| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191 |
- menu "Hardware Drivers Config"
- config SOC_STM32F429IG
- bool
- select SOC_SERIES_STM32F4
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_USB_TO_USART
- bool "Enable USB TO USART (uart1)"
- select BSP_USING_UART1
- default y
- config BSP_USING_COM2
- bool "Enable COM2 (uart2 pin conflict with Ethernet and PWM)"
- select BSP_USING_UART2
- default n
- config BSP_USING_COM3
- bool "Enable COM3 (uart3 pin conflict with Ethernet)"
- select BSP_USING_UART3
- default n
- config BSP_USING_SDRAM
- bool "Enable SDRAM"
- default n
- config BSP_USING_SPI_FLASH
- bool "Enable SPI FLASH (w25q256 spi5)"
- select BSP_USING_SPI5
- select RT_USING_SFUD
- select RT_SFUD_USING_SFDP
- default n
- config BSP_USING_MPU9250
- bool "Enable MPU 9250 (i2c1)"
- select BSP_USING_I2C1
- select PKG_USING_MPU6XXX
- default n
- config PHY_USING_LAN8720A
- bool
- config BSP_USING_ETH
- bool "Enable Ethernet"
- select BSP_USING_I2C1
- select PKG_USING_PCF8574
- select RT_USING_LWIP
- select PHY_USING_LAN8720A
- default n
- config BSP_USING_SDCARD
- bool "Enable SDCARD (sdio)"
- select BSP_USING_SDIO
- select RT_USING_DFS
- select RT_USING_DFS_ELMFAT
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- config BSP_USING_UART1
- bool "Enable UART1"
- select RT_USING_SERIAL
- default y
- config BSP_USING_UART2
- bool "Enable UART2"
- select RT_USING_SERIAL
- default n
- config BSP_USING_UART3
- bool "Enable UART3"
- select RT_USING_SERIAL
- default n
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- default n
- config BSP_USING_SPI1
- bool "Enable SPI1 BUS"
- select RT_USING_SPI
- default n
- config BSP_USING_SPI2
- bool "Enable SPI2 BUS"
- select RT_USING_SPI
- default n
- config BSP_USING_SPI5
- bool "Enable SPI5 BUS"
- select RT_USING_SPI
- default n
- config BSP_SPI_USING_DMA
- bool "Enable SPI DMA support"
- default n
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- comment "Notice: PH4 --> 116; PH5 --> 117"
- config BSP_I2C1_SCL_PIN
- int "I2C1 scl pin number"
- range 1 176
- default 116
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 176
- default 117
- endif
- menuconfig BSP_USING_TIM
- bool "Enable timer"
- default n
- select RT_USING_HWTIMER
- if BSP_USING_TIM
- config BSP_USING_TIM11
- bool "Enable TIM11"
- default n
- config BSP_USING_TIM13
- bool "Enable TIM13"
- default n
- config BSP_USING_TIM14
- bool "Enable TIM14"
- default n
- endif
- menuconfig BSP_USING_PWM
- bool "Enable pwm"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM2
- bool "Enable timer2 output pwm"
- default n
- if BSP_USING_PWM2
- config BSP_USING_PWM2_CH4
- bool "Enable PWM2 channel4"
- default n
- endif
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- config BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- select RT_USING_LIBC
- default n
- config BSP_USING_WDT
- bool "Enable Watchdog Timer"
- select RT_USING_WDT
- default n
- config BSP_USING_SDIO
- bool "Enable SDIO"
- select RT_USING_SDIO
- select RT_USING_DFS
- default n
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
