rt-thread/bsp/imx6sx/cortex-a9/board/gpmi_iomux_config.c

/*
 * Copyright (c) 2012, Freescale Semiconductor, Inc.
 * All rights reserved.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

// File: gpmi_iomux_config.c

/* ------------------------------------------------------------------------------
 * <auto-generated>
 *     This code was generated by a tool.
 *     Runtime Version:3.4.0.0
 *
 *     Changes to this file may cause incorrect behavior and will be lost if
 *     the code is regenerated.
 * </auto-generated>
 * ------------------------------------------------------------------------------
*/

#include "iomux_config.h"
#include "registers/regsiomuxc.h"

// Function to configure IOMUXC for gpmi module.
void gpmi_iomux_config(void)
{
    // Config gpmi.NAND_ALE to pad NAND_ALE(A16)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_ALE_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_ALE(0x020E026C)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [3:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_ALE
    //     ALT1 (1) - Select instance: usdhc4 signal: SD4_RESET
    //     ALT5 (5) - Select instance: gpio6 signal: GPIO6_IO08
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_ALE_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_ALE_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_ALE_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_ALE(0x020E0654)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_ALE_SRE_V(SLOW));

    // Config gpmi.NAND_CE0_B to pad NAND_CS0_B(F15)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_CS0_B_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_CS0_B(0x020E0274)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [3:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_CE0_B
    //     ALT5 (5) - Select instance: gpio6 signal: GPIO6_IO11
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_CS0_B_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_CS0_B_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_CS0_B_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B(0x020E065C)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS0_B_SRE_V(SLOW));

    // Config gpmi.NAND_CE1_B to pad NAND_CS1_B(C16)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_CS1_B_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_CS1_B(0x020E0278)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [3:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_CE1_B
    //     ALT1 (1) - Select instance: usdhc4 signal: SD4_VSELECT
    //     ALT2 (2) - Select instance: usdhc3 signal: SD3_VSELECT
    //     ALT5 (5) - Select instance: gpio6 signal: GPIO6_IO14
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_CS1_B_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_CS1_B_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_CS1_B_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B(0x020E0660)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CS1_B_SRE_V(SLOW));

    // Config gpmi.NAND_CLE to pad NAND_CLE(C15)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_CLE_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_CLE(0x020E0270)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [3:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_CLE
    //     ALT5 (5) - Select instance: gpio6 signal: GPIO6_IO07
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_CLE_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_CLE_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_CLE_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_CLE(0x020E0658)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_CLE_SRE_V(SLOW));

    // Config gpmi.NAND_DATA00 to pad NAND_DATA00(A18)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA00_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_DATA00(0x020E0284)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_DATA00
    //     ALT1 (1) - Select instance: usdhc1 signal: SD1_DATA4
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO00
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA00_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA00_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA00_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00(0x020E066C)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA00_SRE_V(SLOW));

    // Config gpmi.NAND_DATA01 to pad NAND_DATA01(C17)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA01_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_DATA01(0x020E0288)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_DATA01
    //     ALT1 (1) - Select instance: usdhc1 signal: SD1_DATA5
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO01
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA01_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA01_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA01_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01(0x020E0670)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA01_SRE_V(SLOW));

    // Config gpmi.NAND_DATA02 to pad NAND_DATA02(F16)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA02_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_DATA02(0x020E028C)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_DATA02
    //     ALT1 (1) - Select instance: usdhc1 signal: SD1_DATA6
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO02
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA02_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA02_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA02_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02(0x020E0674)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA02_SRE_V(SLOW));

    // Config gpmi.NAND_DATA03 to pad NAND_DATA03(D17)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA03_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_DATA03(0x020E0290)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_DATA03
    //     ALT1 (1) - Select instance: usdhc1 signal: SD1_DATA7
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO03
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA03_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA03_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA03_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03(0x020E0678)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA03_SRE_V(SLOW));

