rt-thread/bsp/stm32/stm32f407-atk-explorer/board/Kconfig

menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

    config BSP_USING_USB_TO_USART
        bool "Enable USB TO USART (uart1)"
        select BSP_USING_UART
        select BSP_USING_UART1
        default y

    config BSP_USING_COM2
        bool "Enable COM2 (uart2 pin conflict with Ethernet and PWM)"
        depends on (!BSP_USING_ETH && !BSP_USING_PWM)
        select BSP_USING_UART
        select BSP_USING_UART2
        default n

    config BSP_USING_COM3
        bool "Enable COM3 (uart3)"
        select BSP_USING_UART
        select BSP_USING_UART3
        default n

    config BSP_USING_SRAM
        bool "Enable SRAM"
        select BSP_USING_EXT_FMC_IO
        select BSP_USING_FMC
        default n

    config BSP_USING_ONBOARD_LCD
        bool "Enable ATK LCD"
        select BSP_USING_SRAM
        default n
        if BSP_USING_ONBOARD_LCD
            config BSP_USING_ONBOARD_LCD_TEST
                bool "Enable lcd fill test"
                default y
        endif

    menuconfig BSP_USING_TOUCH
        bool "Use LCD TOUCH (Default Res)"
        default n
        if BSP_USING_TOUCH
            config BSP_USING_TOUCH_CAP
                bool "Use LCD TOUCH Capacitance (i2c2)"
                select BSP_USING_I2C2
                default n
                if BSP_USING_TOUCH_CAP
                    config BSP_TOUCH_INT_PIN
                        int "Touch interrupt pin, PB1"
                        default 17
                endif

            config BSP_USING_TOUCH_RES
                bool "Use LCD TOUCH Resistance (sspi1)"
                select RT_USING_TOUCH
                select RT_TOUCH_PIN_IRQ
                select BSP_USING_SOFT_SPI
                select BSP_USING_SOFT_SPI1
                select BSP_USING_ONBOARD_LCD
                default y
                if BSP_USING_TOUCH_RES
                    config BSP_XPT2046_CS_PIN
                        string "pin name for the chip select pin"
                        default "PC.13"

                    config BSP_XPT2046_IRQ_PIN
                        string "pin name for the irq pin"
                        default "PB.1"
                endif
        endif

    config BSP_USING_LVGL
        bool "Enable LVGL for LCD"
        select BSP_USING_ONBOARD_LCD
        select BSP_USING_TOUCH
        select PKG_USING_LVGL
        default n

    if BSP_USING_LVGL
        config BSP_USING_LVGL_DEMO
            bool "Enable LVGL demo"
            default y
    endif

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (W25Q128 spi1)"
        select BSP_USING_SPI
        select BSP_USING_SPI1
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_SOFT_SPI_FLASH
        bool "Enable soft SPI FLASH (W25Q128 sspi2)"
        select BSP_USING_SOFT_SPI
        select BSP_USING_SOFT_SPI2
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_EEPROM
        bool "Enable I2C EEPROM (i2c1)"
        select BSP_USING_I2C1
        default n

    config BSP_USING_ETH
        bool "Enable Ethernet"
        default n
        select RT_USING_LWIP
        select RT_LWIP_USING_HW_CHECKSUM
        select RT_USING_POSIX_FS
        select RT_USING_POSIX_SOCKET

    config PHY_USING_LAN8720A
        bool
        depends on BSP_USING_ETH
        default y

    config BSP_USING_MPU6050
        bool "Enable MPU6050 (i2c1)"
        default n
        select BSP_USING_I2C1
        select PKG_USING_MPU6XXX

    menuconfig BSP_USING_FS
        bool "Enable File System"
        select RT_USING_DFS
        select RT_USING_DFS_ROMFS
        select RT_USING_DFS_ROMFS_USER_ROOT
        default n

        if BSP_USING_FS
            config BSP_USING_SDCARD_FATFS
                bool "Enable SDCARD (FATFS)"
                select BSP_USING_SDIO
                select RT_USING_DFS_ELMFAT
                default n

            config BSP_USING_SPI_FLASH_LITTLEFS
                bool "Enable SPI-FLASH (LittleFS)"
                select RT_USING_MTD_NOR
                select BSP_USING_SPI_FLASH
                select RT_USING_FAL
                select FAL_USING_AUTO_INIT
                select FAL_PART_HAS_TABLE_CFG
                select PKG_USING_LITTLEFS
                default n
        endif

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART1_TX_USING_DMA
                bool "Enable UART1 TX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART2
                bool "Enable UART2"
                default n

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART2_TX_USING_DMA
                bool "Enable UART2 TX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default n

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART3_TX_USING_DMA
                bool "Enable UART3 TX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART4
                bool "Enable UART4"
                default n

            config BSP_UART4_RX_USING_DMA
                bool "Enable UART4 RX DMA"
                depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART4_TX_USING_DMA
                bool "Enable UART4 TX DMA"
                depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART5
                bool "Enable UART5"
                default n

            config BSP_UART5_RX_USING_DMA
                bool "Enable UART5 RX DMA"
                depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART5_TX_USING_DMA
                bool "Enable UART5 TX DMA"
                depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART6
                bool "Enable UART6"
                default n

            config BSP_UART6_RX_USING_DMA
                bool "Enable UART6 RX DMA"
                depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART6_TX_USING_DMA
                bool "Enable UART6 TX DMA"
                depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA
                default n
        endif

