFIG_PKG_USING_U8G2 is not set
 # CONFIG_PKG_USING_BUTTON is not set
-# CONFIG_PKG_USING_MPU6XXX is not set
 # CONFIG_PKG_USING_PCF8574 is not set
+# CONFIG_PKG_USING_SX12XX is not set
+# CONFIG_PKG_USING_SIGNAL_LED is not set
+# CONFIG_PKG_USING_LEDBLINK is not set
+# CONFIG_PKG_USING_WM_LIBRARIES is not set
 # CONFIG_PKG_USING_KENDRYTE_SDK is not set
+# CONFIG_PKG_USING_INFRARED is not set
+# CONFIG_PKG_USING_ROSSERIAL is not set
+# CONFIG_PKG_USING_AT24CXX is not set
+# CONFIG_PKG_USING_MOTIONDRIVER2RTT is not set
+# CONFIG_PKG_USING_AD7746 is not set
+# CONFIG_PKG_USING_PCA9685 is not set
+# CONFIG_PKG_USING_I2C_TOOLS is not set
+# CONFIG_PKG_USING_NRF24L01 is not set
+# CONFIG_PKG_USING_TOUCH_DRIVERS is not set
+# CONFIG_PKG_USING_LCD_DRIVERS is not set
 
 #
 # miscellaneous packages
@@ -314,6 +340,7 @@ CONFIG_RT_USING_PIN=y
 # CONFIG_PKG_USING_DSTR is not set
 # CONFIG_PKG_USING_TINYFRAME is not set
 # CONFIG_PKG_USING_KENDRYTE_DEMO is not set
+# CONFIG_PKG_USING_DIGITALCTRL is not set
 
 #
 # samples: kernel and components samples
@@ -324,6 +351,8 @@ CONFIG_RT_USING_PIN=y
 # CONFIG_PKG_USING_PERIPHERAL_SAMPLES is not set
 # CONFIG_PKG_USING_HELLO is not set
 # CONFIG_PKG_USING_VI is not set
+# CONFIG_PKG_USING_NNOM is not set
+# CONFIG_PKG_USING_LIBANN is not set
 CONFIG_SOC_FAMILY_STM32=y
 CONFIG_SOC_SERIES_STM32F7=y
 
@@ -337,12 +366,13 @@ CONFIG_SOC_STM32F767IG=y
 #
 CONFIG_BSP_USING_USB_TO_USART=y
 # CONFIG_BSP_USING_RS232 is not set
-# CONFIG_BSP_USING_SDRAM is not set
+CONFIG_BSP_USING_SDRAM=y
 # CONFIG_BSP_USING_QSPI_FLASH is not set
 # CONFIG_BSP_USING_MPU9250 is not set
 # CONFIG_BSP_USING_ETH is not set
 # CONFIG_BSP_USING_POT is not set
 # CONFIG_BSP_USING_SDCARD is not set
+CONFIG_BSP_USING_LCD=y
 
 #
 # On-chip Peripheral Drivers
@@ -364,6 +394,10 @@ CONFIG_BSP_USING_UART1=y
 # CONFIG_BSP_USING_ONCHIP_RTC is not set
 # CONFIG_BSP_USING_WDT is not set
 # CONFIG_BSP_USING_SDIO is not set
+CONFIG_BSP_USING_LTDC=y
+# CONFIG_BSP_USING_CRC is not set
+# CONFIG_BSP_USING_RNG is not set
+# CONFIG_BSP_USING_UDID is not set
 
