rt-thread/bsp/nuvoton/libraries/nuc980/Driver/Include/emac_reg.h

/**************************************************************************//**
 * @file     emac_reg.h
 * @version  V1.00
 * @brief    EMAC register definition header file
 *
 * SPDX-License-Identifier: Apache-2.0
 * @copyright (C) 2017-2020 Nuvoton Technology Corp. All rights reserved.
 *****************************************************************************/
#ifndef __EMAC_REG_H__
#define __EMAC_REG_H__

#if defined ( __CC_ARM   )
    #pragma anon_unions
#endif

/**
   @addtogroup REGISTER Control Register
   @{
*/

/**
    @addtogroup EMAC Ethernet MAC Controller(EMAC)
    Memory Mapped Structure for EMAC Controller
@{ */

typedef struct
{

    /**
     * @var EMAC_T::CAMCTL
     * Offset: 0x00  CAM Comparison Control Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[0]     |AUP       |Accept Unicast Packet
     * |        |          |The AUP controls the unicast packet reception
     * |        |          |If AUP is enabled, EMAC receives all incoming packet its destination MAC address is a unicast address.
     * |        |          |0 = EMAC receives packet depends on the CAM comparison result.
     * |        |          |1 = EMAC receives all unicast packets.
     * |[1]     |AMP       |Accept Multicast Packet
     * |        |          |The AMP controls the multicast packet reception
     * |        |          |If AMP is enabled, EMAC receives all incoming packet its destination MAC address is a multicast address.
     * |        |          |0 = EMAC receives packet depends on the CAM comparison result.
     * |        |          |1 = EMAC receives all multicast packets.
     * |[2]     |ABP       |Accept Broadcast Packet
     * |        |          |The ABP controls the broadcast packet reception
     * |        |          |If ABP is enabled, EMAC receives all incoming packet its destination MAC address is a broadcast address.
     * |        |          |0 = EMAC receives packet depends on the CAM comparison result.
     * |        |          |1 = EMAC receives all broadcast packets.
     * |[3]     |COMPEN    |Complement CAM Comparison Enable Bit
     * |        |          |The COMPEN controls the complement of the CAM comparison result
     * |        |          |If the CMPEN and COMPEN are both enabled, the incoming packet with specific destination MAC address
     * |        |          |configured in CAM entry will be dropped
     * |        |          |And the incoming packet with destination MAC address does not configured in any CAM entry will be received.
     * |        |          |0 = Complement CAM comparison result Disabled.
     * |        |          |1 = Complement CAM comparison result Enabled.
     * |[4]     |CMPEN     |CAM Compare Enable Bit
     * |        |          |The CMPEN controls the enable of CAM comparison function for destination MAC address recognition
     * |        |          |If software wants to receive a packet with specific destination MAC address, configures the MAC address
     * |        |          |into CAM 12~0, then enables that CAM entry and set CMPEN to 1.
     * |        |          |0 = CAM comparison function for destination MAC address recognition Disabled.
     * |        |          |1 = CAM comparison function for destination MAC address recognition Enabled.
     * @var EMAC_T::CAMEN
     * Offset: 0x04  CAM Enable Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[0]     |CAMxEN    |CAM Entry X Enable Bit
     * |        |          |The CAMxEN controls the validation of CAM entry x.
     * |        |          |The CAM entry 13, 14 and 15 are for PAUSE control frame transmission
     * |        |          |If software wants to transmit a PAUSE control frame out to network, the enable bits of these three CAM
     * |        |          |entries all must be enabled first.
     * |        |          |0 = CAM entry x Disabled.
     * |        |          |1 = CAM entry x Enabled.
     * @var EMAC_T::CAM0M
     * Offset: 0x08  CAM0 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM0L
     * Offset: 0x0C  CAM0 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM1M
     * Offset: 0x10  CAM1 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM1L
     * Offset: 0x14  CAM1 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM2M
     * Offset: 0x18  CAM2 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM2L
     * Offset: 0x1C  CAM2 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM3M
     * Offset: 0x20  CAM3 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM3L
     * Offset: 0x24  CAM3 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM4M
     * Offset: 0x28  CAM4 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM4L
     * Offset: 0x2C  CAM4 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM5M
     * Offset: 0x30  CAM5 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM5L
     * Offset: 0x34  CAM5 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM6M
     * Offset: 0x38  CAM6 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM6L
     * Offset: 0x3C  CAM6 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM7M
     * Offset: 0x40  CAM7 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM7L
     * Offset: 0x44  CAM7 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM8M
     * Offset: 0x48  CAM8 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM8L
     * Offset: 0x4C  CAM8 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM9M
     * Offset: 0x50  CAM9 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM9L
     * Offset: 0x54  CAM9 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM10M
     * Offset: 0x58  CAM10 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM10L
     * Offset: 0x5C  CAM10 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM11M
     * Offset: 0x60  CAM11 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM11L
     * Offset: 0x64  CAM11 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM12M
     * Offset: 0x68  CAM12 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM12L
     * Offset: 0x6C  CAM12 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM13M
     * Offset: 0x70  CAM13 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM13L
     * Offset: 0x74  CAM13 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM14M
     * Offset: 0x78  CAM14 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |MACADDR2  |MAC Address Byte 2
     * |[15:8]  |MACADDR3  |MAC Address Byte 3
     * |[23:16] |MACADDR4  |MAC Address Byte 4
     * |[31:24] |MACADDR5  |MAC Address Byte 5
     * |        |          |The CAMxM keeps the bit 47~16 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM14L
     * Offset: 0x7C  CAM14 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[23:16] |MACADDR0  |MAC Address Byte 0
     * |[31:24] |MACADDR1  |MAC Address Byte 1
     * |        |          |The CAMxL keeps the bit 15~0 of MAC address
     * |        |          |The x can be the 0~14
     * |        |          |The register pair {EMAC_CAMxM, EMAC_CAMxL} represents a CAM entry and keeps a MAC address.
     * |        |          |For example, if the MAC address 00-50-BA-33-BA-44 kept in CAM entry 1, the register EMAC_CAM1M is
     * |        |          |0x0050_BA33 and EMAC_CAM1L is 0xBA44_0000.
     * @var EMAC_T::CAM15MSB
     * Offset: 0x80  CAM15 Most Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[15:0]  |OPCODE    |OP Code Field of PAUSE Control Frame
     * |        |          |In the PAUSE control frame, an op code field defined and is 0x0001.
     * |[31:16] |LENGTH    |LENGTH Field of PAUSE Control Frame
     * |        |          |In the PAUSE control frame, a LENGTH field defined and is 0x8808.
     * @var EMAC_T::CAM15LSB
     * Offset: 0x84  CAM15 Least Significant Word Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:24] |OPERAND   |Pause Parameter
     * |        |          |In the PAUSE control frame, an OPERAND field defined and controls how much time the destination
     * |        |          |Ethernet MAC Controller paused
     * |        |          |The unit of the OPERAND is a slot time, the 512-bit time.
     * @var EMAC_T::TXDSA
     * Offset: 0x88  Transmit Descriptor Link List Start Address Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |TXDSA     |Transmit Descriptor Link-list Start Address
     * |        |          |The TXDSA keeps the start address of transmit descriptor link-list
     * |        |          |If the software enables the bit TXON (EMAC_CTL[8]), the content of TXDSA will be loaded into the
     * |        |          |current transmit descriptor start address register (EMAC_CTXDSA)
     * |        |          |The TXDSA does not be updated by EMAC
     * |        |          |During the operation, EMAC will ignore the bits [1:0] of TXDSA
     * |        |          |This means that TX descriptors must locate at word boundary memory address.
     * @var EMAC_T::RXDSA
     * Offset: 0x8C  Receive Descriptor Link List Start Address Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |RXDSA     |Receive Descriptor Link-list Start Address
     * |        |          |The RXDSA keeps the start address of receive descriptor link-list
     * |        |          |If the S/W enables the bit RXON (EMAC_CTL[0]), the content of RXDSA will be loaded into the current
     * |        |          |receive descriptor start address register (EMAC_CRXDSA)
     * |        |          |The RXDSA does not be updated by EMAC
     * |        |          |During the operation, EMAC will ignore the bits [1:0] of RXDSA
     * |        |          |This means that RX descriptors must locate at word boundary memory address.
     * @var EMAC_T::CTL
     * Offset: 0x90  MAC Control Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[0]     |RXON      |Frame Reception ON
     * |        |          |The RXON controls the normal packet reception of EMAC
     * |        |          |If the RXON is set to high, the EMAC starts the packet reception process, including the RX
     * |        |          |descriptor fetching, packet reception and RX descriptor modification.
     * |        |          |It is necessary to finish EMAC initial sequence before enable RXON
     * |        |          |Otherwise, the EMAC operation is undefined.
     * |        |          |If the RXON is disabled during EMAC is receiving an incoming packet, the EMAC stops the packet
     * |        |          |reception process after the current packet reception finished.
     * |        |          |0 = Packet reception process stopped.
     * |        |          |1 = Packet reception process started.
     * |[1]     |ALP       |Accept Long Packet
     * |        |          |The ALP controls the long packet, which packet length is greater than 1518 bytes, reception
     * |        |          |If the ALP is set to high, the EMAC will accept the long packet.
     * |        |          |Otherwise, the long packet will be dropped.
     * |        |          |0 = Ethernet MAC controller dropped the long packet.
     * |        |          |1 = Ethernet MAC controller received the long packet.
     * |[2]     |ARP       |Accept Runt Packet
     * |        |          |The ARP controls the runt packet, which length is less than 64 bytes, reception
     * |        |          |If the ARP is set to high, the EMAC will accept the runt packet.
     * |        |          |Otherwise, the runt packet will be dropped.
     * |        |          |0 = Ethernet MAC controller dropped the runt packet.
     * |        |          |1 = Ethernet MAC controller received the runt packet.
     * |[3]     |ACP       |Accept Control Packet
     * |        |          |The ACP controls the control frame reception
     * |        |          |If the ACP is set to high, the EMAC will accept the control frame
     * |        |          |Otherwise, the control frame will be dropped
     * |        |          |It is recommended that S/W only enable ACP while EMAC is operating on full duplex mode.
     * |        |          |0 = Ethernet MAC controller dropped the control frame.
     * |        |          |1 = Ethernet MAC controller received the control frame.
     * |[4]     |AEP       |Accept CRC Error Packet
     * |        |          |The AEP controls the EMAC accepts or drops the CRC error packet
     * |        |          |If the AEP is set to high, the incoming packet with CRC error will be received by EMAC as a good packet.
     * |        |          |0 = Ethernet MAC controller dropped the CRC error packet.
     * |        |          |1 = Ethernet MAC controller received the CRC error packet.
     * |[5]     |STRIPCRC  |Strip CRC Checksum
     * |        |          |The STRIPCRC controls if the length of incoming packet is calculated with 4 bytes CRC checksum
     * |        |          |If the STRIPCRC is set to high, 4 bytes CRC checksum is excluded from length calculation of incoming packet.
     * |        |          |0 = The 4 bytes CRC checksum is included in packet length calculation.
     * |        |          |1 = The 4 bytes CRC checksum is excluded in packet length calculation.
     * |[6]     |WOLEN     |Wake on LAN Enable Bit
     * |        |          |The WOLEN high enables the functionality that Ethernet MAC controller checked if the incoming packet
     * |        |          |is Magic Packet and wakeup system from Power-down mode.
     * |        |          |If incoming packet was a Magic Packet and the system was in Power-down, the Ethernet MAC controller
     * |        |          |would generate a wakeup event to wake system up from Power-down mode.
