rt-thread/bsp/imxrt/imxrt1050-ArchMix/drivers/board.c

/*
 * File      : board.c
 * This file is part of RT-Thread RTOS
 * COPYRIGHT (C) 2009 RT-Thread Develop Team
 *
 * The license and distribution terms for this file may be
 * found in the file LICENSE in this distribution or at
 * http://www.rt-thread.org/license/LICENSE
 *
 * Change Logs:
 * Date           Author       Notes
 * 2009-01-05     Bernard      first implementation
 */
#include <stdint.h>
#include <rthw.h>
#include <rtthread.h>

#include "board.h"
#include "drv_uart.h"

#if defined(RT_USING_SDRAM) && defined(RT_USING_MEMHEAP_AS_HEAP)
static struct rt_memheap system_heap;
#endif

/* ARM PLL configuration for RUN mode */
const clock_arm_pll_config_t armPllConfig = { .loopDivider = 100U };

/* SYS PLL configuration for RUN mode */
const clock_sys_pll_config_t sysPllConfig = { .loopDivider = 1U };

/* USB1 PLL configuration for RUN mode */
const clock_usb_pll_config_t usb1PllConfig = { .loopDivider = 0U };

static void BOARD_BootClockGate(void)
{
//    /* Disable all unused peripheral clock */
//    CCM->CCGR0 = 0x00C0000FU;
//    CCM->CCGR1 = 0x30000000U;
//    CCM->CCGR2 = 0x003F0030U;
//    CCM->CCGR3 = 0xF0000330U;
//    CCM->CCGR4 = 0x0000FF3CU;
//    CCM->CCGR5 = 0xF000330FU;
//    CCM->CCGR6 = 0x00FC0300U;
}

static void BOARD_BootClockRUN(void)
{
    /* Boot ROM did initialize the XTAL, here we only sets external XTAL OSC freq */
    CLOCK_SetXtalFreq(24000000U);
    CLOCK_SetRtcXtalFreq(32768U);

    CLOCK_SetMux(kCLOCK_PeriphClk2Mux, 0x1); /* Set PERIPH_CLK2 MUX to OSC */
    CLOCK_SetMux(kCLOCK_PeriphMux, 0x1); /* Set PERIPH_CLK MUX to PERIPH_CLK2 */

    /* Setting the VDD_SOC to 1.5V. It is necessary to config AHB to 600Mhz */
    DCDC->REG3 = (DCDC->REG3 & (~DCDC_REG3_TRG_MASK)) | DCDC_REG3_TRG(0x12);

    CLOCK_InitArmPll(&armPllConfig); /* Configure ARM PLL to 1200M */
#ifndef SKIP_SYSCLK_INIT
    CLOCK_InitSysPll(&sysPllConfig); /* Configure SYS PLL to 528M */
#endif
#ifndef SKIP_USB_PLL_INIT
    CLOCK_InitUsb1Pll(&usb1PllConfig); /* Configure USB1 PLL to 480M */
#endif
    CLOCK_SetDiv(kCLOCK_ArmDiv, 0x1); /* Set ARM PODF to 0, divide by 2 */
    CLOCK_SetDiv(kCLOCK_AhbDiv, 0x0); /* Set AHB PODF to 0, divide by 1 */
    CLOCK_SetDiv(kCLOCK_IpgDiv, 0x3); /* Set IPG PODF to 3, divede by 4 */

    CLOCK_SetMux(kCLOCK_PrePeriphMux, 0x3); /* Set PRE_PERIPH_CLK to PLL1, 1200M */
    CLOCK_SetMux(kCLOCK_PeriphMux, 0x0); /* Set PERIPH_CLK MUX to PRE_PERIPH_CLK */

    /* Disable unused clock */
    BOARD_BootClockGate();

    /* Power down all unused PLL */
    CLOCK_DeinitAudioPll();
    CLOCK_DeinitVideoPll();
    CLOCK_DeinitEnetPll();
    CLOCK_DeinitUsb2Pll();

    /* iomuxc clock (iomuxc_clk_enable): 0x03u */
    CLOCK_EnableClock(kCLOCK_Iomuxc);