 #
 # Board extended module Drivers

bsp/stm32/stm32f767-atk-apollo/board/CubeMX_Config/CubeMX_Config.ioc

@@ -17,123 +17,144 @@ KeepUserPlacement=false
 Mcu.Family=STM32F7
 Mcu.IP0=ADC1
 Mcu.IP1=CORTEX_M7
-Mcu.IP10=SPI2
-Mcu.IP11=SYS
-Mcu.IP12=TIM2
-Mcu.IP13=TIM3
-Mcu.IP14=TIM11
-Mcu.IP15=TIM13
-Mcu.IP16=TIM14
-Mcu.IP17=USART1
-Mcu.IP18=USART2
+Mcu.IP10=SDMMC1
+Mcu.IP11=SPI2
+Mcu.IP12=SYS
+Mcu.IP13=TIM2
+Mcu.IP14=TIM3
+Mcu.IP15=TIM11
+Mcu.IP16=TIM13
+Mcu.IP17=TIM14
+Mcu.IP18=USART1
+Mcu.IP19=USART2
 Mcu.IP2=ETH
 Mcu.IP3=FMC
 Mcu.IP4=IWDG
-Mcu.IP5=NVIC
-Mcu.IP6=QUADSPI
-Mcu.IP7=RCC
-Mcu.IP8=RTC
-Mcu.IP9=SDMMC1
-Mcu.IPNb=19
+Mcu.IP5=LTDC
+Mcu.IP6=NVIC
+Mcu.IP7=QUADSPI
+Mcu.IP8=RCC
+Mcu.IP9=RTC
+Mcu.IPNb=20
 Mcu.Name=STM32F767I(G-I)Tx
 Mcu.Package=LQFP176
 Mcu.Pin0=PC14/OSC32_IN
 Mcu.Pin1=PC15/OSC32_OUT
-Mcu.Pin10=PF8
-Mcu.Pin11=PF9
-Mcu.Pin12=PH0/OSC_IN
-Mcu.Pin13=PH1/OSC_OUT
-Mcu.Pin14=PC0
-Mcu.Pin15=PC1
-Mcu.Pin16=PC2
-Mcu.Pin17=PC3
-Mcu.Pin18=PA1
-Mcu.Pin19=PA2
-Mcu.Pin2=PF0
-Mcu.Pin20=PA3
-Mcu.Pin21=PA5
-Mcu.Pin22=PA7
-Mcu.Pin23=PC4
-Mcu.Pin24=PC5
-Mcu.Pin25=PB0
-Mcu.Pin26=PB2
-Mcu.Pin27=PF11
-Mcu.Pin28=PF12
-Mcu.Pin29=PF13
-Mcu.Pin3=PF1
-Mcu.Pin30=PF14
-Mcu.Pin31=PF15
-Mcu.Pin32=PG0
-Mcu.Pin33=PG1
-Mcu.Pin34=PE7
-Mcu.Pin35=PE8
-Mcu.Pin36=PE9
-Mcu.Pin37=PE10
-Mcu.Pin38=PE11
-Mcu.Pin39=PE12
-Mcu.Pin4=PF2
-Mcu.Pin40=PE13
-Mcu.Pin41=PE14
-Mcu.Pin42=PE15
-Mcu.Pin43=PB11
-Mcu.Pin44=PB13
-Mcu.Pin45=PB14
-Mcu.Pin46=PB15
-Mcu.Pin47=PD8
-Mcu.Pin48=PD9
-Mcu.Pin49=PD10
-Mcu.Pin5=PF3
-Mcu.Pin50=PD14
-Mcu.Pin51=PD15
-Mcu.Pin52=PG2
-Mcu.Pin53=PG4
-Mcu.Pin54=PG5
-Mcu.Pin55=PG8
-Mcu.Pin56=PC8
-Mcu.Pin57=PC9
-Mcu.Pin58=PA9
-Mcu.Pin59=PA10
-Mcu.Pin6=PF4
-Mcu.Pin60=PA13
-Mcu.Pin61=PA14
-Mcu.Pin62=PC10
-Mcu.Pin63=PC11
-Mcu.Pin64=PC12
-Mcu.Pin65=PD0
-Mcu.Pin66=PD1
-Mcu.Pin67=PD2
-Mcu.Pin68=PD5
-Mcu.Pin69=PD6
-Mcu.Pin7=PF5
-Mcu.Pin70=PG13
-Mcu.Pin71=PG14
-Mcu.Pin72=PG15
-Mcu.Pin73=PB6
-Mcu.Pin74=VP_IWDG_VS_IWDG
-Mcu.Pin75=VP_RTC_VS_RTC_Activate
-Mcu.Pin76=VP_SYS_VS_Systick
-Mcu.Pin77=VP_TIM3_VS_ClockSourceINT
-Mcu.Pin78=VP_TIM11_VS_ClockSourceINT
-Mcu.Pin79=VP_TIM13_VS_ClockSourceINT
-Mcu.Pin8=PF6
-Mcu.Pin80=VP_TIM14_VS_ClockSourceINT
-Mcu.Pin9=PF7
-Mcu.PinsNb=81
+Mcu.Pin10=PF5
+Mcu.Pin100=VP_TIM14_VS_ClockSourceINT
+Mcu.Pin11=PF6
+Mcu.Pin12=PF7
+Mcu.Pin13=PF8
+Mcu.Pin14=PF9
+Mcu.Pin15=PF10
+Mcu.Pin16=PH0/OSC_IN
+Mcu.Pin17=PH1/OSC_OUT
+Mcu.Pin18=PC0
+Mcu.Pin19=PC1
+Mcu.Pin2=PI9
+Mcu.Pin20=PC2
+Mcu.Pin21=PC3
+Mcu.Pin22=PA1
+Mcu.Pin23=PA2
+Mcu.Pin24=PH4
+Mcu.Pin25=PA3
+Mcu.Pin26=PA5
+Mcu.Pin27=PA6
+Mcu.Pin28=PA7
+Mcu.Pin29=PC4
+Mcu.Pin3=PI10
+Mcu.Pin30=PC5
+Mcu.Pin31=PB0
+Mcu.Pin32=PB1
+Mcu.Pin33=PB2
+Mcu.Pin34=PF11
+Mcu.Pin35=PF12
+Mcu.Pin36=PF13
+Mcu.Pin37=PF14
+Mcu.Pin38=PF15
+Mcu.Pin39=PG0
+Mcu.Pin4=PI11
+Mcu.Pin40=PG1
+Mcu.Pin41=PE7
+Mcu.Pin42=PE8
+Mcu.Pin43=PE9
+Mcu.Pin44=PE10
+Mcu.Pin45=PE11
+Mcu.Pin46=PE12
+Mcu.Pin47=PE13
+Mcu.Pin48=PE14
+Mcu.Pin49=PE15
+Mcu.Pin5=PF0
+Mcu.Pin50=PB10
+Mcu.Pin51=PB11
+Mcu.Pin52=PH9
+Mcu.Pin53=PH10
+Mcu.Pin54=PH11
+Mcu.Pin55=PB13
+Mcu.Pin56=PB14
+Mcu.Pin57=PB15
+Mcu.Pin58=PD8
+Mcu.Pin59=PD9
+Mcu.Pin6=PF1
+Mcu.Pin60=PD10
+Mcu.Pin61=PD14
+Mcu.Pin62=PD15
+Mcu.Pin63=PG2
+Mcu.Pin64=PG4
+Mcu.Pin65=PG5
+Mcu.Pin66=PG6
+Mcu.Pin67=PG7
+Mcu.Pin68=PG8
+Mcu.Pin69=PC8
+Mcu.Pin7=PF2
+Mcu.Pin70=PC9
+Mcu.Pin71=PA8
+Mcu.Pin72=PA9
+Mcu.Pin73=PA10
+Mcu.Pin74=PA13
+Mcu.Pin75=PH14
+Mcu.Pin76=PI2
+Mcu.Pin77=PA14
+Mcu.Pin78=PC10
+Mcu.Pin79=PC11
+Mcu.Pin8=PF3
+Mcu.Pin80=PC12
+Mcu.Pin81=PD0
+Mcu.Pin82=PD1
+Mcu.Pin83=PD2
+Mcu.Pin84=PD5
+Mcu.Pin85=PD6
+Mcu.Pin86=PG12
+Mcu.Pin87=PG13
+Mcu.Pin88=PG14
+Mcu.Pin89=PG15
+Mcu.Pin9=PF4
+Mcu.Pin90=PB6
+Mcu.Pin91=PB8
+Mcu.Pin92=PB9
+Mcu.Pin93=PI5
+Mcu.Pin94=VP_IWDG_VS_IWDG
+Mcu.Pin95=VP_RTC_VS_RTC_Activate
+Mcu.Pin96=VP_SYS_VS_Systick
+Mcu.Pin97=VP_TIM3_VS_ClockSourceINT
+Mcu.Pin98=VP_TIM11_VS_ClockSourceINT
+Mcu.Pin99=VP_TIM13_VS_ClockSourceINT
+Mcu.PinsNb=101
 Mcu.ThirdPartyNb=0
 Mcu.UserConstants=
 Mcu.UserName=STM32F767IGTx
-MxCube.Version=5.0.0
-MxDb.Version=DB.5.0.0
-NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false
+MxCube.Version=5.3.0
+MxDb.Version=DB.5.0.30
+NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false\:false
 NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
-NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
+NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
+NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
 PA1.Mode=RMII
 PA1.Signal=ETH_REF_CLK
 PA10.Locked=true
@@ -147,13 +168,21 @@ PA2.Mode=RMII
 PA2.Signal=ETH_MDIO
 PA3.Signal=S_TIM2_CH4
 PA5.Signal=ADCx_IN5
+PA6.Mode=RGB565
+PA6.Signal=LTDC_G2
 PA7.Mode=RMII
 PA7.Signal=ETH_CRS_DV
+PA8.Mode=RGB565
+PA8.Signal=LTDC_B3
 PA9.Locked=true
 PA9.Mode=Asynchronous
 PA9.Signal=USART1_TX
 PB0.Locked=true
 PB0.Signal=S_TIM3_CH3
+PB1.Mode=RGB565
+PB1.Signal=LTDC_R6
+PB10.Mode=RGB565
+PB10.Signal=LTDC_G4
 PB11.Locked=true
 PB11.Mode=RMII
 PB11.Signal=ETH_TX_EN
@@ -172,6 +201,10 @@ PB2.Signal=QUADSPI_CLK
 PB6.Locked=true
 PB6.Mode=Single Bank 1
 PB6.Signal=QUADSPI_BK1_NCS
+PB8.Mode=RGB565
+PB8.Signal=LTDC_B6
+PB9.Mode=RGB565
+PB9.Signal=LTDC_B7
 PC0.Signal=FMC_SDNWE
 PC1.Mode=RMII
 PC1.Signal=ETH_MDC