     * |        |          |0 = Wake-up by Magic Packet function Disabled.
     * |        |          |1 = Wake-up by Magic Packet function Enabled.
     * |[8]     |TXON      |Frame Transmission ON
     * |        |          |The TXON controls the normal packet transmission of EMAC
     * |        |          |If the TXON is set to high, the EMAC starts the packet transmission process, including the TX
     * |        |          |descriptor fetching, packet transmission and TX descriptor modification.
     * |        |          |It is must to finish EMAC initial sequence before enable TXON
     * |        |          |Otherwise, the EMAC operation is undefined.
     * |        |          |If the TXON is disabled during EMAC is transmitting a packet out, the EMAC stops the packet
     * |        |          |transmission process after the current packet transmission finished.
     * |        |          |0 = Packet transmission process stopped.
     * |        |          |1 = Packet transmission process started.
     * |[9]     |NODEF     |No Deferral
     * |        |          |The NODEF controls the enable of deferral exceed counter
     * |        |          |If NODEF is set to high, the deferral exceed counter is disabled
     * |        |          |The NODEF is only useful while EMAC is operating on half duplex mode.
     * |        |          |0 = The deferral exceed counter Enabled.
     * |        |          |1 = The deferral exceed counter Disabled.
     * |[16]    |SDPZ      |Send PAUSE Frame
     * |        |          |The SDPZ controls the PAUSE control frame transmission.
     * |        |          |If S/W wants to send a PAUSE control frame out, the CAM entry 13, 14 and 15 must be configured
     * |        |          |first and the corresponding CAM enable bit of CAMEN register also must be set.
     * |        |          |Then, set SDPZ to 1 enables the PAUSE control frame transmission.
     * |        |          |The SDPZ is a self-clear bit
     * |        |          |This means after the PAUSE control frame transmission has completed, the SDPZ will be cleared automatically.
     * |        |          |It is recommended that only enabling SNDPAUSE while EMAC is operating in Full Duplex mode.
     * |        |          |0 = PAUSE control frame transmission completed.
     * |        |          |1 = PAUSE control frame transmission Enabled.
     * |[17]    |SQECHKEN  |SQE Checking Enable Bit
     * |        |          |The SQECHKEN controls the enable of SQE checking
     * |        |          |The SQE checking is only available while EMAC is operating on 10M bps and half duplex mode
     * |        |          |In other words, the SQECHKEN cannot affect EMAC operation, if the EMAC is operating on 100Mbps
     * |        |          |or full duplex mode.
     * |        |          |0 = SQE checking Disabled while EMAC is operating in 10Mbps and Half Duplex mode.
     * |        |          |1 = SQE checking Enabled while EMAC is operating in 10Mbps and Half Duplex mode.
     * |[18]    |FUDUP     |Full Duplex Mode Selection
     * |        |          |The FUDUP controls that if EMAC is operating on full or half duplex mode.
     * |        |          |0 = EMAC operates in half duplex mode.
     * |        |          |1 = EMAC operates in full duplex mode.
     * |[19]    |RMIIRXCTL |RMII RX Control
     * |        |          |The RMIIRXCTL control the receive data sample in RMII mode
     * |        |          |It's necessary to set this bit high when RMIIEN (EMAC_CTL[ [22]) is high.
     * |        |          |0 = RMII RX control disabled.
     * |        |          |1 = RMII RX control enabled.
     * |[20]    |OPMODE    |Operation Mode Selection
     * |        |          |The OPMODE defines that if the EMAC is operating on 10M or 100M bps mode
     * |        |          |The RST (EMAC_CTL[24]) would not affect OPMODE value.
     * |        |          |0 = EMAC operates in 10Mbps mode.
     * |        |          |1 = EMAC operates in 100Mbps mode.
     * |[22]    |RMIIEN    |RMII Mode Enable Bit
     * |        |          |This bit controls if Ethernet MAC controller connected with off-chip Ethernet PHY by MII
     * |        |          |interface or RMII interface
     * |        |          |The RST (EMAC_CTL[24]) would not affect RMIIEN value.
     * |        |          |0 = Ethernet MAC controller RMII mode Disabled.
     * |        |          |1 = Ethernet MAC controller RMII mode Enabled.
     * |        |          |NOTE: This field must keep 1.
     * |[24]    |RST       |Software Reset
     * |        |          |The RST implements a reset function to make the EMAC return default state
     * |        |          |The RST is a self-clear bit
     * |        |          |This means after the software reset finished, the RST will be cleared automatically
     * |        |          |Enable RST can also reset all control and status registers, exclusive of the control bits
     * |        |          |RMIIEN (EMAC_CTL[22]), and OPMODE (EMAC_CTL[20]).
     * |        |          |The EMAC re-initial is necessary after the software reset completed.
     * |        |          |0 = Software reset completed.
     * |        |          |1 = Software reset Enabled.
     * @var EMAC_T::MIIMDAT
     * Offset: 0x94  MII Management Data Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[15:0]  |DATA      |MII Management Data
     * |        |          |The DATA is the 16 bits data that will be written into the registers of external PHY for MII
     * |        |          |Management write command or the data from the registers of external PHY for MII Management read command.
     * @var EMAC_T::MIIMCTL
     * Offset: 0x98  MII Management Control and Address Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[4:0]   |PHYREG    |PHY Register Address
     * |        |          |The PHYREG keeps the address to indicate which register of external PHY is the target of the
     * |        |          |MII management command.
     * |[12:8]  |PHYADDR   |PHY Address
     * |        |          |The PHYADDR keeps the address to differentiate which external PHY is the target of the MII management command.
     * |[16]    |WRITE     |Write Command
     * |        |          |The Write defines the MII management command is a read or write.
     * |        |          |0 = MII management command is a read command.
     * |        |          |1 = MII management command is a write command.
     * |[17]    |BUSY      |Busy Bit
     * |        |          |The BUSY controls the enable of the MII management frame generation
     * |        |          |If S/W wants to access registers of external PHY, it set BUSY to high and EMAC generates
     * |        |          |the MII management frame to external PHY through MII Management I/F
     * |        |          |The BUSY is a self-clear bit
     * |        |          |This means the BUSY will be cleared automatically after the MII management command finished.
     * |        |          |0 = MII management command generation finished.
     * |        |          |1 = MII management command generation Enabled.
     * |[18]    |PREAMSP   |Preamble Suppress
     * |        |          |The PREAMSP controls the preamble field generation of MII management frame
     * |        |          |If the PREAMSP is set to high, the preamble field generation of MII management frame is skipped.
     * |        |          |0 = Preamble field generation of MII management frame not skipped.
     * |        |          |1 = Preamble field generation of MII management frame skipped.
     * |[19]    |MDCON     |MDC Clock ON
     * |        |          |The MDC controls the MDC clock generation. If the MDCON is set to high, the MDC clock is turned on.
     * |        |          |0 = MDC clock off.
     * |        |          |1 = MDC clock on.
     * @var EMAC_T::FIFOCTL
     * Offset: 0x9C  FIFO Threshold Control Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[1:0]   |RXFIFOTH  |RXFIFO Low Threshold
     * |        |          |The RXFIFOTH controls when RXDMA requests internal arbiter for data transfer between RXFIFO
     * |        |          |and system memory
     * |        |          |The RXFIFOTH defines not only the high threshold of RXFIFO, but also the low threshold
     * |        |          |The low threshold is the half of high threshold always
     * |        |          |During the packet reception, if the RXFIFO reaches the high threshold, the RXDMA starts to
     * |        |          |transfer frame data from RXFIFO to system memory
     * |        |          |If the frame data in RXFIFO is less than low threshold, RXDMA stops to transfer the frame
     * |        |          |data to system memory.
     * |        |          |00 = Depend on the burst length setting
     * |        |          |If the burst length is 8 words, high threshold is 8 words, too.
     * |        |          |01 = RXFIFO high threshold is 64B and low threshold is 32B.
     * |        |          |10 = RXFIFO high threshold is 128B and low threshold is 64B.
     * |        |          |11 = RXFIFO high threshold is 192B and low threshold is 96B.
     * |[9:8]   |TXFIFOTH  |TXFIFO Low Threshold
     * |        |          |The TXFIFOTH controls when TXDMA requests internal arbiter for data transfer between system
     * |        |          |memory and TXFIFO
     * |        |          |The TXFIFOTH defines not only the low threshold of TXFIFO, but also the high threshold
     * |        |          |The high threshold is the twice of low threshold always
     * |        |          |During the packet transmission, if the TXFIFO reaches the high threshold, the TXDMA stops
     * |        |          |generate request to transfer frame data from system memory to TXFIFO
     * |        |          |If the frame data in TXFIFO is less than low threshold, TXDMA starts to transfer frame data
     * |        |          |from system memory to TXFIFO.
     * |        |          |The TXFIFOTH also defines when the TXMAC starts to transmit frame out to network
     * |        |          |The TXMAC starts to transmit the frame out while the TXFIFO first time reaches the high threshold
     * |        |          |during the transmission of the frame
     * |        |          |If the frame data length is less than TXFIFO high threshold, the TXMAC starts to transmit the frame
     * |        |          |out after the frame data are all inside the TXFIFO.
     * |        |          |00 = Undefined.
     * |        |          |01 = TXFIFO low threshold is 64B and high threshold is 128B.
     * |        |          |10 = TXFIFO low threshold is 80B and high threshold is 160B.
     * |        |          |11 = TXFIFO low threshold is 96B and high threshold is 192B.
     * |[21:20] |BURSTLEN  |DMA Burst Length
     * |        |          |This defines the burst length of AHB bus cycle while EMAC accesses system memory.
     * |        |          |00 = 4 words.
     * |        |          |01 = 8 words.
     * |        |          |10 = 16 words.
     * |        |          |11 = 16 words.
     * @var EMAC_T::TXST
     * Offset: 0xA0  Transmit Start Demand Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |TXST      |Transmit Start Demand
     * |        |          |If the TX descriptor is not available for use of TXDMA after the TXON (EMAC_CTL[8]) is enabled,
     * |        |          |the FSM (Finite State Machine) of TXDMA enters the Halt state and the frame transmission is halted
     * |        |          |After the S/W has prepared the new TX descriptor for frame transmission, it must issue a write
     * |        |          |command to EMAC_TXST register to make TXDMA to leave Halt state and continue the frame transmission.
     * |        |          |The EMAC_TXST is a write only register and read from this register is undefined.
     * |        |          |The write to EMAC_TXST register takes effect only when TXDMA stayed at Halt state.
     * @var EMAC_T::RXST
     * Offset: 0xA4  Receive Start Demand Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |RXST      |Receive Start Demand
     * |        |          |If the RX descriptor is not available for use of RXDMA after the RXON (EMAC_CTL[0]) is enabled,
     * |        |          |the FSM (Finite State Machine) of RXDMA enters the Halt state and the frame reception is halted
     * |        |          |After the S/W has prepared the new RX descriptor for frame reception, it must issue a write
     * |        |          |command to EMAC_RXST register to make RXDMA to leave Halt state and continue the frame reception.
     * |        |          |The EMAC_RXST is a write only register and read from this register is undefined.
     * |        |          |The write to EMAC_RXST register take effect only when RXDMA stayed at Halt state.
     * @var EMAC_T::MRFL
     * Offset: 0xA8  Maximum Receive Frame Control Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[15:0]  |MRFL      |Maximum Receive Frame Length
     * |        |          |The MRFL defines the maximum frame length for received frame
     * |        |          |If the frame length of received frame is greater than MRFL, and bit MFLEIEN (EMAC_INTEN[8])
     * |        |          |is also enabled, the bit MFLEIF (EMAC_INTSTS[8]) is set and the RX interrupt is triggered.
     * |        |          |It is recommended that only use MRFL to qualify the length of received frame while S/W wants to
     * |        |          |receive a frame which length is greater than 1518 bytes.