    // Config gpmi.NAND_DATA04 to pad NAND_DATA04(A19)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA04_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_DATA04(0x020E0294)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_DATA04
    //     ALT1 (1) - Select instance: usdhc2 signal: SD2_DATA4
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO04
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA04_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA04_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA04_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04(0x020E067C)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA04_SRE_V(SLOW));

    // Config gpmi.NAND_DATA05 to pad NAND_DATA05(B18)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA05_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_DATA05(0x020E0298)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_DATA05
    //     ALT1 (1) - Select instance: usdhc2 signal: SD2_DATA5
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO05
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA05_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA05_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA05_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05(0x020E0680)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA05_SRE_V(SLOW));

    // Config gpmi.NAND_DATA06 to pad NAND_DATA06(E17)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA06_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_DATA06(0x020E029C)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_DATA06
    //     ALT1 (1) - Select instance: usdhc2 signal: SD2_DATA6
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO06
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA06_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA06_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA06_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06(0x020E0684)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA06_SRE_V(SLOW));

    // Config gpmi.NAND_DATA07 to pad NAND_DATA07(C18)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA07_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_DATA07(0x020E02A0)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_DATA07
    //     ALT1 (1) - Select instance: usdhc2 signal: SD2_DATA7
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO07
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA07_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA07_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_DATA07_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07(0x020E0688)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_DATA07_SRE_V(SLOW));

    // Config gpmi.NAND_DQS to pad SD4_DATA0(D18)
    // HW_IOMUXC_SW_MUX_CTL_PAD_SD4_DATA0_WR(0x00000002);
    // HW_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_SD4_DATA0(0x020E0340)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT1 (1) - Select instance: usdhc4 signal: SD4_DATA0
    //     ALT2 (2) - Select instance: gpmi signal: NAND_DQS
    //     ALT5 (5) - Select instance: gpio2 signal: GPIO2_IO08
    HW_IOMUXC_SW_MUX_CTL_PAD_SD4_DATA0_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_SD4_DATA0_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_SD4_DATA0_MUX_MODE_V(ALT2));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0(0x020E0728)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_DATA0_SRE_V(SLOW));

    // Config gpmi.NAND_READY to pad NAND_READY(B16)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_READY_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_READY(0x020E02A4)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [3:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_READY
    //     ALT5 (5) - Select instance: gpio6 signal: GPIO6_IO10
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_READY_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_READY_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_READY_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_READY(0x020E068C)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_READY_SRE_V(SLOW));

    // Config gpmi.NAND_RE_B to pad SD4_CMD(B17)
    // HW_IOMUXC_SW_MUX_CTL_PAD_SD4_CMD_WR(0x00000001);
    // HW_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_SD4_CMD(0x020E033C)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: usdhc4 signal: SD4_CMD
    //     ALT1 (1) - Select instance: gpmi signal: NAND_RE_B
    //     ALT2 (2) - Select instance: uart3 signal: UART3_TX_DATA
    //     ALT5 (5) - Select instance: gpio7 signal: GPIO7_IO09
    HW_IOMUXC_SW_MUX_CTL_PAD_SD4_CMD_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_SD4_CMD_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_SD4_CMD_MUX_MODE_V(ALT1));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_SD4_CMD(0x020E0724)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CMD_SRE_V(SLOW));

    // Config gpmi.NAND_WE_B to pad SD4_CLK(E16)
    // HW_IOMUXC_SW_MUX_CTL_PAD_SD4_CLK_WR(0x00000001);
    // HW_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_SD4_CLK(0x020E0338)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [2:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: usdhc4 signal: SD4_CLK
    //     ALT1 (1) - Select instance: gpmi signal: NAND_WE_B
    //     ALT2 (2) - Select instance: uart3 signal: UART3_RX_DATA
    //     ALT5 (5) - Select instance: gpio7 signal: GPIO7_IO10
    HW_IOMUXC_SW_MUX_CTL_PAD_SD4_CLK_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_SD4_CLK_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_SD4_CLK_MUX_MODE_V(ALT1));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_SD4_CLK(0x020E0720)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_SD4_CLK_SRE_V(SLOW));

