| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189 |
- menu "Hardware Drivers Config"
- menu "Onboard Peripheral Drivers"
- config BSP_USING_ARDUINO
- bool "Compatible with Arduino Ecosystem (RTduino)"
- select PKG_USING_RTDUINO
- select BSP_USING_UART1
- select BSP_USING_UART2
- select BSP_USING_GPIO
- select BSP_USING_ADC
- select BSP_USING_ADC1
- select BSP_USING_PWM
- select BSP_USING_PWM1
- select BSP_USING_PWM4
- select BSP_USING_PWM4_CH4
- select BSP_USING_PWM4_CH3
- select BSP_USING_PWM4_CH2
- select BSP_USING_PWM4_CH1
- select BSP_USING_PWM1_CH3
- select BSP_USING_PWM1_CH2
- select BSP_USING_PWM1_CH1
- select BSP_USING_SPI
- select BSP_USING_SPI1
- select BSP_SPI1_TX_USING_DMA
- select BSP_SPI1_RX_USING_DMA
- select BSP_USING_I2C
- select BSP_USING_I2C1
- select RTDUINO_USING_SPI
- select RTDUINO_USING_WIRE
- imply RTDUINO_USING_SERVO
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_UART1_RX_USING_DMA
- bool "Enable UART1 RX DMA"
- depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
- default n
- config BSP_USING_UART2
- bool "Enable UART2"
- default n
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- comment "Notice: PB2 --> 18; PB10 --> 26"
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 0 48
- default 26
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 0 48
- default 18
- endif
- menuconfig BSP_USING_PWM
- bool "Enable PWM"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM1
- bool "Enable timer1 output PWM"
- default n
- if BSP_USING_PWM1
- config BSP_USING_PWM1_CH1
- bool "Enable PWM1 channel1"
- default n
- config BSP_USING_PWM1_CH2
- bool "Enable PWM1 channel2"
- default n
- config BSP_USING_PWM1_CH3
- bool "Enable PWM1 channel3"
- default n
- endif
- menuconfig BSP_USING_PWM4
- bool "Enable timer4 output PWM"
- default n
- if BSP_USING_PWM4
- config BSP_USING_PWM4_CH1
- bool "Enable PWM4 channel1"
- default n
- config BSP_USING_PWM4_CH2
- bool "Enable PWM4 channel2"
- default n
- config BSP_USING_PWM4_CH3
- bool "Enable PWM4 channel3"
- default n
- config BSP_USING_PWM4_CH4
- bool "Enable PWM4 channel4"
- default n
- endif
- endif
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI1
- bool "Enable SPI1 BUS"
- default n
- config BSP_SPI1_TX_USING_DMA
- bool "Enable SPI1 TX DMA"
- depends on BSP_USING_SPI1
- default n
- config BSP_SPI1_RX_USING_DMA
- bool "Enable SPI1 RX DMA"
- depends on BSP_USING_SPI1
- select BSP_SPI1_TX_USING_DMA
- default n
- endif
- menuconfig BSP_USING_TIM
- bool "Enable timer"
- default n
- select RT_USING_HWTIMER
- if BSP_USING_TIM
- config BSP_USING_TIM10
- bool "Enable TIM10"
- default n
- config BSP_USING_TIM11
- bool "Enable TIM11"
- default n
- endif
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- default n
- config BSP_USING_USBD
- bool "Enable USB Device"
- select RT_USING_USB_DEVICE
- default n
- source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig"
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