     * @var EMAC_T::INTEN
     * Offset: 0xAC  MAC Interrupt Enable Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[0]     |RXIEN     |Receive Interrupt Enable Bit
     * |        |          |The RXIEN controls the RX interrupt generation.
     * |        |          |If RXIEN is enabled and RXIF (EMAC_INTSTS[0]) is high, EMAC generates the RX interrupt to CPU
     * |        |          |If RXIEN is disabled, no RX interrupt is generated to CPU even any status bit EMAC_INTSTS[15:1]
     * |        |          |is set and the corresponding bit of EMAC_INTEN is enabled
     * |        |          |In other words, if S/W wants to receive RX interrupt from EMAC, this bit must be enabled
     * |        |          |And, if S/W doesn't want to receive any RX interrupt from EMAC, disables this bit.
     * |        |          |0 = RXIF (EMAC_INTSTS[0]) is masked and RX interrupt generation Disabled.
     * |        |          |1 = RXIF (EMAC_INTSTS[0]) is not masked and RX interrupt generation Enabled.
     * |[1]     |CRCEIEN   |CRC Error Interrupt Enable Bit
     * |        |          |The CRCEIEN controls the CRCEIF (EMAC_INTSTS[1]) interrupt generation
     * |        |          |If CRCEIF (EMAC_INTSTS[1]) is set, and both CRCEIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If CRCEIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |CRCEIF (EMAC_INTSTS[1]) is set.
     * |        |          |0 = CRCEIF (EMAC_INTSTS[1]) trigger RX interrupt Disabled.
     * |        |          |1 = CRCEIF (EMAC_INTSTS[1]) trigger RX interrupt Enabled.
     * |[2]     |RXOVIEN   |Receive FIFO Overflow Interrupt Enable Bit
     * |        |          |The RXOVIEN controls the RXOVIF (EMAC_INTSTS[2]) interrupt generation
     * |        |          |If RXOVIF (EMAC_INTSTS[2]) is set, and both RXOVIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If RXOVIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |RXOVIF (EMAC_INTSTS[2]) is set.
     * |        |          |0 = RXOVIF (EMAC_INTSTS[2]) trigger RX interrupt Disabled.
     * |        |          |1 = RXOVIF (EMAC_INTSTS[2]) trigger RX interrupt Enabled.
     * |[3]     |LPIEN     |Long Packet Interrupt Enable Bit
     * |        |          |The LPIEN controls the LPIF (EMAC_INTSTS[3]) interrupt generation
     * |        |          |If LPIF (EMAC_INTSTS[3]) is set, and both LPIEN and RXIEN (EMAC_INTEN[0]) are enabled, the EMAC
     * |        |          |generates the RX interrupt to CPU
     * |        |          |If LPIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the LPIF
     * |        |          |(EMAC_INTSTS[3]) is set.
     * |        |          |0 = LPIF (EMAC_INTSTS[3]) trigger RX interrupt Disabled.
     * |        |          |1 = LPIF (EMAC_INTSTS[3]) trigger RX interrupt Enabled.
     * |[4]     |RXGDIEN   |Receive Good Interrupt Enable Bit
     * |        |          |The RXGDIEN controls the RXGDIF (EMAC_INTSTS[4]) interrupt generation
     * |        |          |If RXGDIF (EMAC_INTSTS[4]) is set, and both RXGDIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If RXGDIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |RXGDIF (EMAC_INTSTS[4]) is set.
     * |        |          |0 = RXGDIF (EMAC_INTSTS[4]) trigger RX interrupt Disabled.
     * |        |          |1 = RXGDIF (EMAC_INTSTS[4]) trigger RX interrupt Enabled.
     * |[5]     |ALIEIEN   |Alignment Error Interrupt Enable Bit
     * |        |          |The ALIEIEN controls the ALIEIF (EMAC_INTSTS[5]) interrupt generation
     * |        |          |If ALIEIF (EMAC_INTSTS[5]) is set, and both ALIEIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If ALIEIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |ALIEIF (EMAC_INTSTS[5]) is set.
     * |        |          |0 = ALIEIF (EMAC_INTSTS[5]) trigger RX interrupt Disabled.
     * |        |          |1 = ALIEIF (EMAC_INTSTS[5]) trigger RX interrupt Enabled.
     * |[6]     |RPIEN     |Runt Packet Interrupt Enable Bit
     * |        |          |The RPIEN controls the RPIF (EMAC_INTSTS[6]) interrupt generation
     * |        |          |If RPIF (EMAC_INTSTS[6]) is set, and both RPIEN and RXIEN (EMAC_INTEN[0]) are enabled, the EMAC
     * |        |          |generates the RX interrupt to CPU
     * |        |          |If RPIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |RPIF (EMAC_INTSTS[6]) is set.
     * |        |          |0 = RPIF (EMAC_INTSTS[6]) trigger RX interrupt Disabled.
     * |        |          |1 = RPIF (EMAC_INTSTS[6]) trigger RX interrupt Enabled.
     * |[7]     |MPCOVIEN  |Miss Packet Counter Overrun Interrupt Enable Bit
     * |        |          |The MPCOVIEN controls the MPCOVIF (EMAC_INTSTS[7]) interrupt generation
     * |        |          |If MPCOVIF (EMAC_INTSTS[7]) is set, and both MPCOVIEN and RXIEN (EMAC_INTEN[0]) are enabled,
     * |        |          |the EMAC generates the RX interrupt to CPU
     * |        |          |If MPCOVIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |MPCOVIF (EMAC_INTSTS[7]) is set.
     * |        |          |0 = MPCOVIF (EMAC_INTSTS[7]) trigger RX interrupt Disabled.
     * |        |          |1 = MPCOVIF (EMAC_INTSTS[7]) trigger RX interrupt Enabled.
     * |[8]     |MFLEIEN   |Maximum Frame Length Exceed Interrupt Enable Bit
     * |        |          |The MFLEIEN controls the MFLEIF (EMAC_INTSTS[8]) interrupt generation
     * |        |          |If MFLEIF (EMAC_INTSTS[8]) is set, and both MFLEIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If MFLEIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |MFLEIF (EMAC_INTSTS[8]) is set.
     * |        |          |0 = MFLEIF (EMAC_INTSTS[8]) trigger RX interrupt Disabled.
     * |        |          |1 = MFLEIF (EMAC_INTSTS[8]) trigger RX interrupt Enabled.
     * |[9]     |DENIEN    |DMA Early Notification Interrupt Enable Bit
     * |        |          |The DENIEN controls the DENIF (EMAC_INTSTS[9]) interrupt generation
     * |        |          |If DENIF (EMAC_INTSTS[9]) is set, and both DENIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If DENIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |DENIF (EMAC_INTSTS[9]) is set.
     * |        |          |0 = TDENIF (EMAC_INTSTS[9]) trigger RX interrupt Disabled.
     * |        |          |1 = TDENIF (EMAC_INTSTS[9]) trigger RX interrupt Enabled.
     * |[10]    |RDUIEN    |Receive Descriptor Unavailable Interrupt Enable Bit
     * |        |          |The RDUIEN controls the RDUIF (EMAC_INTSTS[10]) interrupt generation
     * |        |          |If RDUIF (EMAC_INTSTS[10]) is set, and both RDUIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If RDUIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |RDUIF (EMAC_MIOSTA[10]) register is set.
     * |        |          |0 = RDUIF (EMAC_INTSTS[10]) trigger RX interrupt Disabled.
     * |        |          |1 = RDUIF (EMAC_INTSTS[10]) trigger RX interrupt Enabled.
     * |[11]    |RXBEIEN   |Receive Bus Error Interrupt Enable Bit
     * |        |          |The RXBEIEN controls the RXBEIF (EMAC_INTSTS[11]) interrupt generation
     * |        |          |If RXBEIF (EMAC_INTSTS[11]) is set, and both RXBEIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If RXBEIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |RXBEIF (EMAC_INTSTS[11]) is set.
     * |        |          |0 = RXBEIF (EMAC_INTSTS[11]) trigger RX interrupt Disabled.
     * |        |          |1 = RXBEIF (EMAC_INTSTS[11]) trigger RX interrupt Enabled.
     * |[14]    |CFRIEN    |Control Frame Receive Interrupt Enable Bit
     * |        |          |The CFRIEN controls the CFRIF (EMAC_INTSTS[14]) interrupt generation
     * |        |          |If CFRIF (EMAC_INTSTS[14]) is set, and both CFRIEN and RXIEN (EMAC_INTEN[0]) are enabled, the
     * |        |          |EMAC generates the RX interrupt to CPU
     * |        |          |If CFRIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |CFRIF (EMAC_INTSTS[14]) register is set.
     * |        |          |0 = CFRIF (EMAC_INTSTS[14]) trigger RX interrupt Disabled.
     * |        |          |1 = CFRIF (EMAC_INTSTS[14]) trigger RX interrupt Enabled.
     * |[15]    |WOLIEN    |Wake on LAN Interrupt Enable Bit
     * |        |          |The WOLIEN controls the WOLIF (EMAC_INTSTS[15]) interrupt generation
     * |        |          |If WOLIF (EMAC_INTSTS[15]) is set, and both WOLIEN and RXIEN (EMAC_INTEN[0]) are enabled,
     * |        |          |the EMAC generates the RX interrupt to CPU
     * |        |          |If WOLIEN or RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated to CPU even the
     * |        |          |WOLIF (EMAC_INTSTS[15]) is set.
     * |        |          |0 = WOLIF (EMAC_INTSTS[15]) trigger RX interrupt Disabled.
     * |        |          |1 = WOLIF (EMAC_INTSTS[15]) trigger RX interrupt Enabled.
     * |[16]    |TXIEN     |Transmit Interrupt Enable Bit
     * |        |          |The TXIEN controls the TX interrupt generation.
     * |        |          |If TXIEN is enabled and TXIF (EMAC_INTSTS[16]) is high, EMAC generates the TX interrupt to CPU
     * |        |          |If TXIEN is disabled, no TX interrupt is generated to CPU even any status bit of
     * |        |          |EMAC_INTSTS[24:17] set and the corresponding bit of EMAC_INTEN is enabled
     * |        |          |In other words, if S/W wants to receive TX interrupt from EMAC, this bit must be enabled
     * |        |          |And, if S/W doesn't want to receive any TX interrupt from EMAC, disables this bit.
     * |        |          |0 = TXIF (EMAC_INTSTS[16]) is masked and TX interrupt generation Disabled.
     * |        |          |1 = TXIF (EMAC_INTSTS[16]) is not masked and TX interrupt generation Enabled.
     * |[17]    |TXUDIEN   |Transmit FIFO Underflow Interrupt Enable Bit
     * |        |          |The TXUDIEN controls the TXUDIF (EMAC_INTSTS[17]) interrupt generation
     * |        |          |If TXUDIF (EMAC_INTSTS[17]) is set, and both TXUDIEN and TXIEN (EMAC_INTEN[16]) are enabled,
     * |        |          |the EMAC generates the TX interrupt to CPU
     * |        |          |If TXUDIEN or TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated to CPU even
     * |        |          |the TXUDIF (EMAC_INTSTS[17]) is set.
     * |        |          |0 = TXUDIF (EMAC_INTSTS[17]) TX interrupt Disabled.
     * |        |          |1 = TXUDIF (EMAC_INTSTS[17]) TX interrupt Enabled.
     * |[18]    |TXCPIEN   |Transmit Completion Interrupt Enable Bit
     * |        |          |The TXCPIEN controls the TXCPIF (EMAC_INTSTS[18]) interrupt generation
     * |        |          |If TXCPIF (EMAC_INTSTS[18]) is set, and both TXCPIEN and TXIEN (EMAC_INTEN[16]) are enabled,
     * |        |          |the EMAC generates the TX interrupt to CPU
     * |        |          |If TXCPIEN or TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated to CPU even the
     * |        |          |TXCPIF (EMAC_INTSTS[18]) is set.
     * |        |          |0 = TXCPIF (EMAC_INTSTS[18]) trigger TX interrupt Disabled.
     * |        |          |1 = TXCPIF (EMAC_INTSTS[18]) trigger TX interrupt Enabled.
     * |[19]    |EXDEFIEN  |Defer Exceed Interrupt Enable Bit
     * |        |          |The EXDEFIEN controls the EXDEFIF (EMAC_INTSTS[19]) interrupt generation
     * |        |          |If EXDEFIF (EMAC_INTSTS[19]) is set, and both EXDEFIEN and TXIEN (EMAC_INTEN[16]) are enabled,
     * |        |          |the EMAC generates the TX interrupt to CPU
     * |        |          |If EXDEFIEN or TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated to CPU even the
     * |        |          |EXDEFIF (EMAC_INTSTS[19]) is set.
     * |        |          |0 = EXDEFIF (EMAC_INTSTS[19]) trigger TX interrupt Disabled.
     * |        |          |1 = EXDEFIF (EMAC_INTSTS[19]) trigger TX interrupt Enabled.
     * |[20]    |NCSIEN    |No Carrier Sense Interrupt Enable Bit
     * |        |          |The NCSIEN controls the NCSIF (EMAC_INTSTS[20]) interrupt generation
     * |        |          |If NCSIF (EMAC_INTSTS[20]) is set, and both NCSIEN and TXIEN (EMAC_INTEN[16]) are enabled, the
     * |        |          |EMAC generates the TX interrupt to CPU
     * |        |          |If NCSIEN or TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated to CPU even the
     * |        |          |NCSIF (EMAC_INTSTS[20]) is set.
     * |        |          |0 = NCSIF (EMAC_INTSTS[20]) trigger TX interrupt Disabled.
     * |        |          |1 = NCSIF (EMAC_INTSTS[20]) trigger TX interrupt Enabled.
     * |[21]    |TXABTIEN  |Transmit Abort Interrupt Enable Bit
     * |        |          |The TXABTIEN controls the TXABTIF (EMAC_INTSTS[21]) interrupt generation
     * |        |          |If TXABTIF (EMAC_INTSTS[21]) is set, and both TXABTIEN and TXIEN (EMAC_INTEN[16]) are enabled,
     * |        |          |the EMAC generates the TX interrupt to CPU
     * |        |          |If TXABTIEN or TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated to CPU even the
     * |        |          |TXABTIF (EMAC_INTSTS[21]) is set.
     * |        |          |0 = TXABTIF (EMAC_INTSTS[21]) trigger TX interrupt Disabled.
     * |        |          |1 = TXABTIF (EMAC_INTSTS[21]) trigger TX interrupt Enabled.
     * |[22]    |LCIEN     |Late Collision Interrupt Enable Bit
     * |        |          |The LCIEN controls the LCIF (EMAC_INTSTS[22]) interrupt generation
     * |        |          |If LCIF (EMAC_INTSTS[22]) is set, and both LCIEN and TXIEN (EMAC_INTEN[16]) are enabled, the
     * |        |          |EMAC generates the TX interrupt to CPU