@@ -229,6 +262,8 @@ PE8.Signal=FMC_D5_DA5
 PE9.Signal=FMC_D6_DA6
 PF0.Signal=FMC_A0
 PF1.Signal=FMC_A1
+PF10.Mode=RGB565
+PF10.Signal=LTDC_DE
 PF11.Signal=FMC_SDNRAS
 PF12.Signal=FMC_A6
 PF13.Signal=FMC_A7
@@ -252,6 +287,8 @@ PF9.Mode=Single Bank 1
 PF9.Signal=QUADSPI_BK1_IO1
 PG0.Signal=FMC_A10
 PG1.Signal=FMC_A11
+PG12.Mode=RGB565
+PG12.Signal=LTDC_B4
 PG13.Locked=true
 PG13.Mode=RMII
 PG13.Signal=ETH_TXD0
@@ -261,11 +298,35 @@ PG15.Signal=FMC_SDNCAS
 PG2.Signal=FMC_A12
 PG4.Signal=FMC_A14_BA0
 PG5.Signal=FMC_A15_BA1
+PG6.Mode=RGB565
+PG6.Signal=LTDC_R7
+PG7.Mode=RGB565
+PG7.Signal=LTDC_CLK
 PG8.Signal=FMC_SDCLK
 PH0/OSC_IN.Mode=HSE-External-Oscillator
 PH0/OSC_IN.Signal=RCC_OSC_IN
 PH1/OSC_OUT.Mode=HSE-External-Oscillator
 PH1/OSC_OUT.Signal=RCC_OSC_OUT
+PH10.Mode=RGB565
+PH10.Signal=LTDC_R4
+PH11.Mode=RGB565
+PH11.Signal=LTDC_R5
+PH14.Mode=RGB565
+PH14.Signal=LTDC_G3
+PH4.Mode=RGB565
+PH4.Signal=LTDC_G5
+PH9.Mode=RGB565
+PH9.Signal=LTDC_R3
+PI10.Mode=RGB565
+PI10.Signal=LTDC_HSYNC
+PI11.Mode=RGB565
+PI11.Signal=LTDC_G6
+PI2.Mode=RGB565
+PI2.Signal=LTDC_G7
+PI5.Mode=RGB565
+PI5.Signal=LTDC_B5
+PI9.Mode=RGB565
+PI9.Signal=LTDC_VSYNC
 PinOutPanel.RotationAngle=0
 ProjectManager.AskForMigrate=true
 ProjectManager.BackupPrevious=false
@@ -303,7 +364,7 @@ RCC.APB2Freq_Value=108000000
 RCC.APB2TimFreq_Value=216000000
 RCC.CECFreq_Value=32786.88524590164
 RCC.CortexFreq_Value=216000000
-RCC.DFSDMAudioFreq_Value=96000000
+RCC.DFSDMAudioFreq_Value=144000000
 RCC.DFSDMFreq_Value=108000000
 RCC.EthernetFreq_Value=216000000
 RCC.FCLKCortexFreq_Value=216000000
@@ -316,8 +377,8 @@ RCC.I2C2Freq_Value=54000000
 RCC.I2C3Freq_Value=54000000
 RCC.I2C4Freq_Value=54000000
 RCC.I2SFreq_Value=96000000
-RCC.IPParameters=AHBFreq_Value,APB1CLKDivider,APB1Freq_Value,APB1TimFreq_Value,APB2CLKDivider,APB2Freq_Value,APB2TimFreq_Value,CECFreq_Value,CortexFreq_Value,DFSDMAudioFreq_Value,DFSDMFreq_Value,EthernetFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,I2C4Freq_Value,I2SFreq_Value,LCDTFTFreq_Value,LPTIM1Freq_Value,LSI_VALUE,MCO2PinFreq_Value,PLLCLKFreq_Value,PLLI2SPCLKFreq_Value,PLLI2SQCLKFreq_Value,PLLI2SRCLKFreq_Value,PLLI2SRoutputFreq_Value,PLLM,PLLN,PLLQ,PLLQCLKFreq_Value,PLLQoutputFreq_Value,PLLRFreq_Value,PLLSAIPCLKFreq_Value,PLLSAIQCLKFreq_Value,PLLSAIRCLKFreq_Value,PLLSAIoutputFreq_Value,PLLSourceVirtual,RNGFreq_Value,RTCClockSelection,RTCFreq_Value,SAI1Freq_Value,SAI2Freq_Value,SDMMC2Freq_Value,SDMMCClockSelection,SDMMCFreq_Value,SPDIFRXFreq_Value,SYSCLKFreq_VALUE,SYSCLKSource,UART4Freq_Value,UART5Freq_Value,UART7Freq_Value,UART8Freq_Value,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,USART6Freq_Value,USBFreq_Value,VCOI2SOutputFreq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VCOSAIOutputFreq_Value
-RCC.LCDTFTFreq_Value=48000000
+RCC.IPParameters=AHBFreq_Value,APB1CLKDivider,APB1Freq_Value,APB1TimFreq_Value,APB2CLKDivider,APB2Freq_Value,APB2TimFreq_Value,CECFreq_Value,CortexFreq_Value,DFSDMAudioFreq_Value,DFSDMFreq_Value,EthernetFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,I2C4Freq_Value,I2SFreq_Value,LCDTFTFreq_Value,LPTIM1Freq_Value,LSI_VALUE,MCO2PinFreq_Value,PLLCLKFreq_Value,PLLI2SPCLKFreq_Value,PLLI2SQCLKFreq_Value,PLLI2SRCLKFreq_Value,PLLI2SRoutputFreq_Value,PLLM,PLLN,PLLQ,PLLQCLKFreq_Value,PLLQoutputFreq_Value,PLLRFreq_Value,PLLSAIN,PLLSAIPCLKFreq_Value,PLLSAIQCLKFreq_Value,PLLSAIR,PLLSAIRCLKFreq_Value,PLLSAIRDiv,PLLSAIoutputFreq_Value,PLLSourceVirtual,RNGFreq_Value,RTCClockSelection,RTCFreq_Value,SAI1Freq_Value,SAI2Freq_Value,SDMMC2Freq_Value,SDMMCClockSelection,SDMMCFreq_Value,SPDIFRXFreq_Value,SYSCLKFreq_VALUE,SYSCLKSource,UART4Freq_Value,UART5Freq_Value,UART7Freq_Value,UART8Freq_Value,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,USART6Freq_Value,USBFreq_Value,VCOI2SOutputFreq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VCOSAIOutputFreq_Value
+RCC.LCDTFTFreq_Value=9000000
 RCC.LPTIM1Freq_Value=54000000
 RCC.LSI_VALUE=32000
 RCC.MCO2PinFreq_Value=216000000
@@ -332,16 +393,19 @@ RCC.PLLQ=9
 RCC.PLLQCLKFreq_Value=48000000
 RCC.PLLQoutputFreq_Value=48000000
 RCC.PLLRFreq_Value=216000000
-RCC.PLLSAIPCLKFreq_Value=96000000
-RCC.PLLSAIQCLKFreq_Value=96000000
-RCC.PLLSAIRCLKFreq_Value=96000000
-RCC.PLLSAIoutputFreq_Value=96000000
+RCC.PLLSAIN=288
+RCC.PLLSAIPCLKFreq_Value=144000000
+RCC.PLLSAIQCLKFreq_Value=144000000
+RCC.PLLSAIR=4
+RCC.PLLSAIRCLKFreq_Value=72000000
+RCC.PLLSAIRDiv=RCC_PLLSAIDIVR_8
+RCC.PLLSAIoutputFreq_Value=144000000
 RCC.PLLSourceVirtual=RCC_PLLSOURCE_HSE
 RCC.RNGFreq_Value=48000000
 RCC.RTCClockSelection=RCC_RTCCLKSOURCE_LSE
 RCC.RTCFreq_Value=32768
-RCC.SAI1Freq_Value=96000000
-RCC.SAI2Freq_Value=96000000
+RCC.SAI1Freq_Value=144000000
+RCC.SAI2Freq_Value=144000000
 RCC.SDMMC2Freq_Value=216000000
 RCC.SDMMCClockSelection=RCC_SDMMC1CLKSOURCE_CLK48
 RCC.SDMMCFreq_Value=48000000
@@ -360,7 +424,7 @@ RCC.USBFreq_Value=48000000
 RCC.VCOI2SOutputFreq_Value=192000000
 RCC.VCOInputFreq_Value=1000000
 RCC.VCOOutputFreq_Value=432000000
-RCC.VCOSAIOutputFreq_Value=192000000
+RCC.VCOSAIOutputFreq_Value=288000000
 SH.ADCx_IN5.0=ADC1_IN5,IN5
 SH.ADCx_IN5.ConfNb=1
 SH.FMC_A0.0=FMC_A0,13b-sda1