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM11
                bool "Enable TIM11"
                default n

            config BSP_USING_TIM13
                bool "Enable TIM13"
                default n

            config BSP_USING_TIM14
                bool "Enable TIM14"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM2
            bool "Enable timer2 output PWM"
            default n
            if BSP_USING_PWM2
                config BSP_USING_PWM2_CH4
                    bool "Enable PWM2 channel4"
                    default n
            endif
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    menuconfig BSP_USING_SOFT_SPI
        bool "Enable soft SPI BUS"
        default n
        select RT_USING_SPI
        select RT_USING_SPI_BITOPS
        select RT_USING_PIN
        if BSP_USING_SOFT_SPI
            menuconfig BSP_USING_SOFT_SPI1
                bool "Enable soft SPI1 BUS (software simulation)"
                default n
                if BSP_USING_SOFT_SPI1
                    config BSP_S_SPI1_SCK_PIN
                        int "soft spi1 sck pin number"
                        range 1 176
                        default 16
                    config BSP_S_SPI1_MISO_PIN
                        int "soft spi1 miso pin number"
                        range 1 176
                        default 18
                    config BSP_S_SPI1_MOSI_PIN
                        int "soft spi1 mosi pin number"
                        range 1 176
                        default 91
                endif

            menuconfig BSP_USING_SOFT_SPI2
                bool "Enable soft SPI2 BUS (software simulation)"
                default n
                if BSP_USING_SOFT_SPI2
                    config BSP_S_SPI2_SCK_PIN
                        int "soft spi2 sck pin number"
                        range 1 176
                        default 19
                    config BSP_S_SPI2_MISO_PIN
                        int "soft spi2 miso pin number"
                        range 1 176
                        default 20
                    config BSP_S_SPI2_MOSI_PIN
                        int "soft spi2 mosi pin number"
                        range 1 176
                        default 21
                endif
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n

            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n

            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n

            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 0 143
                default 24
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 0 143
                default 25
        endif

    menuconfig BSP_USING_I2C2
        bool "Enable LCD Touch BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C2
            config BSP_I2C2_SCL_PIN
                int "i2c2 scl pin number, PB0"
                range 0 143
                default 16
            config BSP_I2C2_SDA_PIN
                int "I2C2 sda pin number, PF11"
                range 0 143
                default 91
        endif

    menuconfig BSP_USING_DAC
        bool "Enable DAC"
        default n
        select RT_USING_DAC
        if BSP_USING_DAC
            config BSP_USING_DAC1
                bool "Enable DAC1"
                default n
        endif

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

    config SDIO_MAX_FREQ
        int "sdio max freq"
        range 0 24000000
        depends on BSP_USING_SDIO
        default 1000000

    config BSP_USING_USBD
        bool "Enable USB Device"
        select RT_USING_USB_DEVICE
        default n

    menuconfig BSP_USING_USBH
        bool "Enable USB Host"
        select RT_USING_USB_HOST
        default n
        if BSP_USING_USBH
            menuconfig RT_USBH_MSTORAGE
                bool "Enable Udisk Drivers"
                default n
                if RT_USBH_MSTORAGE
                    config UDISK_MOUNTPOINT
                    string "Udisk mount dir"
                    default "/"
                endif
        endif

    menuconfig BSP_USING_PULSE_ENCODER
        bool "Enable Pulse Encoder"
        default n
        select RT_USING_PULSE_ENCODER
        if BSP_USING_PULSE_ENCODER
            config BSP_USING_PULSE_ENCODER4
                bool "Enable Pulse Encoder4"
                default n

        endif

    config BSP_USING_EXT_FMC_IO
        bool
        default n

    config BSP_USING_FMC
        bool
        default n
 source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

    menuconfig BSP_USING_AT_ESP8266
        bool "Enable ESP8266(AT Command, COM3)"
        default n
        select BSP_USING_COM3
        select PKG_USING_AT_DEVICE
        select AT_DEVICE_USING_ESP8266
        select AT_DEVICE_ESP8266_SAMPLE
        select AT_DEVICE_ESP8266_SAMPLE_BSP_TAKEOVER

        if BSP_USING_AT_ESP8266

            config ESP8266_SAMPLE_WIFI_SSID
                string "WIFI ssid"
                default "rtthread"

            config ESP8266_SAMPLE_WIFI_PASSWORD
                string "WIFI password"
                default "12345678"

            config ESP8266_SAMPLE_CLIENT_NAME
                string "AT client device name (Must be 'uart3')"
                default "uart3"

            config ESP8266_SAMPLE_RECV_BUFF_LEN
                int "The maximum length of receive line buffer"
                default 512

            comment "May adjust RT_SERIAL_RB_BUFSZ up to 512 if using the Serial V1 device driver"

        endif

endmenu

endmenu