     * |        |          |If LCIEN or TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated to CPU even the
     * |        |          |LCIF (EMAC_INTSTS[22]) is set.
     * |        |          |0 = LCIF (EMAC_INTSTS[22]) trigger TX interrupt Disabled.
     * |        |          |1 = LCIF (EMAC_INTSTS[22]) trigger TX interrupt Enabled.
     * |[23]    |TDUIEN    |Transmit Descriptor Unavailable Interrupt Enable Bit
     * |        |          |The TDUIEN controls the TDUIF (EMAC_INTSTS[23]) interrupt generation
     * |        |          |If TDUIF (EMAC_INTSTS[23]) is set, and both TDUIEN and TXIEN (EMAC_INTEN[16]) are enabled, the
     * |        |          |EMAC generates the TX interrupt to CPU
     * |        |          |If TDUIEN or TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated to CPU even the
     * |        |          |TDUIF (EMAC_INTSTS[23]) is set.
     * |        |          |0 = TDUIF (EMAC_INTSTS[23]) trigger TX interrupt Disabled.
     * |        |          |1 = TDUIF (EMAC_INTSTS[23]) trigger TX interrupt Enabled.
     * |[24]    |TXBEIEN   |Transmit Bus Error Interrupt Enable Bit
     * |        |          |The TXBEIEN controls the TXBEIF (EMAC_INTSTS[24]) interrupt generation
     * |        |          |If TXBEIF (EMAC_INTSTS[24]) is set, and both TXBEIEN and TXIEN (EMAC_INTEN[16]) are enabled, the
     * |        |          |EMAC generates the TX interrupt to CPU
     * |        |          |If TXBEIEN or TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated to CPU even the
     * |        |          |TXBEIF (EMAC_INTSTS[24]) is set.
     * |        |          |0 = TXBEIF (EMAC_INTSTS[24]) trigger TX interrupt Disabled.
     * |        |          |1 = TXBEIF (EMAC_INTSTS[24]) trigger TX interrupt Enabled.
     * |[28]    |TSALMIEN  |Time Stamp Alarm Interrupt Enable Bit
     * |        |          |The TSALMIEN controls the TSALMIF (EMAC_INTSTS[28]) interrupt generation
     * |        |          |If TSALMIF (EMAC_INTSTS[28]) is set, and both TSALMIEN and TXIEN (EMAC_INTEN[16]) enabled, the
     * |        |          |EMAC generates the TX interrupt to CPU
     * |        |          |If TSALMIEN or TXIEN (EMAC_INTEN[16]) disabled, no TX interrupt generated to CPU even the
     * |        |          |TXTSALMIF (EMAC_INTEN[28]) is set.
     * |        |          |0 = TXTSALMIF (EMAC_INTSTS[28]) trigger TX interrupt Disabled.
     * |        |          |1 = TXTSALMIF (EMAC_INTSTS[28]) trigger TX interrupt Enabled.
     * @var EMAC_T::INTSTS
     * Offset: 0xB0  MAC Interrupt Status Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[0]     |RXIF      |Receive Interrupt
     * |        |          |The RXIF indicates the RX interrupt status.
     * |        |          |If RXIF high and its corresponding enable bit, RXIEN (EMAC_INTEN[0]), is also high indicates
     * |        |          |the EMAC generates RX interrupt to CPU
     * |        |          |If RXIF is high but RXIEN (EMAC_INTEN[0]) is disabled, no RX interrupt is generated.
     * |        |          |The RXIF is logic OR result of bit logic AND result of EMAC_INTSTS[15:1] and EMAC_INTEN[15:1]
     * |        |          |In other words, if any bit of EMAC_INTSTS[15:1] is high and its corresponding enable bit in
     * |        |          |EMAC_INTEN[15:1] is also enabled, the RXIF will be high.
     * |        |          |Because the RXIF is a logic OR result, clears EMAC_INTSTS[15:1] makes RXIF be cleared, too.
     * |        |          |0 = No status bit in EMAC_INTSTS[15:1] is set or no enable bit in EMAC_INTEN[15:1] is enabled.
     * |        |          |1 = At least one status in EMAC_INTSTS[15:1] is set and its corresponding enable bit in
     * |        |          |EMAC_INTEN[15:1] is enabled, too.
     * |[1]     |CRCEIF    |CRC Error Interrupt
     * |        |          |The CRCEIF high indicates the incoming packet incurred the CRC error and the packet is dropped
     * |        |          |If the AEP (EMAC_CTL[4]) is set, the CRC error packet will be regarded as a good packet and
     * |        |          |CRCEIF will not be set.
     * |        |          |If the CRCEIF is high and CRCEIEN (EMAC_INTEN[1]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the CRCEIF status.
     * |        |          |0 = The frame does not incur CRC error.
     * |        |          |1 = The frame incurred CRC error.
     * |[2]     |RXOVIF    |Receive FIFO Overflow Interrupt
     * |        |          |The RXOVIF high indicates the RXFIFO overflow occurred during packet reception
     * |        |          |While the RXFIFO overflow occurred, the EMAC drops the current receiving packer
     * |        |          |If the RXFIFO overflow occurred often, it is recommended that modify RXFIFO threshold control,
     * |        |          |the RXFIFOTH of FFTCR register, to higher level.
     * |        |          |If the RXOVIF is high and RXOVIEN (EMAC_INTEN[2]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the RXOVIF status.
     * |        |          |0 = No RXFIFO overflow occurred during packet reception.
     * |        |          |1 = RXFIFO overflow occurred during packet reception.
     * |[3]     |LPIF      |Long Packet Interrupt Flag
     * |        |          |The LPIF high indicates the length of the incoming packet is greater than 1518 bytes and the
     * |        |          |incoming packet is dropped
     * |        |          |If the ALP (EMAC_CTL[1]) is set, the long packet will be regarded as a good packet and LPIF will not be set.
     * |        |          |If the LPIF is high and LPIEN (EMAC_INTEN[3]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the LPIF status.
     * |        |          |0 = The incoming frame is not a long frame or S/W wants to receive a long frame.
     * |        |          |1 = The incoming frame is a long frame and dropped.
     * |[4]     |RXGDIF    |Receive Good Interrupt
     * |        |          |The RXGDIF high indicates the frame reception has completed.
     * |        |          |If the RXGDIF is high and RXGDIEN (EAMC_MIEN[4]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the RXGDIF status.
     * |        |          |0 = The frame reception has not complete yet.
     * |        |          |1 = The frame reception has completed.
     * |[5]     |ALIEIF    |Alignment Error Interrupt
     * |        |          |The ALIEIF high indicates the length of the incoming frame is not a multiple of byte
     * |        |          |If the ALIEIF is high and ALIEIEN (EMAC_INTEN[5]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the ALIEIF status.
     * |        |          |0 = The frame length is a multiple of byte.
     * |        |          |1 = The frame length is not a multiple of byte.
     * |[6]     |RPIF      |Runt Packet Interrupt
     * |        |          |The RPIF high indicates the length of the incoming packet is less than 64 bytes and the packet is dropped
     * |        |          |If the ARP (EMAC_CTL[2]) is set, the short packet is regarded as a good packet and RPIF will not be set.
     * |        |          |If the RPIF is high and RPIEN (EMAC_INTEN[6]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the RPIF status.
     * |        |          |0 = The incoming frame is not a short frame or S/W wants to receive a short frame.
     * |        |          |1 = The incoming frame is a short frame and dropped.
     * |[7]     |MPCOVIF   |Missed Packet Counter Overrun Interrupt Flag
     * |        |          |The MPCOVIF high indicates the MPCNT, Missed Packet Count, has overflow
     * |        |          |If the MPCOVIF is high and MPCOVIEN (EMAC_INTEN[7]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the MPCOVIF status.
     * |        |          |0 = The MPCNT has not rolled over yet.
     * |        |          |1 = The MPCNT has rolled over yet.
     * |[8]     |MFLEIF    |Maximum Frame Length Exceed Interrupt Flag
     * |        |          |The MFLEIF high indicates the length of the incoming packet has exceeded the length limitation
     * |        |          |configured in DMARFC register and the incoming packet is dropped
     * |        |          |If the MFLEIF is high and MFLEIEN (EMAC_INTEN[8]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the MFLEIF status.
     * |        |          |0 = The length of the incoming packet does not exceed the length limitation configured in DMARFC.
     * |        |          |1 = The length of the incoming packet has exceeded the length limitation configured in DMARFC.
     * |[9]     |DENIF     |DMA Early Notification Interrupt
     * |        |          |The DENIF high indicates the EMAC has received the LENGTH field of the incoming packet.
     * |        |          |If the DENIF is high and DENIENI (EMAC_INTEN[9]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the DENIF status.
     * |        |          |0 = The LENGTH field of incoming packet has not received yet.
     * |        |          |1 = The LENGTH field of incoming packet has received.
     * |[10]    |RDUIF     |Receive Descriptor Unavailable Interrupt
     * |        |          |The RDUIF high indicates that there is no available RX descriptor for packet reception and
     * |        |          |RXDMA will stay at Halt state
     * |        |          |Once, the RXDMA enters the Halt state, S/W must issues a write command to RSDR register to
     * |        |          |make RXDMA leave Halt state while new RX descriptor is available.
     * |        |          |If the RDUIF is high and RDUIEN (EMAC_INTEN[10]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the RDUIF status.
     * |        |          |0 = RX descriptor is available.
     * |        |          |1 = RX descriptor is unavailable.
     * |[11]    |RXBEIF    |Receive Bus Error Interrupt
     * |        |          |The RXBEIF high indicates the memory controller replies ERROR response while EMAC access
     * |        |          |system memory through RXDMA during packet reception process
     * |        |          |Reset EMAC is recommended while RXBEIF status is high.
     * |        |          |If the RXBEIF is high and RXBEIEN (EMAC_INTEN[11]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the RXBEIF status.
     * |        |          |0 = No ERROR response is received.
     * |        |          |1 = ERROR response is received.
     * |[14]    |CFRIF     |Control Frame Receive Interrupt
     * |        |          |The CFRIF high indicates EMAC receives a flow control frame
     * |        |          |The CFRIF only available while EMAC is operating on full duplex mode.
     * |        |          |If the CFRIF is high and CFRIEN (EMAC_INTEN[14]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the CFRIF status.
     * |        |          |0 = The EMAC does not receive the flow control frame.
     * |        |          |1 = The EMAC receives a flow control frame.
     * |[15]    |WOLIF     |Wake on LAN Interrupt Flag
     * |        |          |The WOLIF high indicates EMAC receives a Magic Packet
     * |        |          |The CFRIF only available while system is in power down mode and WOLEN is set high.
     * |        |          |If the WOLIF is high and WOLIEN (EMAC_INTEN[15]) is enabled, the RXIF will be high
     * |        |          |Write 1 to this bit clears the WOLIF status.
     * |        |          |0 = The EMAC does not receive the Magic Packet.
     * |        |          |1 = The EMAC receives a Magic Packet.
     * |[16]    |TXIF      |Transmit Interrupt
     * |        |          |The TXIF indicates the TX interrupt status.
     * |        |          |If TXIF high and its corresponding enable bit, TXIEN (EMAC_INTEN[16]), is also high indicates
     * |        |          |the EMAC generates TX interrupt to CPU
     * |        |          |If TXIF is high but TXIEN (EMAC_INTEN[16]) is disabled, no TX interrupt is generated.
     * |        |          |The TXIF is logic OR result of bit logic AND result of EMAC_INTSTS[28:17] and EMAC_INTEN[28:17]
     * |        |          |In other words, if any bit of EMAC_INTSTS[28:17] is high and its corresponding enable bit
     * |        |          |in EMAC_INTEN[28:17] is also enabled, the TXIF will be high
     * |        |          |Because the TXIF is a logic OR result, clears EMAC_INTSTS[28:17] makes TXIF be cleared, too.
     * |        |          |0 = No status bit in EMAC_INTSTS[28:17] is set or no enable bit in EMAC_INTEN[28:17] is enabled.
     * |        |          |1 = At least one status in EMAC_INTSTS[28:17] is set and its corresponding enable bit
     * |        |          |in EMAC_INTEN[28:17] is enabled, too.
     * |[17]    |TXUDIF    |Transmit FIFO Underflow Interrupt
     * |        |          |The TXUDIF high indicates the TXFIFO underflow occurred during packet transmission
     * |        |          |While the TXFIFO underflow occurred, the EMAC will retransmit the packet automatically
     * |        |          |without S/W intervention
     * |        |          |If the TXFIFO underflow occurred often, it is recommended that modify TXFIFO threshold control,
     * |        |          |the TXFIFOTH of FFTCR register, to higher level.
     * |        |          |If the TXUDIF is high and TXUDIEN (EMAC_INTEN[17]) is enabled, the TXIF will be high
     * |        |          |Write 1 to this bit clears the TXUDIF status.
     * |        |          |0 = No TXFIFO underflow occurred during packet transmission.
     * |        |          |1 = TXFIFO underflow occurred during packet transmission.
     * |[18]    |TXCPIF    |Transmit Completion Interrupt