bsp/stm32/stm32f767-atk-apollo/board/CubeMX_Config/Inc/stm32f7xx_hal_conf.h

@@ -1,33 +1,20 @@
 /**
   ******************************************************************************
-  * @file    stm32f7xx_hal_conf.h
-  * @brief   HAL configuration file.
+  * @file    stm32f7xx_hal_conf_template.h
+  * @author  MCD Application Team
+  * @brief   HAL configuration template file. 
+  *          This file should be copied to the application folder and renamed
+  *          to stm32f7xx_hal_conf.h.
   ******************************************************************************
   * @attention
   *
-  * <h2><center>&copy; COPYRIGHT(c) 2018 STMicroelectronics</center></h2>
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
   *
-  * Redistribution and use in source and binary forms, with or without modification,
-  * are permitted provided that the following conditions are met:
-  *   1. Redistributions of source code must retain the above copyright notice,
-  *      this list of conditions and the following disclaimer.
-  *   2. Redistributions in binary form must reproduce the above copyright notice,
-  *      this list of conditions and the following disclaimer in the documentation
-  *      and/or other materials provided with the distribution.
-  *   3. Neither the name of STMicroelectronics nor the names of its contributors
-  *      may be used to endorse or promote products derived from this software
-  *      without specific prior written permission.
-  *
-  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
   *
   ******************************************************************************
   */ 
@@ -49,7 +36,7 @@
   */
 #define HAL_MODULE_ENABLED  
 
-#define HAL_ADC_MODULE_ENABLED
+  #define HAL_ADC_MODULE_ENABLED
 /* #define HAL_CRYP_MODULE_ENABLED   */
 /* #define HAL_CAN_MODULE_ENABLED   */
 /* #define HAL_CEC_MODULE_ENABLED   */
@@ -67,7 +54,7 @@
 /* #define HAL_I2S_MODULE_ENABLED   */
 #define HAL_IWDG_MODULE_ENABLED
 /* #define HAL_LPTIM_MODULE_ENABLED   */
-/* #define HAL_LTDC_MODULE_ENABLED   */
+#define HAL_LTDC_MODULE_ENABLED
 #define HAL_QSPI_MODULE_ENABLED
 /* #define HAL_RNG_MODULE_ENABLED   */
 #define HAL_RTC_MODULE_ENABLED
@@ -89,9 +76,9 @@
 /* #define HAL_JPEG_MODULE_ENABLED   */
 /* #define HAL_MDIOS_MODULE_ENABLED   */
 /* #define HAL_SMBUS_MODULE_ENABLED   */
-/* #define HAL_MMC_MODULE_ENABLED   */
 /* #define HAL_EXTI_MODULE_ENABLED   */
 #define HAL_GPIO_MODULE_ENABLED
+#define HAL_EXTI_MODULE_ENABLED 
 #define HAL_DMA_MODULE_ENABLED
 #define HAL_RCC_MODULE_ENABLED
 #define HAL_FLASH_MODULE_ENABLED
@@ -221,12 +208,12 @@
 #define PHY_JABBER_DETECTION            ((uint16_t)0x0002U)  /*!< Jabber condition detected            */
   
 /* Section 4: Extended PHY Registers */
-#define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
+#define PHY_SR                          ((uint16_t)0x1FU)    /*!< PHY status register Offset                      */
 
-#define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
-#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
+#define PHY_SPEED_STATUS                ((uint16_t)0x0004U)  /*!< PHY Speed mask                                  */
+#define PHY_DUPLEX_STATUS               ((uint16_t)0x0010U)  /*!< PHY Duplex mask                                 */
 
-#define PHY_ISFR                        ((uint16_t)0x000BU)    /*!< PHY Interrupt Source Flag register Offset   */
+#define PHY_ISFR                        ((uint16_t)0x001DU)    /*!< PHY Interrupt Source Flag register Offset   */
 #define PHY_ISFR_INT4                   ((uint16_t)0x000BU)  /*!< PHY Link down inturrupt       */  
 
 /* ################## SPI peripheral configuration ########################## */

bsp/stm32/stm32f767-atk-apollo/board/CubeMX_Config/Src/main.c

@@ -68,6 +68,8 @@ ETH_HandleTypeDef heth;
 