    /* Update core clock */
    SystemCoreClockUpdate();
}


/* MPU configuration. */
static void BOARD_ConfigMPU(void)
{
    /* Disable I cache and D cache */
    SCB_DisableICache();
    SCB_DisableDCache();

    /* Disable MPU */
    ARM_MPU_Disable();

    /* Region 0 setting */
    MPU->RBAR = ARM_MPU_RBAR(0, 0xC0000000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 2, 0, 0, 0, 0, ARM_MPU_REGION_SIZE_512MB);

    /* Region 1 setting */
    MPU->RBAR = ARM_MPU_RBAR(1, 0x80000000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 2, 0, 0, 0, 0, ARM_MPU_REGION_SIZE_1GB);

    /* Region 2 setting */
    // spi flash: normal type, cacheable, no bufferable, no shareable
    MPU->RBAR = ARM_MPU_RBAR(2, 0x60000000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 0, 0, 1, 0, 0, ARM_MPU_REGION_SIZE_512MB);

    /* Region 3 setting */
    MPU->RBAR = ARM_MPU_RBAR(3, 0x00000000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 2, 0, 0, 0, 0, ARM_MPU_REGION_SIZE_1GB);

    /* Region 4 setting */
    MPU->RBAR = ARM_MPU_RBAR(4, 0x00000000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 0, 0, 1, 1, 0, ARM_MPU_REGION_SIZE_128KB);

    /* Region 5 setting */
    MPU->RBAR = ARM_MPU_RBAR(5, 0x20000000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 0, 0, 1, 1, 0, ARM_MPU_REGION_SIZE_128KB);

    /* Region 6 setting */
    MPU->RBAR = ARM_MPU_RBAR(6, 0x20200000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 0, 0, 1, 1, 0, ARM_MPU_REGION_SIZE_256KB);

#if defined(SDRAM_MPU_INIT)
    /* Region 7 setting */
    MPU->RBAR = ARM_MPU_RBAR(7, 0x80000000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 0, 0, 1, 1, 0, ARM_MPU_REGION_SIZE_32MB);

    /* Region 8 setting */
    MPU->RBAR = ARM_MPU_RBAR(8, 0x81E00000U);
    MPU->RASR = ARM_MPU_RASR(0, ARM_MPU_AP_FULL, 1, 1, 0, 0, 0, ARM_MPU_REGION_SIZE_2MB);
#endif

    /* Enable MPU */
    ARM_MPU_Enable(MPU_CTRL_PRIVDEFENA_Msk);

    /* Enable I cache and D cache */
    SCB_EnableDCache();
    SCB_EnableICache();
}

/**
 * This is the timer interrupt service routine.
 *
 */
void SysTick_Handler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    rt_tick_increase();

    /* leave interrupt */
    rt_interrupt_leave();
}

void SystemInitHook(void)
{
    BOARD_ConfigMPU();

#if defined(RT_USING_SDRAM)
    extern int imxrt_sdram_init(void);
    imxrt_sdram_init();
#endif
}

/**
 * This function will initial rt1050 board.
 */
void rt_hw_board_init()
{
    BOARD_BootClockRUN();

    SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND);

#ifdef RT_USING_COMPONENTS_INIT
    rt_components_board_init();
#endif

#ifdef RT_USING_CONSOLE
    rt_console_set_device(RT_CONSOLE_DEVICE_NAME);
#endif

#ifdef RT_USING_HEAP

#if defined(RT_USING_SDRAM) && defined(RT_USING_MEMHEAP_AS_HEAP)
    rt_kprintf("sdram heap, begin: 0x%p, end: 0x%p\n", SDRAM_BEGIN, SDRAM_END);
    rt_system_heap_init((void *)SDRAM_BEGIN, (void *)SDRAM_END);

    rt_kprintf("sram heap, begin: 0x%p, end: 0x%p\n", HEAP_BEGIN, HEAP_END);
    rt_memheap_init(&system_heap, "sram", (void *)HEAP_BEGIN, HEAP_SIZE);
#else
    rt_kprintf("sram heap, begin: 0x%p, end: 0x%p\n", HEAP_BEGIN, HEAP_END);
    rt_system_heap_init((void *)HEAP_BEGIN, (void *)HEAP_END);
#endif

#endif
}

/*@}*/