     * |        |          |The TXCPIF indicates the packet transmission has completed correctly.
     * |        |          |If the TXCPIF is high and TXCPIEN (EMAC_INTEN[18]) is enabled, the TXIF will be high
     * |        |          |Write 1 to this bit clears the TXCPIF status.
     * |        |          |0 = The packet transmission not completed.
     * |        |          |1 = The packet transmission has completed.
     * |[19]    |EXDEFIF   |Defer Exceed Interrupt
     * |        |          |The EXDEFIF high indicates the frame waiting for transmission has deferred over 0.32768ms
     * |        |          |on 100Mbps mode, or 3.2768ms on 10Mbps mode.
     * |        |          |The deferral exceed check will only be done while bit NODEF of MCMDR is disabled, and EMAC
     * |        |          |is operating on half-duplex mode.
     * |        |          |If the EXDEFIF is high and EXDEFIEN (EMAC_INTEN[19]) is enabled, the TXIF will be high
     * |        |          |Write 1 to this bit clears the EXDEFIF status.
     * |        |          |0 = Frame waiting for transmission has not deferred over 0.32768ms (100Mbps) or 3.2768ms (10Mbps).
     * |        |          |1 = Frame waiting for transmission has deferred over 0.32768ms (100Mbps) or 3.2768ms (10Mbps).
     * |[20]    |NCSIF     |No Carrier Sense Interrupt
     * |        |          |The NCSIF high indicates the MII I/F signal CRS does not active at the start of or during
     * |        |          |the packet transmission
     * |        |          |The NCSIF is only available while EMAC is operating on half-duplex mode
     * |        |          |If the NCSIF is high and NCSIEN (EMAC_INTEN[20]) is enabled, the TXIF will be high.
     * |        |          |Write 1 to this bit clears the NCSIF status.
     * |        |          |0 = CRS signal actives correctly.
     * |        |          |1 = CRS signal does not active at the start of or during the packet transmission.
     * |[21]    |TXABTIF   |Transmit Abort Interrupt
     * |        |          |The TXABTIF high indicates the packet incurred 16 consecutive collisions during transmission,
     * |        |          |and then the transmission process for this packet is aborted
     * |        |          |The transmission abort is only available while EMAC is operating on half-duplex mode.
     * |        |          |If the TXABTIF is high and TXABTIEN (EMAC_INTEN[21]) is enabled, the TXIF will be high
     * |        |          |Write 1 to this bit clears the TXABTIF status.
     * |        |          |0 = Packet does not incur 16 consecutive collisions during transmission.
     * |        |          |1 = Packet incurred 16 consecutive collisions during transmission.
     * |[22]    |LCIF      |Late Collision Interrupt
     * |        |          |The LCIF high indicates the collision occurred in the outside of 64 bytes collision window
     * |        |          |This means after the 64 bytes of a frame has been transmitted out to the network, the collision
     * |        |          |still occurred.
     * |        |          |The late collision check will only be done while EMAC is operating on half-duplex mode
     * |        |          |If the LCIF is high and LCIEN (EMAC_INTEN[22]) is enabled, the TXIF will be high.
     * |        |          |Write 1 to this bit clears the LCIF status.
     * |        |          |0 = No collision occurred in the outside of 64 bytes collision window.
     * |        |          |1 = Collision occurred in the outside of 64 bytes collision window.
     * |[23]    |TDUIF     |Transmit Descriptor Unavailable Interrupt
     * |        |          |The TDUIF high indicates that there is no available TX descriptor for packet transmission and
     * |        |          |TXDMA will stay at Halt state.
     * |        |          |Once, the TXDMA enters the Halt state, S/W must issues a write command to TSDR register to make
     * |        |          |TXDMA leave Halt state while new TX descriptor is available.
     * |        |          |If the TDUIF is high and TDUIEN (EMAC_INTEN[23]) is enabled, the TXIF will be high.
     * |        |          |Write 1 to this bit clears the TDUIF status.
     * |        |          |0 = TX descriptor is available.
     * |        |          |1 = TX descriptor is unavailable.
     * |[24]    |TXBEIF    |Transmit Bus Error Interrupt
     * |        |          |The TXBEIF high indicates the memory controller replies ERROR response while EMAC access system
     * |        |          |memory through TXDMA during packet transmission process
     * |        |          |Reset EMAC is recommended while TXBEIF status is high.
     * |        |          |If the TXBEIF is high and TXBEIEN (EMAC_INTEN[24]) is enabled, the TXIF will be high.
     * |        |          |Write 1 to this bit clears the TXBEIF status.
     * |        |          |0 = No ERROR response is received.
     * |        |          |1 = ERROR response is received.
     * |[28]    |TSALMIF   |Time Stamp Alarm Interrupt
     * |        |          |The TSALMIF high indicates the EMAC_TSSEC register value equals to EMAC_ALMSEC register and
     * |        |          |EMAC_TSSUBSEC register value equals to register EMAC_ALMSUBLSR.
     * |        |          |If TSALMIF is high and TSALMIEN (EMAC_INTEN[28]) enabled, the TXIF will be high.
     * |        |          |Write 1 to this bit clears the TSALMIF status.
     * |        |          |0 = EMAC_TSSEC did not equal EMAC_ALMSEC or EMAC_TSSUBSEC did not equal EMAC_ALMSUBSEC.
     * |        |          |1 = EMAC_TSSEC equals EMAC_ALMSEC and EMAC_TSSUBSEC equals EMAC_ALMSUBSEC.
     * @var EMAC_T::GENSTS
     * Offset: 0xB4  MAC General Status Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[0]     |CFR       |Control Frame Received
     * |        |          |The CFRIF high indicates EMAC receives a flow control frame
     * |        |          |The CFRIF only available while EMAC is operating on full duplex mode.
     * |        |          |0 = The EMAC does not receive the flow control frame.
     * |        |          |1 = The EMAC receives a flow control frame.
     * |[1]     |RXHALT    |Receive Halted
     * |        |          |The RXHALT high indicates the next normal packet reception process will be halted because
     * |        |          |the bit RXON of MCMDR is disabled be S/W.
     * |        |          |0 = Next normal packet reception process will go on.
     * |        |          |1 = Next normal packet reception process will be halted.
     * |[2]     |RXFFULL   |RXFIFO Full
     * |        |          |The RXFFULL indicates the RXFIFO is full due to four 64-byte packets are kept in RXFIFO
     * |        |          |and the following incoming packet will be dropped.
     * |        |          |0 = The RXFIFO is not full.
     * |        |          |1 = The RXFIFO is full and the following incoming packet will be dropped.
     * |[7:4]   |COLCNT    |Collision Count
     * |        |          |The COLCNT indicates that how many collisions occurred consecutively during a packet transmission
     * |        |          |If the packet incurred 16 consecutive collisions during transmission, the COLCNT will be
     * |        |          |0 and bit TXABTIF will be set to 1.
     * |[8]     |DEF       |Deferred Transmission
     * |        |          |The DEF high indicates the packet transmission has deferred once
     * |        |          |The DEF is only available while EMAC is operating on half-duplex mode.
     * |        |          |0 = Packet transmission does not defer.
     * |        |          |1 = Packet transmission has deferred once.
     * |[9]     |TXPAUSED  |Transmission Paused
     * |        |          |The TXPAUSED high indicates the next normal packet transmission process will be paused temporally
     * |        |          |because EMAC received a PAUSE control frame.
     * |        |          |0 = Next normal packet transmission process will go on.
     * |        |          |1 = Next normal packet transmission process will be paused.
     * |[10]    |SQE       |Signal Quality Error
     * |        |          |The SQE high indicates the SQE error found at end of packet transmission on 10Mbps half-duplex mode
     * |        |          |The SQE error check will only be done while both bit SQECHKEN (EMAC_CTL[17]) is enabled and EMAC
     * |        |          |is operating on 10Mbps half-duplex mode.
     * |        |          |0 = No SQE error found at end of packet transmission.
     * |        |          |1 = SQE error found at end of packet transmission.
     * |[11]    |TXHALT    |Transmission Halted
     * |        |          |The TXHALT high indicates the next normal packet transmission process will be halted because
     * |        |          |the bit TXON (EMAC_CTL[8]) is disabled be S/W.
     * |        |          |0 = Next normal packet transmission process will go on.
     * |        |          |1 = Next normal packet transmission process will be halted.
     * |[12]    |RPSTS     |Remote Pause Status
     * |        |          |The RPSTS indicates that remote pause counter down counting actives.
     * |        |          |After Ethernet MAC controller sent PAUSE frame out successfully, it starts the remote pause
     * |        |          |counter down counting
     * |        |          |When this bit high, it's predictable that remote Ethernet MAC controller wouldn't start the packet
     * |        |          |transmission until the down counting done.
     * |        |          |0 = Remote pause counter down counting done.
     * |        |          |1 = Remote pause counter down counting actives.
     * @var EMAC_T::MPCNT
     * Offset: 0xB8  Missed Packet Count Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[15:0]  |MPCNT     |Miss Packet Count
     * |        |          |The MPCNT indicates the number of packets that were dropped due to various types of receive errors
     * |        |          |The following type of receiving error makes missed packet counter increase:
     * |        |          |1. Incoming packet is incurred RXFIFO overflow.
     * |        |          |2. Incoming packet is dropped due to RXON is disabled.
     * |        |          |3. Incoming packet is incurred CRC error.
     * @var EMAC_T::RPCNT
     * Offset: 0xBC  MAC Receive Pause Count Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[15:0]  |RPCNT     |MAC Receive Pause Count
     * |        |          |The RPCNT keeps the OPERAND field of the PAUSE control frame
     * |        |          |It indicates how many slot time (512 bit time) the TX of EMAC will be paused.
     * @var EMAC_T::FRSTS
     * Offset: 0xC8  DMA Receive Frame Status Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[15:0]  |RXFLT     |Receive Frame LENGTH
     * |        |          |The RXFLT keeps the LENGTH field of each incoming Ethernet packet
     * |        |          |If the bit DENIEN (EMAC_INTEN[9]) is enabled and the LENGTH field of incoming packet has
     * |        |          |received, the bit DENIF (EMAC_INTSTS[9]) will be set and trigger interrupt.
     * |        |          |And, the content of LENGTH field will be stored in RXFLT.
     * @var EMAC_T::CTXDSA
     * Offset: 0xCC  Current Transmit Descriptor Start Address Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |CTXDSA    |Current Transmit Descriptor Start Address
     * |        |          |The CTXDSA keeps the start address of TX descriptor that is used by TXDMA currently
     * |        |          |The CTXDSA is read only and write to this register has no effect.
     * @var EMAC_T::CTXBSA
     * Offset: 0xD0  Current Transmit Buffer Start Address Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |CTXBSA    |Current Transmit Buffer Start Address
     * |        |          |The CTXDSA keeps the start address of TX frame buffer that is used by TXDMA currently
     * |        |          |The CTXBSA is read only and write to this register has no effect.
     * @var EMAC_T::CRXDSA
     * Offset: 0xD4  Current Receive Descriptor Start Address Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |CRXDSA    |Current Receive Descriptor Start Address
     * |        |          |The CRXDSA keeps the start address of RX descriptor that is used by RXDMA currently
     * |        |          |The CRXDSA is read only and write to this register has no effect.
     * @var EMAC_T::CRXBSA
     * Offset: 0xD8  Current Receive Buffer Start Address Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |CRXBSA    |Current Receive Buffer Start Address
     * |        |          |The CRXBSA keeps the start address of RX frame buffer that is used by RXDMA currently
     * |        |          |The CRXBSA is read only and write to this register has no effect.
     * @var EMAC_T::TSCTL
     * Offset: 0x100  Time Stamp Control Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[0]     |TSEN      |Time Stamp Function Enable Bit
     * |        |          |This bit controls if the IEEE 1588 PTP time stamp function is enabled or not.
     * |        |          |Set this bit high to enable IEEE 1588 PTP time stamp function while set this bit low
     * |        |          |to disable IEEE 1588 PTP time stamp function.
     * |        |          |0 = I EEE 1588 PTP time stamp function Disabled.
     * |        |          |1 = IEEE 1588 PTP time stamp function Enabled.
     * |[1]     |TSIEN     |Time Stamp Counter Initialization Enable Bit
     * |        |          |Set this bit high enables Ethernet MAC controller to load value of register EMAC_UPDSEC