 IWDG_HandleTypeDef hiwdg;
 
+LTDC_HandleTypeDef hltdc;
+
 QSPI_HandleTypeDef hqspi;
 
 RTC_HandleTypeDef hrtc;
@@ -109,6 +111,7 @@ static void MX_TIM11_Init(void);
 static void MX_TIM13_Init(void);
 static void MX_TIM14_Init(void);
 static void MX_TIM3_Init(void);
+static void MX_LTDC_Init(void);
 /* USER CODE BEGIN PFP */
 
 /* USER CODE END PFP */
@@ -127,6 +130,7 @@ int main(void)
   /* USER CODE BEGIN 1 */
 
   /* USER CODE END 1 */
+  
 
   /* Enable I-Cache---------------------------------------------------------*/
   SCB_EnableICache();
@@ -167,6 +171,7 @@ int main(void)
   MX_TIM13_Init();
   MX_TIM14_Init();
   MX_TIM3_Init();
+  MX_LTDC_Init();
   /* USER CODE BEGIN 2 */
 
   /* USER CODE END 2 */
@@ -192,15 +197,15 @@ void SystemClock_Config(void)
   RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
   RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};
 
-  /**Configure LSE Drive Capability 
+  /** Configure LSE Drive Capability 
   */
   HAL_PWR_EnableBkUpAccess();
   __HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_LOW);
-  /**Configure the main internal regulator output voltage 
+  /** Configure the main internal regulator output voltage 
   */
   __HAL_RCC_PWR_CLK_ENABLE();
   __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-  /**Initializes the CPU, AHB and APB busses clocks 
+  /** Initializes the CPU, AHB and APB busses clocks 
   */
   RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSI|RCC_OSCILLATORTYPE_HSE
                               |RCC_OSCILLATORTYPE_LSE;
@@ -217,13 +222,13 @@ void SystemClock_Config(void)
   {
     Error_Handler();
   }
-  /**Activate the Over-Drive mode 
+  /** Activate the Over-Drive mode 
   */
   if (HAL_PWREx_EnableOverDrive() != HAL_OK)
   {
     Error_Handler();
   }
-  /**Initializes the CPU, AHB and APB busses clocks 
+  /** Initializes the CPU, AHB and APB busses clocks 
   */
   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                               |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
@@ -236,9 +241,15 @@ void SystemClock_Config(void)
   {
     Error_Handler();
   }
-  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC|RCC_PERIPHCLK_USART1
-                              |RCC_PERIPHCLK_USART2|RCC_PERIPHCLK_SDMMC1
-                              |RCC_PERIPHCLK_CLK48;
+  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_LTDC|RCC_PERIPHCLK_RTC
+                              |RCC_PERIPHCLK_USART1|RCC_PERIPHCLK_USART2
+                              |RCC_PERIPHCLK_SDMMC1|RCC_PERIPHCLK_CLK48;
+  PeriphClkInitStruct.PLLSAI.PLLSAIN = 288;
+  PeriphClkInitStruct.PLLSAI.PLLSAIR = 4;
+  PeriphClkInitStruct.PLLSAI.PLLSAIQ = 2;
+  PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV2;
+  PeriphClkInitStruct.PLLSAIDivQ = 1;
+  PeriphClkInitStruct.PLLSAIDivR = RCC_PLLSAIDIVR_8;
   PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSE;
   PeriphClkInitStruct.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK2;
   PeriphClkInitStruct.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
@@ -267,7 +278,7 @@ static void MX_ADC1_Init(void)
   /* USER CODE BEGIN ADC1_Init 1 */
 
   /* USER CODE END ADC1_Init 1 */
-  /**Configure the global features of the ADC (Clock, Resolution, Data Alignment and number of conversion) 
+  /** Configure the global features of the ADC (Clock, Resolution, Data Alignment and number of conversion) 
   */
   hadc1.Instance = ADC1;
   hadc1.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV4;
@@ -285,7 +296,7 @@ static void MX_ADC1_Init(void)
   {
     Error_Handler();
   }
-  /**Configure for the selected ADC regular channel its corresponding rank in the sequencer and its sample time. 
+  /** Configure for the selected ADC regular channel its corresponding rank in the sequencer and its sample time. 
   */
   sConfig.Channel = ADC_CHANNEL_5;
   sConfig.Rank = ADC_REGULAR_RANK_1;
@@ -374,6 +385,88 @@ static void MX_IWDG_Init(void)
 
 }
 
+/**
+  * @brief LTDC Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_LTDC_Init(void)
+{
+
+  /* USER CODE BEGIN LTDC_Init 0 */
+
+  /* USER CODE END LTDC_Init 0 */
+
+  LTDC_LayerCfgTypeDef pLayerCfg = {0};
+  LTDC_LayerCfgTypeDef pLayerCfg1 = {0};
+
+  /* USER CODE BEGIN LTDC_Init 1 */
+
+  /* USER CODE END LTDC_Init 1 */
+  hltdc.Instance = LTDC;
+  hltdc.Init.HSPolarity = LTDC_HSPOLARITY_AL;
+  hltdc.Init.VSPolarity = LTDC_VSPOLARITY_AL;
+  hltdc.Init.DEPolarity = LTDC_DEPOLARITY_AL;
+  hltdc.Init.PCPolarity = LTDC_PCPOLARITY_IPC;
+  hltdc.Init.HorizontalSync = 7;
+  hltdc.Init.VerticalSync = 3;
+  hltdc.Init.AccumulatedHBP = 14;
+  hltdc.Init.AccumulatedVBP = 5;
+  hltdc.Init.AccumulatedActiveW = 654;
+  hltdc.Init.AccumulatedActiveH = 485;
+  hltdc.Init.TotalWidth = 660;
+  hltdc.Init.TotalHeigh = 487;
+  hltdc.Init.Backcolor.Blue = 0;
+  hltdc.Init.Backcolor.Green = 0;
+  hltdc.Init.Backcolor.Red = 0;
+  if (HAL_LTDC_Init(&hltdc) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  pLayerCfg.WindowX0 = 0;
+  pLayerCfg.WindowX1 = 0;
+  pLayerCfg.WindowY0 = 0;
+  pLayerCfg.WindowY1 = 0;
+  pLayerCfg.PixelFormat = LTDC_PIXEL_FORMAT_ARGB8888;
+  pLayerCfg.Alpha = 0;
+  pLayerCfg.Alpha0 = 0;
+  pLayerCfg.BlendingFactor1 = LTDC_BLENDING_FACTOR1_CA;
+  pLayerCfg.BlendingFactor2 = LTDC_BLENDING_FACTOR2_CA;
+  pLayerCfg.FBStartAdress = 0;
+  pLayerCfg.ImageWidth = 0;
+  pLayerCfg.ImageHeight = 0;
+  pLayerCfg.Backcolor.Blue = 0;
+  pLayerCfg.Backcolor.Green = 0;
+  pLayerCfg.Backcolor.Red = 0;
+  if (HAL_LTDC_ConfigLayer(&hltdc, &pLayerCfg, 0) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  pLayerCfg1.WindowX0 = 0;
+  pLayerCfg1.WindowX1 = 0;
+  pLayerCfg1.WindowY0 = 0;
+  pLayerCfg1.WindowY1 = 0;
+  pLayerCfg1.PixelFormat = LTDC_PIXEL_FORMAT_ARGB8888;
+  pLayerCfg1.Alpha = 0;
+  pLayerCfg1.Alpha0 = 0;
+  pLayerCfg1.BlendingFactor1 = LTDC_BLENDING_FACTOR1_CA;
+  pLayerCfg1.BlendingFactor2 = LTDC_BLENDING_FACTOR2_CA;
+  pLayerCfg1.FBStartAdress = 0;
+  pLayerCfg1.ImageWidth = 0;
+  pLayerCfg1.ImageHeight = 0;
+  pLayerCfg1.Backcolor.Blue = 0;
+  pLayerCfg1.Backcolor.Green = 0;
+  pLayerCfg1.Backcolor.Red = 0;
+  if (HAL_LTDC_ConfigLayer(&hltdc, &pLayerCfg1, 1) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN LTDC_Init 2 */
+
+  /* USER CODE END LTDC_Init 2 */
+
+}
+
 /**
   * @brief QUADSPI Initialization Function
   * @param None
@@ -424,7 +517,7 @@ static void MX_RTC_Init(void)
   /* USER CODE BEGIN RTC_Init 1 */
 
