| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176 |
- menu "Hardware Drivers Config"
- config SOC_STM32F469NI
- bool
- select SOC_SERIES_STM32F4
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_SDRAM
- bool "Enable SDRAM"
- select BSP_USING_FMC
- default n
- config BSP_USING_LCD_MIPI
- bool
- default n
-
- config BSP_USING_LCD_OTM8009A
- bool "Enable LCD OTM8009A"
- select BSP_USING_SDRAM
- select BSP_USING_LTDC
- select BSP_USING_LCD_MIPI
- default n
- config BSP_USING_LVGL
- bool "Enable LVGL for LCD"
- select BSP_USING_LCD_OTM8009A
- select BSP_USING_TOUCH
- select PKG_USING_LVGL
- default n
- config BSP_USING_QSPI_FLASH
- bool "Enable QSPI FLASH (N25Q128A qspi1)"
- select BSP_USING_QSPI
- select RT_USING_SFUD
- select RT_SFUD_USING_QSPI
- select PKG_USING_FAL
- select FAL_USING_SFUD_PORT
- default n
-
- config BSP_MOUNT_QSPI_WITH_LFS
- bool "Mount QSPI flash to / with little fs"
- depends on BSP_USING_QSPI_FLASH
- select PKG_USING_LITTLEFS
- select RT_USING_MTD_NOR
- select RT_USING_DFS
- default y
-
- config BSP_USING_SDCARD
- bool "Enable SDCARD (sdio)"
- select BSP_USING_SDIO
- select RT_USING_DFS
- select RT_USING_DFS_ELMFAT
- select RT_USING_PIN
- default n
- if BSP_USING_SDCARD
- config SDIO_MAX_FREQ
- int "sdio max freq"
- range 0 24000000
- default 24000000
- endif
-
- config BSP_USING_TOUCH
- bool "Enable TOUCH"
- select BSP_USING_I2C1
- default n
- if BSP_USING_TOUCH
- config BSP_TOUCH_INT_PIN
- int "Touch interrupt pin"
- default 149
- config BSP_I2C_NAME
- string "I2C Bus Name"
- default "i2c1"
- endif
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- select RT_USING_SERIAL
- default y
- if BSP_USING_UART
- config BSP_USING_UART3
- bool "Enable UART3"
- default y
- config BSP_UART3_RX_USING_DMA
- bool "Enable UART3 RX DMA"
- depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
- default n
- endif
-
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- default n
- if BSP_USING_I2C1
- comment "Notice: PB8 --> 24; PB9 --> 25"
- config BSP_I2C1_SCL_PIN
- int "I2C1 scl pin number"
- range 1 176
- default 24
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 176
- default 25
- endif
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- select RT_USING_SPI
- default n
- if BSP_USING_SPI
- config BSP_USING_SPI3
- bool "Enable SPI3 BUS"
- default n
- config BSP_SPI3_TX_USING_DMA
- bool "Enable SPI3 TX DMA"
- depends on BSP_USING_SPI3
- default n
-
- config BSP_SPI3_RX_USING_DMA
- bool "Enable SPI3 RX DMA"
- depends on BSP_USING_SPI3
- select BSP_SPI3_TX_USING_DMA
- default n
- endif
-
- config BSP_USING_QSPI
- bool "Enable QSPI BUS"
- select RT_USING_QSPI
- select RT_USING_SPI
- default n
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- default n
- config BSP_USING_FMC
- bool "Enable FMC"
- default n
-
- config BSP_USING_SDIO
- bool "Enable SDIO"
- select RT_USING_SDIO
- select RT_USING_DFS
- default n
- config BSP_USING_USBD
- bool "Enable OTGFS as USB device"
- select RT_USING_USB_DEVICE
- default n
- config BSP_USING_LTDC
- bool "Enable LTDC"
- default n
- source "../libraries/HAL_Drivers/Kconfig"
-
- endmenu
- menu "Board extended module Drivers"
- endmenu
-
- endmenu
|