     * |        |          |and EMAC_UPDSUBSEC to PTP time stamp counter.
     * |        |          |After the load operation finished, Ethernet MAC controller clear this bit to low automatically.
     * |        |          |0 = Time stamp counter initialization done.
     * |        |          |1 = Time stamp counter initialization Enabled.
     * |[2]     |TSMODE    |Time Stamp Fine Update Enable Bit
     * |        |          |This bit chooses the time stamp counter update mode.
     * |        |          |0 = Time stamp counter is in coarse update mode.
     * |        |          |1 = Time stamp counter is in fine update mode.
     * |[3]     |TSUPDATE  |Time Stamp Counter Time Update Enable Bit
     * |        |          |Set this bit high enables Ethernet MAC controller to add value of register EMAC_UPDSEC and
     * |        |          |EMAC_UPDSUBSEC to PTP time stamp counter.
     * |        |          |After the add operation finished, Ethernet MAC controller clear this bit to low automatically.
     * |        |          |0 = No action.
     * |        |          |1 = EMAC_UPDSEC updated to EMAC_TSSEC and EMAC_UPDSUBSEC updated to EMAC_TSSUBSEC.
     * |[5]     |TSALMEN   |Time Stamp Alarm Enable Bit
     * |        |          |Set this bit high enable Ethernet MAC controller to set TSALMIF (EMAC_INTSTS[28]) high when
     * |        |          |EMAC_TSSEC equals to EMAC_ALMSEC and EMAC_TSSUBSEC equals to EMAC_ALMSUBSEC.
     * |        |          |0 = Alarm disabled when EMAC_TSSEC equals to EMAC_ALMSEC and EMAC_TSSUBSEC equals to EMAC_ALMSUBSEC.
     * |        |          |1 = Alarm enabled when EMAC_TSSEC equals to EMAC_ALMSEC and EMAC_TSSUBSEC equals to EMAC_ALMSUBSEC.
     * @var EMAC_T::TSSEC
     * Offset: 0x110  Time Stamp Counter Second Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |SEC       |Time Stamp Counter Second
     * |        |          |This register reflects the bit [63:32] value of 64-bit reference timing counter
     * |        |          |This 32-bit value is used as the second part of time stamp when TSEN (EMAC_TSCTL[0]) is high.
     * @var EMAC_T::TSSUBSEC
     * Offset: 0x114  Time Stamp Counter Sub Second Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |SUBSEC    |Time Stamp Counter Sub-second
     * |        |          |This register reflects the bit [31:0] value of 64-bit reference timing counter
     * |        |          |This 32-bit value is used as the sub-second part of time stamp when TSEN (EMAC_TSCTL[0]) is high.
     * @var EMAC_T::TSINC
     * Offset: 0x118  Time Stamp Increment Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[7:0]   |CNTINC    |Time Stamp Counter Increment
     * |        |          |Time stamp counter increment value.
     * |        |          |If TSEN (EMAC_TSCTL[0]) is high, EMAC adds EMAC_TSSUBSEC with this 8-bit value every
     * |        |          |time when it wants to increase the EMAC_TSSUBSEC value.
     * @var EMAC_T::TSADDEND
     * Offset: 0x11C  Time Stamp Addend Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |ADDEND    |Time Stamp Counter Addend
     * |        |          |This register keeps a 32-bit value for accumulator to enable increment of EMAC_TSSUBSEC.
     * |        |          |If TSEN (EMAC_TSCTL[0]) and TSMODE (EMAC_TSCTL[2]) are both high, EMAC increases accumulator
     * |        |          |with this 32-bit value in each HCLK
     * |        |          |Once the accumulator is overflow, it generates a enable to increase EMAC_TSSUBSEC with an 8-bit
     * |        |          |value kept in register EMAC_TSINC.
     * @var EMAC_T::UPDSEC
     * Offset: 0x120  Time Stamp Update Second Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |SEC       |Time Stamp Counter Second Update
     * |        |          |When TSIEN (EMAC_TSCTL[1]) is high
     * |        |          |EMAC loads this 32-bit value to EMAC_TSSEC directly
     * |        |          |When TSUPDATE (EMAC_TSCTL[3]) is high, EMAC increases EMAC_TSSEC with this 32-bit value.
     * @var EMAC_T::UPDSUBSEC
     * Offset: 0x124  Time Stamp Update Sub Second Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |SUBSEC    |Time Stamp Counter Sub-second Update
     * |        |          |When TSIEN (EMAC_TSCTL[1]) is high
     * |        |          |EMAC loads this 32-bit value to EMAC_TSSUBSEC directly
     * |        |          |When TSUPDATE (EMAC_TSCTL[3]) is high, EMAC increases EMAC_TSSUBSEC with this 32-bit value.
     * @var EMAC_T::ALMSEC
     * Offset: 0x128  Time Stamp Alarm Second Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |SEC       |Time Stamp Counter Second Alarm
     * |        |          |Time stamp counter second part alarm value.
     * |        |          |This value is only useful when ALMEN (EMAC_TSCTL[5]) high
     * |        |          |If ALMEN (EMAC_TSCTL[5]) is high, EMAC_TSSEC equals to EMAC_ALMSEC and EMAC_TSSUBSEC equals to
     * |        |          |EMAC_ALMSUBSEC, Ethernet MAC controller set TSALMIF (EMAC_INTSTS[28]) high.
     * @var EMAC_T::ALMSUBSEC
     * Offset: 0x12C  Time Stamp Alarm Sub Second Register
     * ---------------------------------------------------------------------------------------------------
     * |Bits    |Field     |Descriptions
     * | :----: | :----:   | :---- |
     * |[31:0]  |SUBSEC    |Time Stamp Counter Sub-second Alarm
     * |        |          |Time stamp counter sub-second part alarm value.
     * |        |          |This value is only useful when ALMEN (EMAC_TSCTL[5]) high
     * |        |          |If ALMEN (EMAC_TSCTL[5]) is high, EMAC_TSSEC equals to EMAC_ALMSEC and EMAC_TSSUBSEC equals to
     * |        |          |EMAC_ALMSUBSEC, Ethernet MAC controller set TSALMIF (EMAC_INTSTS[28]) high.
     */
    __IO uint32_t CAMCTL;                /*!< [0x0000] CAM Comparison Control Register                                  */
    __IO uint32_t CAMEN;                 /*!< [0x0004] CAM Enable Register                                              */
    __IO uint32_t CAM0M;                 /*!< [0x0008] CAM0 Most Significant Word Register                              */
    __IO uint32_t CAM0L;                 /*!< [0x000c] CAM0 Least Significant Word Register                             */
    __IO uint32_t CAM1M;                 /*!< [0x0010] CAM1 Most Significant Word Register                              */
    __IO uint32_t CAM1L;                 /*!< [0x0014] CAM1 Least Significant Word Register                             */
    __IO uint32_t CAM2M;                 /*!< [0x0018] CAM2 Most Significant Word Register                              */
    __IO uint32_t CAM2L;                 /*!< [0x001c] CAM2 Least Significant Word Register                             */
    __IO uint32_t CAM3M;                 /*!< [0x0020] CAM3 Most Significant Word Register                              */
    __IO uint32_t CAM3L;                 /*!< [0x0024] CAM3 Least Significant Word Register                             */
    __IO uint32_t CAM4M;                 /*!< [0x0028] CAM4 Most Significant Word Register                              */
    __IO uint32_t CAM4L;                 /*!< [0x002c] CAM4 Least Significant Word Register                             */
    __IO uint32_t CAM5M;                 /*!< [0x0030] CAM5 Most Significant Word Register                              */
    __IO uint32_t CAM5L;                 /*!< [0x0034] CAM5 Least Significant Word Register                             */
    __IO uint32_t CAM6M;                 /*!< [0x0038] CAM6 Most Significant Word Register                              */
    __IO uint32_t CAM6L;                 /*!< [0x003c] CAM6 Least Significant Word Register                             */
    __IO uint32_t CAM7M;                 /*!< [0x0040] CAM7 Most Significant Word Register                              */
    __IO uint32_t CAM7L;                 /*!< [0x0044] CAM7 Least Significant Word Register                             */
    __IO uint32_t CAM8M;                 /*!< [0x0048] CAM8 Most Significant Word Register                              */
    __IO uint32_t CAM8L;                 /*!< [0x004c] CAM8 Least Significant Word Register                             */
    __IO uint32_t CAM9M;                 /*!< [0x0050] CAM9 Most Significant Word Register                              */
    __IO uint32_t CAM9L;                 /*!< [0x0054] CAM9 Least Significant Word Register                             */
    __IO uint32_t CAM10M;                /*!< [0x0058] CAM10 Most Significant Word Register                             */
    __IO uint32_t CAM10L;                /*!< [0x005c] CAM10 Least Significant Word Register                            */
    __IO uint32_t CAM11M;                /*!< [0x0060] CAM11 Most Significant Word Register                             */
    __IO uint32_t CAM11L;                /*!< [0x0064] CAM11 Least Significant Word Register                            */
    __IO uint32_t CAM12M;                /*!< [0x0068] CAM12 Most Significant Word Register                             */
    __IO uint32_t CAM12L;                /*!< [0x006c] CAM12 Least Significant Word Register                            */
    __IO uint32_t CAM13M;                /*!< [0x0070] CAM13 Most Significant Word Register                             */
    __IO uint32_t CAM13L;                /*!< [0x0074] CAM13 Least Significant Word Register                            */
    __IO uint32_t CAM14M;                /*!< [0x0078] CAM14 Most Significant Word Register                             */
    __IO uint32_t CAM14L;                /*!< [0x007c] CAM14 Least Significant Word Register                            */
    __IO uint32_t CAM15MSB;              /*!< [0x0080] CAM15 Most Significant Word Register                             */
    __IO uint32_t CAM15LSB;              /*!< [0x0084] CAM15 Least Significant Word Register                            */
    __IO uint32_t TXDSA;                 /*!< [0x0088] Transmit Descriptor Link List Start Address Register             */
    __IO uint32_t RXDSA;                 /*!< [0x008c] Receive Descriptor Link List Start Address Register              */
    __IO uint32_t CTL;                   /*!< [0x0090] MAC Control Register                                             */
    __IO uint32_t MIIMDAT;               /*!< [0x0094] MII Management Data Register                                     */
    __IO uint32_t MIIMCTL;               /*!< [0x0098] MII Management Control and Address Register                      */
    __IO uint32_t FIFOCTL;               /*!< [0x009c] FIFO Threshold Control Register                                  */
    __O  uint32_t TXST;                  /*!< [0x00a0] Transmit Start Demand Register                                   */
    __O  uint32_t RXST;                  /*!< [0x00a4] Receive Start Demand Register                                    */
    __IO uint32_t MRFL;                  /*!< [0x00a8] Maximum Receive Frame Control Register                           */
    __IO uint32_t INTEN;                 /*!< [0x00ac] MAC Interrupt Enable Register                                    */
    __IO uint32_t INTSTS;                /*!< [0x00b0] MAC Interrupt Status Register                                    */
    __IO uint32_t GENSTS;                /*!< [0x00b4] MAC General Status Register                                      */
    __IO uint32_t MPCNT;                 /*!< [0x00b8] Missed Packet Count Register                                     */
    __I  uint32_t RPCNT;                 /*!< [0x00bc] MAC Receive Pause Count Register                                 */
    /** @cond HIDDEN_SYMBOLS */
    __I  uint32_t RESERVE0[2];
    /** @endcond */
    __IO uint32_t FRSTS;                 /*!< [0x00c8] DMA Receive Frame Status Register                                */
    __I  uint32_t CTXDSA;                /*!< [0x00cc] Current Transmit Descriptor Start Address Register               */
    __I  uint32_t CTXBSA;                /*!< [0x00d0] Current Transmit Buffer Start Address Register                   */
    __I  uint32_t CRXDSA;                /*!< [0x00d4] Current Receive Descriptor Start Address Register                */
    __I  uint32_t CRXBSA;                /*!< [0x00d8] Current Receive Buffer Start Address Register                    */
    /** @cond HIDDEN_SYMBOLS */
    __I  uint32_t RESERVE1[9];
    /** @endcond */
    __IO uint32_t TSCTL;                 /*!< [0x0100] Time Stamp Control Register                                      */
    /** @cond HIDDEN_SYMBOLS */
    __I  uint32_t RESERVE2[3];
    /** @endcond */
    __I  uint32_t TSSEC;                 /*!< [0x0110] Time Stamp Counter Second Register                               */
    __I  uint32_t TSSUBSEC;              /*!< [0x0114] Time Stamp Counter Sub Second Register                           */
    __IO uint32_t TSINC;                 /*!< [0x0118] Time Stamp Increment Register                                    */
    __IO uint32_t TSADDEND;              /*!< [0x011c] Time Stamp Addend Register                                       */
    __IO uint32_t UPDSEC;                /*!< [0x0120] Time Stamp Update Second Register                                */
    __IO uint32_t UPDSUBSEC;             /*!< [0x0124] Time Stamp Update Sub Second Register                            */
    __IO uint32_t ALMSEC;                /*!< [0x0128] Time Stamp Alarm Second Register                                 */
    __IO uint32_t ALMSUBSEC;             /*!< [0x012c] Time Stamp Alarm Sub Second Register                             */