   /* USER CODE END RTC_Init 1 */
-  /**Initialize RTC Only 
+  /** Initialize RTC Only 
   */
   hrtc.Instance = RTC;
   hrtc.Init.HourFormat = RTC_HOURFORMAT_24;
@@ -793,7 +886,16 @@ static void MX_USART2_UART_Init(void)
 /* FMC initialization function */
 static void MX_FMC_Init(void)
 {
-  FMC_SDRAM_TimingTypeDef SdramTiming;
+
+  /* USER CODE BEGIN FMC_Init 0 */
+
+  /* USER CODE END FMC_Init 0 */
+
+  FMC_SDRAM_TimingTypeDef SdramTiming = {0};
+
+  /* USER CODE BEGIN FMC_Init 1 */
+
+  /* USER CODE END FMC_Init 1 */
 
   /** Perform the SDRAM1 memory initialization sequence
   */
@@ -823,6 +925,9 @@ static void MX_FMC_Init(void)
     Error_Handler( );
   }
 
+  /* USER CODE BEGIN FMC_Init 2 */
+
+  /* USER CODE END FMC_Init 2 */
 }
 
 /**
@@ -835,6 +940,7 @@ static void MX_GPIO_Init(void)
 
   /* GPIO Ports Clock Enable */
   __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOI_CLK_ENABLE();
   __HAL_RCC_GPIOF_CLK_ENABLE();
   __HAL_RCC_GPIOH_CLK_ENABLE();
   __HAL_RCC_GPIOA_CLK_ENABLE();

bsp/stm32/stm32f767-atk-apollo/board/CubeMX_Config/Src/stm32f7xx_hal_msp.c

@@ -107,7 +107,6 @@ void HAL_MspInit(void)
 */
 void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
 {
-
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   if(hadc->Instance==ADC1)
   {
@@ -139,10 +138,8 @@ void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
 * @param hadc: ADC handle pointer
 * @retval None
 */
-
 void HAL_ADC_MspDeInit(ADC_HandleTypeDef* hadc)
 {
-
   if(hadc->Instance==ADC1)
   {
   /* USER CODE BEGIN ADC1_MspDeInit 0 */
@@ -171,7 +168,6 @@ void HAL_ADC_MspDeInit(ADC_HandleTypeDef* hadc)
 */
 void HAL_ETH_MspInit(ETH_HandleTypeDef* heth)
 {
-
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   if(heth->Instance==ETH)
   {
@@ -237,10 +233,8 @@ void HAL_ETH_MspInit(ETH_HandleTypeDef* heth)
 * @param heth: ETH handle pointer
 * @retval None
 */
-
 void HAL_ETH_MspDeInit(ETH_HandleTypeDef* heth)
 {
-
   if(heth->Instance==ETH)
   {
   /* USER CODE BEGIN ETH_MspDeInit 0 */
@@ -275,6 +269,194 @@ void HAL_ETH_MspDeInit(ETH_HandleTypeDef* heth)
 
