| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231 |
- menu "Hardware Drivers Config"
- config SOC_STM32L475VE
- bool
- select SOC_SERIES_STM32L4
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_STLINK_TO_USART
- bool "Enable STLINK TO USART (uart1)"
- select BSP_USING_UART
- select BSP_USING_UART1
- default y
- config BSP_USING_QSPI_FLASH
- bool "Enable QSPI FLASH"
- select BSP_USING_QSPI
- select RT_USING_SFUD
- select RT_SFUD_USING_QSPI
- default n
- config BSP_USING_SDCARD
- bool "Enable SDCARD (spi1)"
- select BSP_USING_SPI
- select BSP_USING_SPI1
- select BSP_SPI_USING_DMA
- select RT_USING_SPI_MSD
- select RT_USING_DFS
- select RT_USING_DFS_ELMFAT
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_UART1_RX_USING_DMA
- bool "Enable UART1 RX DMA"
- depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
- default y
-
- config BSP_USING_UART2
- bool "Enable UART2"
- default n
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- endif
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- default n
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI1
- bool "Enable SPI1 BUS"
- default n
- config BSP_SPI1_TX_USING_DMA
- bool "Enable SPI1 TX DMA"
- depends on BSP_USING_SPI1
- default n
-
- config BSP_SPI1_RX_USING_DMA
- bool "Enable SPI1 RX DMA"
- depends on BSP_USING_SPI1
- select BSP_SPI1_TX_USING_DMA
- default n
- config BSP_USING_SPI2
- bool "Enable SPI2 BUS"
- default n
-
- config BSP_SPI2_TX_USING_DMA
- bool "Enable SPI2 TX DMA"
- depends on BSP_USING_SPI2
- default n
-
- config BSP_SPI2_RX_USING_DMA
- bool "Enable SPI2 RX DMA"
- depends on BSP_USING_SPI2
- select BSP_SPI2_TX_USING_DMA
- default n
- endif
- config BSP_USING_QSPI
- bool "Enable QSPI BUS"
- select RT_USING_QSPI
- select RT_USING_SPI
- default n
- config BSP_QSPI_USING_DMA
- bool "Enable QSPI DMA support"
- default n
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 1 176
- default 15
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 176
- default 16
- endif
- menuconfig BSP_USING_I2C2
- bool "Enable I2C2 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C2
- config BSP_I2C2_SCL_PIN
- int "i2c2 scl pin number"
- range 1 176
- default 47
- config BSP_I2C2_SDA_PIN
- int "I2C2 sda pin number"
- range 1 176
- default 48
- endif
- menuconfig BSP_USING_I2C3
- bool "Enable I2C3 BUS (software simulation)"
- default n
- select RT_USING_I2CS
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C3
- config BSP_I2C3_SCL_PIN
- int "i2c3 scl pin number"
- range 1 176
- default 92
- config BSP_I2C3_SDA_PIN
- int "I2C3 sda pin number"
- range 1 176
- default 93
- endif
- menuconfig BSP_USING_TIM
- bool "Enable timer"
- default n
- select RT_USING_HWTIMER
- if BSP_USING_TIM
- config BSP_USING_TIM15
- bool "Enable TIM15"
- default n
- config BSP_USING_TIM16
- bool "Enable TIM16"
- default n
- config BSP_USING_TIM17
- bool "Enable TIM17"
- default n
- endif
- menuconfig BSP_USING_PWM
- bool "Enable pwm"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM4
- bool "Enable timer4 output pwm"
- default n
- if BSP_USING_PWM4
- config BSP_USING_PWM4_CH2
- bool "Enable PWM4 channel2"
- default n
-
- config BSP_USING_PWM4_CH3
- bool "Enable PWM4 channel3"
- default n
- endif
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- config BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- select RT_USING_LIBC
- default n
- config BSP_USING_WDT
- bool "Enable Watchdog Timer"
- select RT_USING_WDT
- default n
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
