| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155 |
- menu "Hardware Drivers Config"
- config SOC_STM32F767IG
- bool
- select SOC_SERIES_STM32F7
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_USB_TO_USART
- bool "Enable USB TO USART (uart1)"
- select BSP_USING_UART1
- default y
- config BSP_USING_RS232
- bool "Enable RS232 (uart2 pin conflict with Ethernet)"
- select BSP_USING_UART2
- default n
- config BSP_USING_SDRAM
- bool "Enable SDRAM"
- default n
- config BSP_USING_QSPI_FLASH
- bool "Enable QSPI FLASH (W25Q256 qspi)"
- select BSP_USING_QSPI
- select RT_USING_SFUD
- select RT_SFUD_USING_QSPI
- default n
- config BSP_USING_MPU9250
- bool "Enable MPU 9250 (i2c2)"
- select BSP_USING_I2C2
- select PKG_USING_MPU6XXX
- default n
- config PHY_USING_LAN8720A
- bool
-
- config BSP_USING_ETH
- bool "Enable Ethernet"
- default n
- select RT_USING_LWIP
- select PHY_USING_LAN8720A
- config BSP_USING_SDCARD
- bool "Enable SDCARD (sdio)"
- select BSP_USING_SDIO
- select RT_USING_DFS
- select RT_USING_DFS_ELMFAT
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- config BSP_USING_UART1
- bool "Enable UART1"
- select RT_USING_SERIAL
- default y
- config BSP_USING_UART2
- bool "Enable UART2"
- select RT_USING_SERIAL
- default n
- config BSP_USING_UART3
- bool "Enable UART3"
- select RT_USING_SERIAL
- default n
- config BSP_USING_SPI2
- bool "Enable SPI2 BUS"
- select RT_USING_SPI
- default n
- config BSP_SPI_USING_DMA
- bool "Enable SPI DMA support"
- default n
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- comment "Notice: PB8 --> 24; PB9 --> 25"
- config BSP_I2C1_SCL_PIN
- int "I2C1 scl pin number"
- range 1 176
- default 24
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 176
- default 25
- endif
- menuconfig BSP_USING_I2C2
- bool "Enable I2C2 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C2
- comment "Notice: PH4 --> 116; PH5 --> 117"
- config BSP_I2C2_SCL_PIN
- int "i2c2 scl pin number"
- range 1 176
- default 116
- config BSP_I2C2_SDA_PIN
- int "I2C2 sda pin number"
- range 1 176
- default 117
- endif
- config BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- select RT_USING_LIBC
- default n
- config BSP_USING_WDT
- bool "Enable Watchdog Timer"
- select RT_USING_WDT
- default n
- config BSP_USING_SDIO
- bool "Enable SDIO"
- select RT_USING_SDIO
- select RT_USING_DFS
- default n
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