 }
 
+/**
+* @brief LTDC MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hltdc: LTDC handle pointer
+* @retval None
+*/
+void HAL_LTDC_MspInit(LTDC_HandleTypeDef* hltdc)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(hltdc->Instance==LTDC)
+  {
+  /* USER CODE BEGIN LTDC_MspInit 0 */
+
+  /* USER CODE END LTDC_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_LTDC_CLK_ENABLE();
+  
+    __HAL_RCC_GPIOI_CLK_ENABLE();
+    __HAL_RCC_GPIOF_CLK_ENABLE();
+    __HAL_RCC_GPIOH_CLK_ENABLE();
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    __HAL_RCC_GPIOB_CLK_ENABLE();
+    __HAL_RCC_GPIOG_CLK_ENABLE();
+    /**LTDC GPIO Configuration    
+    PI9     ------> LTDC_VSYNC
+    PI10     ------> LTDC_HSYNC
+    PI11     ------> LTDC_G6
+    PF10     ------> LTDC_DE
+    PH4     ------> LTDC_G5
+    PA6     ------> LTDC_G2
+    PB1     ------> LTDC_R6
+    PB10     ------> LTDC_G4
+    PH9     ------> LTDC_R3
+    PH10     ------> LTDC_R4
+    PH11     ------> LTDC_R5
+    PG6     ------> LTDC_R7
+    PG7     ------> LTDC_CLK
+    PA8     ------> LTDC_B3
+    PH14     ------> LTDC_G3
+    PI2     ------> LTDC_G7
+    PG12     ------> LTDC_B4
+    PB8     ------> LTDC_B6
+    PB9     ------> LTDC_B7
+    PI5     ------> LTDC_B5 
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_2|GPIO_PIN_5;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF14_LTDC;
+    HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_11;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF9_LTDC;
+    HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_10;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF14_LTDC;
+    HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_4;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF9_LTDC;
+    HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_6;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF14_LTDC;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_1;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF9_LTDC;
+    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_8|GPIO_PIN_9;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF14_LTDC;
+    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_14;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF14_LTDC;
+    HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_6|GPIO_PIN_7;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF14_LTDC;
+    HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_8;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF13_LTDC;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_12;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+    GPIO_InitStruct.Alternate = GPIO_AF9_LTDC;
+    HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN LTDC_MspInit 1 */
+
+  /* USER CODE END LTDC_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief LTDC MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hltdc: LTDC handle pointer
+* @retval None
+*/
+void HAL_LTDC_MspDeInit(LTDC_HandleTypeDef* hltdc)
+{
+  if(hltdc->Instance==LTDC)
+  {
+  /* USER CODE BEGIN LTDC_MspDeInit 0 */
+
+  /* USER CODE END LTDC_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_LTDC_CLK_DISABLE();
+  
+    /**LTDC GPIO Configuration    
+    PI9     ------> LTDC_VSYNC
+    PI10     ------> LTDC_HSYNC
+    PI11     ------> LTDC_G6
+    PF10     ------> LTDC_DE
+    PH4     ------> LTDC_G5
+    PA6     ------> LTDC_G2
+    PB1     ------> LTDC_R6
+    PB10     ------> LTDC_G4
+    PH9     ------> LTDC_R3
+    PH10     ------> LTDC_R4
+    PH11     ------> LTDC_R5
+    PG6     ------> LTDC_R7
+    PG7     ------> LTDC_CLK
+    PA8     ------> LTDC_B3
+    PH14     ------> LTDC_G3
+    PI2     ------> LTDC_G7
+    PG12     ------> LTDC_B4
+    PB8     ------> LTDC_B6
+    PB9     ------> LTDC_B7
+    PI5     ------> LTDC_B5 
+    */
+    HAL_GPIO_DeInit(GPIOI, GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_2 
+                          |GPIO_PIN_5);
+
+    HAL_GPIO_DeInit(GPIOF, GPIO_PIN_10);
+
+    HAL_GPIO_DeInit(GPIOH, GPIO_PIN_4|GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_11 
+                          |GPIO_PIN_14);
+
+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_6|GPIO_PIN_8);
+
+    HAL_GPIO_DeInit(GPIOB, GPIO_PIN_1|GPIO_PIN_10|GPIO_PIN_8|GPIO_PIN_9);
+
+    HAL_GPIO_DeInit(GPIOG, GPIO_PIN_6|GPIO_PIN_7|GPIO_PIN_12);
+
+  /* USER CODE BEGIN LTDC_MspDeInit 1 */
+
+  /* USER CODE END LTDC_MspDeInit 1 */
+  }
+
+}
+
 /**
 * @brief QSPI MSP Initialization
 * This function configures the hardware resources used in this example
@@ -283,7 +465,6 @@ void HAL_ETH_MspDeInit(ETH_HandleTypeDef* heth)
 */
 void HAL_QSPI_MspInit(QSPI_HandleTypeDef* hqspi)
 {
-
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   if(hqspi->Instance==QUADSPI)
   {
@@ -344,10 +525,8 @@ void HAL_QSPI_MspInit(QSPI_HandleTypeDef* hqspi)
 * @param hqspi: QSPI handle pointer
 * @retval None
 */
-
 void HAL_QSPI_MspDeInit(QSPI_HandleTypeDef* hqspi)
 {
-
   if(hqspi->Instance==QUADSPI)
   {
   /* USER CODE BEGIN QUADSPI_MspDeInit 0 */
@@ -383,7 +562,6 @@ void HAL_QSPI_MspDeInit(QSPI_HandleTypeDef* hqspi)
 */
 void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc)
 {
-
   if(hrtc->Instance==RTC)
   {
   /* USER CODE BEGIN RTC_MspInit 0 */
@@ -404,10 +582,8 @@ void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc)
 * @param hrtc: RTC handle pointer
 * @retval None
 */
-
 void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc)
 {
-
   if(hrtc->Instance==RTC)
   {
   /* USER CODE BEGIN RTC_MspDeInit 0 */
@@ -430,7 +606,6 @@ void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc)
 */
 void HAL_SD_MspInit(SD_HandleTypeDef* hsd)
 {
-
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   if(hsd->Instance==SDMMC1)
   {
@@ -478,10 +653,8 @@ void HAL_SD_MspInit(SD_HandleTypeDef* hsd)
 * @param hsd: SD handle pointer
 * @retval None
 */
-
 void HAL_SD_MspDeInit(SD_HandleTypeDef* hsd)
 {
-
   if(hsd->Instance==SDMMC1)
   {
   /* USER CODE BEGIN SDMMC1_MspDeInit 0 */
@@ -518,7 +691,6 @@ void HAL_SD_MspDeInit(SD_HandleTypeDef* hsd)
 */
 void HAL_SPI_MspInit(SPI_HandleTypeDef* hspi)
 {
-
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   if(hspi->Instance==SPI2)
   {
@@ -554,10 +726,8 @@ void HAL_SPI_MspInit(SPI_HandleTypeDef* hspi)
 * @param hspi: SPI handle pointer
 * @retval None
 */
-
 void HAL_SPI_MspDeInit(SPI_HandleTypeDef* hspi)
 {
-
   if(hspi->Instance==SPI2)
   {
   /* USER CODE BEGIN SPI2_MspDeInit 0 */
@@ -588,7 +758,6 @@ void HAL_SPI_MspDeInit(SPI_HandleTypeDef* hspi)
 */
 void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef* htim_pwm)
 {
-
   if(htim_pwm->Instance==TIM2)
   {
   /* USER CODE BEGIN TIM2_MspInit 0 */
@@ -611,7 +780,6 @@ void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef* htim_pwm)
 */
 void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
 {
-
   if(htim_base->Instance==TIM3)
   {
   /* USER CODE BEGIN TIM3_MspInit 0 */
@@ -661,7 +829,6 @@ void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
 
 void HAL_TIM_MspPostInit(TIM_HandleTypeDef* htim)
 {
-
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   if(htim->Instance==TIM2)
   {
@@ -712,10 +879,8 @@ void HAL_TIM_MspPostInit(TIM_HandleTypeDef* htim)
 * @param htim_pwm: TIM_PWM handle pointer
 * @retval None
 */
-
 void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef* htim_pwm)
 {
-
   if(htim_pwm->Instance==TIM2)
   {
   /* USER CODE BEGIN TIM2_MspDeInit 0 */
@@ -736,10 +901,8 @@ void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef* htim_pwm)
 * @param htim_base: TIM_Base handle pointer
 * @retval None
 */
-
 void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim_base)
 {
-
   if(htim_base->Instance==TIM3)
   {
   /* USER CODE BEGIN TIM3_MspDeInit 0 */
@@ -795,7 +958,6 @@ void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim_base)
 */
 void HAL_UART_MspInit(UART_HandleTypeDef* huart)
 {
-
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   if(huart->Instance==USART1)
   {
@@ -854,10 +1016,8 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
 * @param huart: UART handle pointer
 * @retval None
 */
-
 void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
 {
-
   if(huart->Instance==USART1)
   {
   /* USER CODE BEGIN USART1_MspDeInit 0 */
@@ -903,7 +1063,7 @@ static void HAL_FMC_MspInit(void){
   /* USER CODE BEGIN FMC_MspInit 0 */
 