} EMAC_T;

/**
    @addtogroup EMAC_CONST EMAC Bit Field Definition
    Constant Definitions for EMAC Controller
@{ */

#define EMAC_CAMCTL_AUP_Pos              (0)                                               /*!< EMAC_T::CAMCTL: AUP Position           */
#define EMAC_CAMCTL_AUP_Msk              (0x1ul << EMAC_CAMCTL_AUP_Pos)                    /*!< EMAC_T::CAMCTL: AUP Mask               */

#define EMAC_CAMCTL_AMP_Pos              (1)                                               /*!< EMAC_T::CAMCTL: AMP Position           */
#define EMAC_CAMCTL_AMP_Msk              (0x1ul << EMAC_CAMCTL_AMP_Pos)                    /*!< EMAC_T::CAMCTL: AMP Mask               */

#define EMAC_CAMCTL_ABP_Pos              (2)                                               /*!< EMAC_T::CAMCTL: ABP Position           */
#define EMAC_CAMCTL_ABP_Msk              (0x1ul << EMAC_CAMCTL_ABP_Pos)                    /*!< EMAC_T::CAMCTL: ABP Mask               */

#define EMAC_CAMCTL_COMPEN_Pos           (3)                                               /*!< EMAC_T::CAMCTL: COMPEN Position        */
#define EMAC_CAMCTL_COMPEN_Msk           (0x1ul << EMAC_CAMCTL_COMPEN_Pos)                 /*!< EMAC_T::CAMCTL: COMPEN Mask            */

#define EMAC_CAMCTL_CMPEN_Pos            (4)                                               /*!< EMAC_T::CAMCTL: CMPEN Position         */
#define EMAC_CAMCTL_CMPEN_Msk            (0x1ul << EMAC_CAMCTL_CMPEN_Pos)                  /*!< EMAC_T::CAMCTL: CMPEN Mask             */

#define EMAC_CAMEN_CAMxEN_Pos            (0)                                               /*!< EMAC_T::CAMEN: CAMxEN Position         */
#define EMAC_CAMEN_CAMxEN_Msk            (0x1ul << EMAC_CAMEN_CAMxEN_Pos)                  /*!< EMAC_T::CAMEN: CAMxEN Mask             */

#define EMAC_CAM0M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM0M: MACADDR2 Position       */
#define EMAC_CAM0M_MACADDR2_Msk          (0xfful << EMAC_CAM0M_MACADDR2_Pos)               /*!< EMAC_T::CAM0M: MACADDR2 Mask           */

#define EMAC_CAM0M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM0M: MACADDR3 Position       */
#define EMAC_CAM0M_MACADDR3_Msk          (0xfful << EMAC_CAM0M_MACADDR3_Pos)               /*!< EMAC_T::CAM0M: MACADDR3 Mask           */

#define EMAC_CAM0M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM0M: MACADDR4 Position       */
#define EMAC_CAM0M_MACADDR4_Msk          (0xfful << EMAC_CAM0M_MACADDR4_Pos)               /*!< EMAC_T::CAM0M: MACADDR4 Mask           */

#define EMAC_CAM0M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM0M: MACADDR5 Position       */
#define EMAC_CAM0M_MACADDR5_Msk          (0xfful << EMAC_CAM0M_MACADDR5_Pos)               /*!< EMAC_T::CAM0M: MACADDR5 Mask           */

#define EMAC_CAM0L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM0L: MACADDR0 Position       */
#define EMAC_CAM0L_MACADDR0_Msk          (0xfful << EMAC_CAM0L_MACADDR0_Pos)               /*!< EMAC_T::CAM0L: MACADDR0 Mask           */

#define EMAC_CAM0L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM0L: MACADDR1 Position       */
#define EMAC_CAM0L_MACADDR1_Msk          (0xfful << EMAC_CAM0L_MACADDR1_Pos)               /*!< EMAC_T::CAM0L: MACADDR1 Mask           */

#define EMAC_CAM1M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM1M: MACADDR2 Position       */
#define EMAC_CAM1M_MACADDR2_Msk          (0xfful << EMAC_CAM1M_MACADDR2_Pos)               /*!< EMAC_T::CAM1M: MACADDR2 Mask           */

#define EMAC_CAM1M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM1M: MACADDR3 Position       */
#define EMAC_CAM1M_MACADDR3_Msk          (0xfful << EMAC_CAM1M_MACADDR3_Pos)               /*!< EMAC_T::CAM1M: MACADDR3 Mask           */

#define EMAC_CAM1M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM1M: MACADDR4 Position       */
#define EMAC_CAM1M_MACADDR4_Msk          (0xfful << EMAC_CAM1M_MACADDR4_Pos)               /*!< EMAC_T::CAM1M: MACADDR4 Mask           */

#define EMAC_CAM1M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM1M: MACADDR5 Position       */
#define EMAC_CAM1M_MACADDR5_Msk          (0xfful << EMAC_CAM1M_MACADDR5_Pos)               /*!< EMAC_T::CAM1M: MACADDR5 Mask           */

#define EMAC_CAM1L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM1L: MACADDR0 Position       */
#define EMAC_CAM1L_MACADDR0_Msk          (0xfful << EMAC_CAM1L_MACADDR0_Pos)               /*!< EMAC_T::CAM1L: MACADDR0 Mask           */

#define EMAC_CAM1L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM1L: MACADDR1 Position       */
#define EMAC_CAM1L_MACADDR1_Msk          (0xfful << EMAC_CAM1L_MACADDR1_Pos)               /*!< EMAC_T::CAM1L: MACADDR1 Mask           */

#define EMAC_CAM2M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM2M: MACADDR2 Position       */
#define EMAC_CAM2M_MACADDR2_Msk          (0xfful << EMAC_CAM2M_MACADDR2_Pos)               /*!< EMAC_T::CAM2M: MACADDR2 Mask           */

#define EMAC_CAM2M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM2M: MACADDR3 Position       */
#define EMAC_CAM2M_MACADDR3_Msk          (0xfful << EMAC_CAM2M_MACADDR3_Pos)               /*!< EMAC_T::CAM2M: MACADDR3 Mask           */

#define EMAC_CAM2M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM2M: MACADDR4 Position       */
#define EMAC_CAM2M_MACADDR4_Msk          (0xfful << EMAC_CAM2M_MACADDR4_Pos)               /*!< EMAC_T::CAM2M: MACADDR4 Mask           */

#define EMAC_CAM2M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM2M: MACADDR5 Position       */
#define EMAC_CAM2M_MACADDR5_Msk          (0xfful << EMAC_CAM2M_MACADDR5_Pos)               /*!< EMAC_T::CAM2M: MACADDR5 Mask           */

#define EMAC_CAM2L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM2L: MACADDR0 Position       */
#define EMAC_CAM2L_MACADDR0_Msk          (0xfful << EMAC_CAM2L_MACADDR0_Pos)               /*!< EMAC_T::CAM2L: MACADDR0 Mask           */

#define EMAC_CAM2L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM2L: MACADDR1 Position       */
#define EMAC_CAM2L_MACADDR1_Msk          (0xfful << EMAC_CAM2L_MACADDR1_Pos)               /*!< EMAC_T::CAM2L: MACADDR1 Mask           */

#define EMAC_CAM3M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM3M: MACADDR2 Position       */
#define EMAC_CAM3M_MACADDR2_Msk          (0xfful << EMAC_CAM3M_MACADDR2_Pos)               /*!< EMAC_T::CAM3M: MACADDR2 Mask           */

#define EMAC_CAM3M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM3M: MACADDR3 Position       */
#define EMAC_CAM3M_MACADDR3_Msk          (0xfful << EMAC_CAM3M_MACADDR3_Pos)               /*!< EMAC_T::CAM3M: MACADDR3 Mask           */

#define EMAC_CAM3M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM3M: MACADDR4 Position       */
#define EMAC_CAM3M_MACADDR4_Msk          (0xfful << EMAC_CAM3M_MACADDR4_Pos)               /*!< EMAC_T::CAM3M: MACADDR4 Mask           */

#define EMAC_CAM3M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM3M: MACADDR5 Position       */
#define EMAC_CAM3M_MACADDR5_Msk          (0xfful << EMAC_CAM3M_MACADDR5_Pos)               /*!< EMAC_T::CAM3M: MACADDR5 Mask           */

#define EMAC_CAM3L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM3L: MACADDR0 Position       */
#define EMAC_CAM3L_MACADDR0_Msk          (0xfful << EMAC_CAM3L_MACADDR0_Pos)               /*!< EMAC_T::CAM3L: MACADDR0 Mask           */

#define EMAC_CAM3L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM3L: MACADDR1 Position       */
#define EMAC_CAM3L_MACADDR1_Msk          (0xfful << EMAC_CAM3L_MACADDR1_Pos)               /*!< EMAC_T::CAM3L: MACADDR1 Mask           */

#define EMAC_CAM4M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM4M: MACADDR2 Position       */
#define EMAC_CAM4M_MACADDR2_Msk          (0xfful << EMAC_CAM4M_MACADDR2_Pos)               /*!< EMAC_T::CAM4M: MACADDR2 Mask           */

#define EMAC_CAM4M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM4M: MACADDR3 Position       */
#define EMAC_CAM4M_MACADDR3_Msk          (0xfful << EMAC_CAM4M_MACADDR3_Pos)               /*!< EMAC_T::CAM4M: MACADDR3 Mask           */

#define EMAC_CAM4M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM4M: MACADDR4 Position       */
#define EMAC_CAM4M_MACADDR4_Msk          (0xfful << EMAC_CAM4M_MACADDR4_Pos)               /*!< EMAC_T::CAM4M: MACADDR4 Mask           */

#define EMAC_CAM4M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM4M: MACADDR5 Position       */
#define EMAC_CAM4M_MACADDR5_Msk          (0xfful << EMAC_CAM4M_MACADDR5_Pos)               /*!< EMAC_T::CAM4M: MACADDR5 Mask           */