    // Config gpmi.NAND_WP_B to pad NAND_WP_B(E15)
    // HW_IOMUXC_SW_MUX_CTL_PAD_NAND_WP_B_WR(0x00000000);
    // HW_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_WR(0x0001B0B0);
    // Mux Register:
    // IOMUXC_SW_MUX_CTL_PAD_NAND_WP_B(0x020E02A8)
    //   SION [4] - Software Input On Field Reset: DISABLED
    //              Force the selected mux mode Input path no matter of MUX_MODE functionality.
    //     DISABLED (0) - Input Path is determined by functionality of the selected mux mode (regular).
    //     ENABLED (1) - Force input path of pad.
    //   MUX_MODE [3:0] - MUX Mode Select Field Reset: ALT5
    //                    Select iomux modes to be used for pad.
    //     ALT0 (0) - Select instance: gpmi signal: NAND_WP_B
    //     ALT5 (5) - Select instance: gpio6 signal: GPIO6_IO09
    //     ALT9 (9) - Select instance: i2c4 signal: I2C4_SCL
    HW_IOMUXC_SW_MUX_CTL_PAD_NAND_WP_B_WR(
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_WP_B_SION_V(DISABLED) | 
            BF_IOMUXC_SW_MUX_CTL_PAD_NAND_WP_B_MUX_MODE_V(ALT0));
    // Pad Control Register:
    // IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B(0x020E0690)
    //   HYS [16] - Hysteresis Enable Field Reset: ENABLED
    //     DISABLED (0) - CMOS input
    //     ENABLED (1) - Schmitt trigger input
    //   PUS [15:14] - Pull Up / Down Config. Field Reset: 100K_OHM_PU
    //     100K_OHM_PD (0) - 100K Ohm Pull Down
    //     47K_OHM_PU (1) - 47K Ohm Pull Up
    //     100K_OHM_PU (2) - 100K Ohm Pull Up
    //     22K_OHM_PU (3) - 22K Ohm Pull Up
    //   PUE [13] - Pull / Keep Select Field Reset: PULL
    //     KEEP (0) - Keeper Enabled
    //     PULL (1) - Pull Enabled
    //   PKE [12] - Pull / Keep Enable Field Reset: ENABLED
    //     DISABLED (0) - Pull/Keeper Disabled
    //     ENABLED (1) - Pull/Keeper Enabled
    //   ODE [11] - Open Drain Enable Field Reset: DISABLED
    //              Enables open drain of the pin.
    //     DISABLED (0) - Output is CMOS.
    //     ENABLED (1) - Output is Open Drain.
    //   SPEED [7:6] - Speed Field Reset: 100MHZ
    //     RESERVED0 (0) - Reserved
    //     50MHZ (1) - Low (50 MHz)
    //     100MHZ (2) - Medium (100 MHz)
    //     200MHZ (3) - Maximum (200 MHz)
    //   DSE [5:3] - Drive Strength Field Reset: 40_OHM
    //     HIZ (0) - HI-Z
    //     240_OHM (1) - 240 Ohm
    //     120_OHM (2) - 120 Ohm
    //     80_OHM (3) - 80 Ohm
    //     60_OHM (4) - 60 Ohm
    //     48_OHM (5) - 48 Ohm
    //     40_OHM (6) - 40 Ohm
    //     34_OHM (7) - 34 Ohm
    //   SRE [0] - Slew Rate Field Reset: SLOW
    //             Slew rate control.
    //     SLOW (0) - Slow Slew Rate
    //     FAST (1) - Fast Slew Rate
    HW_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_WR(
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_HYS_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_PUS_V(100K_OHM_PU) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_PUE_V(PULL) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_PKE_V(ENABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_ODE_V(DISABLED) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_SPEED_V(100MHZ) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_DSE_V(40_OHM) | 
            BF_IOMUXC_SW_PAD_CTL_PAD_NAND_WP_B_SRE_V(SLOW));
}