| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121 |
- menu "Hardware Drivers Config"
- config SOC_STM32F746NG
- bool
- select SOC_SERIES_STM32F7
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- select RT_USING_CACHE
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_USB_TO_USART
- bool "Enable USB TO USART (uart1)"
- select BSP_USING_UART
- select BSP_USING_UART1
- default y
- config BSP_USING_SDRAM
- bool "Enable SDRAM"
- default n
- config BSP_USING_QSPI_FLASH
- bool "Enable QSPI FLASH (N25Q256 qspi1)"
- select BSP_USING_QSPI
- select RT_USING_SFUD
- select RT_SFUD_USING_QSPI
- default n
- config BSP_USING_LCD
- bool "Enable LCD"
- select BSP_USING_LTDC
- select BSP_USING_SDRAM
- default n
- config PHY_USING_LAN8720A
- bool
- config BSP_USING_ETH
- bool "Enable Ethernet"
- select RT_USING_LWIP
- select PHY_USING_LAN8720A
- default n
- config BSP_USING_SDCARD
- bool "Enable SDCARD (sdio)"
- select BSP_USING_SDIO
- select RT_USING_DFS
- select RT_USING_DFS_ELMFAT
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_UART1_RX_USING_DMA
- bool "Enable UART1 RX DMA"
- depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
- default n
- endif
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- default n
- config BSP_USING_QSPI
- bool "Enable QSPI BUS"
- select RT_USING_QSPI
- select RT_USING_SPI
- default n
- config BSP_USING_WDT
- bool "Enable Watchdog Timer"
- select RT_USING_WDT
- default n
- menuconfig BSP_USING_TIM
- bool "Enable timer"
- default n
- select RT_USING_HWTIMER
- if BSP_USING_TIM
- config BSP_USING_TIM11
- bool "Enable TIM11"
- default n
- endif
- config BSP_USING_SDIO
- bool "Enable SDIO"
- select RT_USING_SDIO
- select RT_USING_DFS
- default n
-
- config BSP_USING_FMC
- bool
- default n
- config BSP_USING_LTDC
- bool
- default n
- source "../libraries/HAL_Drivers/Kconfig"
-
- endmenu
- menu "Board extended module Drivers"
- endmenu
-
- endmenu
|