   /* USER CODE END FMC_MspInit 0 */
-  GPIO_InitTypeDef GPIO_InitStruct;
+  GPIO_InitTypeDef GPIO_InitStruct ={0};
   if (FMC_Initialized) {
     return;
   }

bsp/stm32/stm32f767-atk-apollo/board/CubeMX_Config/Src/stm32f7xx_it.c

@@ -39,7 +39,7 @@
 /* Private includes ----------------------------------------------------------*/
 /* USER CODE BEGIN Includes */
 /* USER CODE END Includes */
-
+  
 /* Private typedef -----------------------------------------------------------*/
 /* USER CODE BEGIN TD */
 
@@ -71,6 +71,7 @@
 /* USER CODE END 0 */
 
 /* External variables --------------------------------------------------------*/
+
 /* USER CODE BEGIN EV */
 
 /* USER CODE END EV */

bsp/stm32/stm32f767-atk-apollo/board/Kconfig

@@ -61,6 +61,11 @@ menu "Onboard Peripheral Drivers"
         select RT_USING_DFS
         select RT_USING_DFS_ELMFAT
         default n
+    config BSP_USING_LCD
+        bool "Enable LCD"
+        select BSP_USING_LTDC
+        select BSP_USING_SDRAM
+        default n
 
 endmenu
 
@@ -246,6 +251,10 @@ menu "On-chip Peripheral Drivers"
         select RT_USING_SDIO
         select RT_USING_DFS
         default n
+
+    config BSP_USING_LTDC
+        bool "Enable LTDC"
+        default n
 	
  source "../libraries/HAL_Drivers/Kconfig"
     

bsp/stm32/stm32f767-atk-apollo/board/board.c

@@ -16,36 +16,38 @@ void SystemClock_Config(void)
   RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
   RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};
 
-  /**Configure LSE Drive Capability 
+  /** Configure LSE Drive Capability 
   */
   HAL_PWR_EnableBkUpAccess();
   __HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_LOW);
-  /**Configure the main internal regulator output voltage 
+  /** Configure the main internal regulator output voltage 
   */
   __HAL_RCC_PWR_CLK_ENABLE();
   __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-  /**Initializes the CPU, AHB and APB busses clocks 
+  /** Initializes the CPU, AHB and APB busses clocks 
   */
-  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE|RCC_OSCILLATORTYPE_LSE;
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSI|RCC_OSCILLATORTYPE_HSE
+                              |RCC_OSCILLATORTYPE_LSE;
   RCC_OscInitStruct.HSEState = RCC_HSE_ON;
   RCC_OscInitStruct.LSEState = RCC_LSE_ON;
+  RCC_OscInitStruct.LSIState = RCC_LSI_ON;
   RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
   RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
   RCC_OscInitStruct.PLL.PLLM = 25;
   RCC_OscInitStruct.PLL.PLLN = 432;
   RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
-  RCC_OscInitStruct.PLL.PLLQ = 2;
+  RCC_OscInitStruct.PLL.PLLQ = 9;
   if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
   {
     Error_Handler();
   }
-  /**Activate the Over-Drive mode 
+  /** Activate the Over-Drive mode 
   */
   if (HAL_PWREx_EnableOverDrive() != HAL_OK)
   {
     Error_Handler();
   }
-  /**Initializes the CPU, AHB and APB busses clocks 
+  /** Initializes the CPU, AHB and APB busses clocks 
   */
   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                               |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
@@ -58,9 +60,20 @@ void SystemClock_Config(void)
   {
     Error_Handler();
   }
-  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC|RCC_PERIPHCLK_USART1;
+  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_LTDC|RCC_PERIPHCLK_RTC
+                              |RCC_PERIPHCLK_USART1|RCC_PERIPHCLK_USART2
+                              |RCC_PERIPHCLK_SDMMC1|RCC_PERIPHCLK_CLK48;
+  PeriphClkInitStruct.PLLSAI.PLLSAIN = 288;
+  PeriphClkInitStruct.PLLSAI.PLLSAIR = 4;
+  PeriphClkInitStruct.PLLSAI.PLLSAIQ = 2;
+  PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV2;
+  PeriphClkInitStruct.PLLSAIDivQ = 1;
+  PeriphClkInitStruct.PLLSAIDivR = RCC_PLLSAIDIVR_8;
   PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSE;
   PeriphClkInitStruct.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK2;
+  PeriphClkInitStruct.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
+  PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48SOURCE_PLL;
+  PeriphClkInitStruct.Sdmmc1ClockSelection = RCC_SDMMC1CLKSOURCE_CLK48;
   if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK)
   {
     Error_Handler();

bsp/stm32/stm32f767-atk-apollo/rtconfig.h

@@ -30,7 +30,8 @@
 /* Memory Management */
 
 #define RT_USING_MEMPOOL
-#define RT_USING_SMALL_MEM
+#define RT_USING_MEMHEAP
+#define RT_USING_MEMHEAP_AS_HEAP
 #define RT_USING_HEAP
 
 /* Kernel Device Object */
@@ -39,8 +40,9 @@
 #define RT_USING_CONSOLE
 #define RT_CONSOLEBUF_SIZE 128
 #define RT_CONSOLE_DEVICE_NAME "uart1"
-#define RT_VER_NUM 0x40000
+#define RT_VER_NUM 0x40002
 #define ARCH_ARM
+#define RT_USING_CPU_FFS
 #define ARCH_ARM_CORTEX_M
 #define ARCH_ARM_CORTEX_M7
 
@@ -79,26 +81,25 @@
 #define RT_PIPE_BUFSZ 512
 #define RT_USING_SERIAL
 #define RT_SERIAL_USING_DMA
+#define RT_SERIAL_RB_BUFSZ 64
 #define RT_USING_PIN
 
-/* Using WiFi */
-
-
 /* Using USB */
 
 
 /* POSIX layer and C standard library */
 
+#define RT_LIBC_USING_TIME
 
 /* Network */
 
 /* Socket abstraction layer */
 
 
-/* light weight TCP/IP stack */
+/* Network interface device */
 
 
-/* Modbus master and slave stack */
+/* light weight TCP/IP stack */
 
 
 /* AT commands */
@@ -110,9 +111,6 @@
 /* Utilities */
 
 
-/* ARM CMSIS */
-
-
 /* RT-Thread online packages */
 
 /* IoT - internet of things */
@@ -162,12 +160,15 @@
 /* Onboard Peripheral Drivers */
 
 #define BSP_USING_USB_TO_USART
+#define BSP_USING_SDRAM
+#define BSP_USING_LCD
 
 /* On-chip Peripheral Drivers */
 
 #define BSP_USING_GPIO
 #define BSP_USING_UART
 #define BSP_USING_UART1
+#define BSP_USING_LTDC
 
 /* Board extended module Drivers */