#define EMAC_CAM4L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM4L: MACADDR0 Position       */
#define EMAC_CAM4L_MACADDR0_Msk          (0xfful << EMAC_CAM4L_MACADDR0_Pos)               /*!< EMAC_T::CAM4L: MACADDR0 Mask           */

#define EMAC_CAM4L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM4L: MACADDR1 Position       */
#define EMAC_CAM4L_MACADDR1_Msk          (0xfful << EMAC_CAM4L_MACADDR1_Pos)               /*!< EMAC_T::CAM4L: MACADDR1 Mask           */

#define EMAC_CAM5M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM5M: MACADDR2 Position       */
#define EMAC_CAM5M_MACADDR2_Msk          (0xfful << EMAC_CAM5M_MACADDR2_Pos)               /*!< EMAC_T::CAM5M: MACADDR2 Mask           */

#define EMAC_CAM5M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM5M: MACADDR3 Position       */
#define EMAC_CAM5M_MACADDR3_Msk          (0xfful << EMAC_CAM5M_MACADDR3_Pos)               /*!< EMAC_T::CAM5M: MACADDR3 Mask           */

#define EMAC_CAM5M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM5M: MACADDR4 Position       */
#define EMAC_CAM5M_MACADDR4_Msk          (0xfful << EMAC_CAM5M_MACADDR4_Pos)               /*!< EMAC_T::CAM5M: MACADDR4 Mask           */

#define EMAC_CAM5M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM5M: MACADDR5 Position       */
#define EMAC_CAM5M_MACADDR5_Msk          (0xfful << EMAC_CAM5M_MACADDR5_Pos)               /*!< EMAC_T::CAM5M: MACADDR5 Mask           */

#define EMAC_CAM5L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM5L: MACADDR0 Position       */
#define EMAC_CAM5L_MACADDR0_Msk          (0xfful << EMAC_CAM5L_MACADDR0_Pos)               /*!< EMAC_T::CAM5L: MACADDR0 Mask           */

#define EMAC_CAM5L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM5L: MACADDR1 Position       */
#define EMAC_CAM5L_MACADDR1_Msk          (0xfful << EMAC_CAM5L_MACADDR1_Pos)               /*!< EMAC_T::CAM5L: MACADDR1 Mask           */

#define EMAC_CAM6M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM6M: MACADDR2 Position       */
#define EMAC_CAM6M_MACADDR2_Msk          (0xfful << EMAC_CAM6M_MACADDR2_Pos)               /*!< EMAC_T::CAM6M: MACADDR2 Mask           */

#define EMAC_CAM6M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM6M: MACADDR3 Position       */
#define EMAC_CAM6M_MACADDR3_Msk          (0xfful << EMAC_CAM6M_MACADDR3_Pos)               /*!< EMAC_T::CAM6M: MACADDR3 Mask           */

#define EMAC_CAM6M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM6M: MACADDR4 Position       */
#define EMAC_CAM6M_MACADDR4_Msk          (0xfful << EMAC_CAM6M_MACADDR4_Pos)               /*!< EMAC_T::CAM6M: MACADDR4 Mask           */

#define EMAC_CAM6M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM6M: MACADDR5 Position       */
#define EMAC_CAM6M_MACADDR5_Msk          (0xfful << EMAC_CAM6M_MACADDR5_Pos)               /*!< EMAC_T::CAM6M: MACADDR5 Mask           */

#define EMAC_CAM6L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM6L: MACADDR0 Position       */
#define EMAC_CAM6L_MACADDR0_Msk          (0xfful << EMAC_CAM6L_MACADDR0_Pos)               /*!< EMAC_T::CAM6L: MACADDR0 Mask           */

#define EMAC_CAM6L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM6L: MACADDR1 Position       */
#define EMAC_CAM6L_MACADDR1_Msk          (0xfful << EMAC_CAM6L_MACADDR1_Pos)               /*!< EMAC_T::CAM6L: MACADDR1 Mask           */

#define EMAC_CAM7M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM7M: MACADDR2 Position       */
#define EMAC_CAM7M_MACADDR2_Msk          (0xfful << EMAC_CAM7M_MACADDR2_Pos)               /*!< EMAC_T::CAM7M: MACADDR2 Mask           */

#define EMAC_CAM7M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM7M: MACADDR3 Position       */
#define EMAC_CAM7M_MACADDR3_Msk          (0xfful << EMAC_CAM7M_MACADDR3_Pos)               /*!< EMAC_T::CAM7M: MACADDR3 Mask           */

#define EMAC_CAM7M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM7M: MACADDR4 Position       */
#define EMAC_CAM7M_MACADDR4_Msk          (0xfful << EMAC_CAM7M_MACADDR4_Pos)               /*!< EMAC_T::CAM7M: MACADDR4 Mask           */

#define EMAC_CAM7M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM7M: MACADDR5 Position       */
#define EMAC_CAM7M_MACADDR5_Msk          (0xfful << EMAC_CAM7M_MACADDR5_Pos)               /*!< EMAC_T::CAM7M: MACADDR5 Mask           */

#define EMAC_CAM7L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM7L: MACADDR0 Position       */
#define EMAC_CAM7L_MACADDR0_Msk          (0xfful << EMAC_CAM7L_MACADDR0_Pos)               /*!< EMAC_T::CAM7L: MACADDR0 Mask           */

#define EMAC_CAM7L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM7L: MACADDR1 Position       */
#define EMAC_CAM7L_MACADDR1_Msk          (0xfful << EMAC_CAM7L_MACADDR1_Pos)               /*!< EMAC_T::CAM7L: MACADDR1 Mask           */

#define EMAC_CAM8M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM8M: MACADDR2 Position       */
#define EMAC_CAM8M_MACADDR2_Msk          (0xfful << EMAC_CAM8M_MACADDR2_Pos)               /*!< EMAC_T::CAM8M: MACADDR2 Mask           */

#define EMAC_CAM8M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM8M: MACADDR3 Position       */
#define EMAC_CAM8M_MACADDR3_Msk          (0xfful << EMAC_CAM8M_MACADDR3_Pos)               /*!< EMAC_T::CAM8M: MACADDR3 Mask           */

#define EMAC_CAM8M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM8M: MACADDR4 Position       */
#define EMAC_CAM8M_MACADDR4_Msk          (0xfful << EMAC_CAM8M_MACADDR4_Pos)               /*!< EMAC_T::CAM8M: MACADDR4 Mask           */

#define EMAC_CAM8M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM8M: MACADDR5 Position       */
#define EMAC_CAM8M_MACADDR5_Msk          (0xfful << EMAC_CAM8M_MACADDR5_Pos)               /*!< EMAC_T::CAM8M: MACADDR5 Mask           */

#define EMAC_CAM8L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM8L: MACADDR0 Position       */
#define EMAC_CAM8L_MACADDR0_Msk          (0xfful << EMAC_CAM8L_MACADDR0_Pos)               /*!< EMAC_T::CAM8L: MACADDR0 Mask           */

#define EMAC_CAM8L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM8L: MACADDR1 Position       */
#define EMAC_CAM8L_MACADDR1_Msk          (0xfful << EMAC_CAM8L_MACADDR1_Pos)               /*!< EMAC_T::CAM8L: MACADDR1 Mask           */

#define EMAC_CAM9M_MACADDR2_Pos          (0)                                               /*!< EMAC_T::CAM9M: MACADDR2 Position       */
#define EMAC_CAM9M_MACADDR2_Msk          (0xfful << EMAC_CAM9M_MACADDR2_Pos)               /*!< EMAC_T::CAM9M: MACADDR2 Mask           */

#define EMAC_CAM9M_MACADDR3_Pos          (8)                                               /*!< EMAC_T::CAM9M: MACADDR3 Position       */
#define EMAC_CAM9M_MACADDR3_Msk          (0xfful << EMAC_CAM9M_MACADDR3_Pos)               /*!< EMAC_T::CAM9M: MACADDR3 Mask           */

#define EMAC_CAM9M_MACADDR4_Pos          (16)                                              /*!< EMAC_T::CAM9M: MACADDR4 Position       */
#define EMAC_CAM9M_MACADDR4_Msk          (0xfful << EMAC_CAM9M_MACADDR4_Pos)               /*!< EMAC_T::CAM9M: MACADDR4 Mask           */

#define EMAC_CAM9M_MACADDR5_Pos          (24)                                              /*!< EMAC_T::CAM9M: MACADDR5 Position       */
#define EMAC_CAM9M_MACADDR5_Msk          (0xfful << EMAC_CAM9M_MACADDR5_Pos)               /*!< EMAC_T::CAM9M: MACADDR5 Mask           */

#define EMAC_CAM9L_MACADDR0_Pos          (16)                                              /*!< EMAC_T::CAM9L: MACADDR0 Position       */
#define EMAC_CAM9L_MACADDR0_Msk          (0xfful << EMAC_CAM9L_MACADDR0_Pos)               /*!< EMAC_T::CAM9L: MACADDR0 Mask           */

#define EMAC_CAM9L_MACADDR1_Pos          (24)                                              /*!< EMAC_T::CAM9L: MACADDR1 Position       */
#define EMAC_CAM9L_MACADDR1_Msk          (0xfful << EMAC_CAM9L_MACADDR1_Pos)               /*!< EMAC_T::CAM9L: MACADDR1 Mask           */

#define EMAC_CAM10M_MACADDR2_Pos         (0)                                               /*!< EMAC_T::CAM10M: MACADDR2 Position      */
#define EMAC_CAM10M_MACADDR2_Msk         (0xfful << EMAC_CAM10M_MACADDR2_Pos)              /*!< EMAC_T::CAM10M: MACADDR2 Mask          */

#define EMAC_CAM10M_MACADDR3_Pos         (8)                                               /*!< EMAC_T::CAM10M: MACADDR3 Position      */
#define EMAC_CAM10M_MACADDR3_Msk         (0xfful << EMAC_CAM10M_MACADDR3_Pos)              /*!< EMAC_T::CAM10M: MACADDR3 Mask          */

#define EMAC_CAM10M_MACADDR4_Pos         (16)                                              /*!< EMAC_T::CAM10M: MACADDR4 Position      */
#define EMAC_CAM10M_MACADDR4_Msk         (0xfful << EMAC_CAM10M_MACADDR4_Pos)              /*!< EMAC_T::CAM10M: MACADDR4 Mask          */

#define EMAC_CAM10M_MACADDR5_Pos         (24)                                              /*!< EMAC_T::CAM10M: MACADDR5 Position      */
#define EMAC_CAM10M_MACADDR5_Msk         (0xfful << EMAC_CAM10M_MACADDR5_Pos)              /*!< EMAC_T::CAM10M: MACADDR5 Mask          */

#define EMAC_CAM10L_MACADDR0_Pos         (16)                                              /*!< EMAC_T::CAM10L: MACADDR0 Position      */
#define EMAC_CAM10L_MACADDR0_Msk         (0xfful << EMAC_CAM10L_MACADDR0_Pos)              /*!< EMAC_T::CAM10L: MACADDR0 Mask          */

#define EMAC_CAM10L_MACADDR1_Pos         (24)                                              /*!< EMAC_T::CAM10L: MACADDR1 Position      */
#define EMAC_CAM10L_MACADDR1_Msk         (0xfful << EMAC_CAM10L_MACADDR1_Pos)              /*!< EMAC_T::CAM10L: MACADDR1 Mask          */

#define EMAC_CAM11M_MACADDR2_Pos         (0)                                               /*!< EMAC_T::CAM11M: MACADDR2 Position      */
#define EMAC_CAM11M_MACADDR2_Msk         (0xfful << EMAC_CAM11M_MACADDR2_Pos)              /*!< EMAC_T::CAM11M: MACADDR2 Mask          */

#define EMAC_CAM11M_MACADDR3_Pos         (8)                                               /*!< EMAC_T::CAM11M: MACADDR3 Position      */
#define EMAC_CAM11M_MACADDR3_Msk         (0xfful << EMAC_CAM11M_MACADDR3_Pos)              /*!< EMAC_T::CAM11M: MACADDR3 Mask          */

#define EMAC_CAM11M_MACADDR4_Pos         (16)                                              /*!< EMAC_T::CAM11M: MACADDR4 Position      */
#define EMAC_CAM11M_MACADDR4_Msk         (0xfful << EMAC_CAM11M_MACADDR4_Pos)              /*!< EMAC_T::CAM11M: MACADDR4 Mask          */

#define EMAC_CAM11M_MACADDR5_Pos         (24)                                              /*!< EMAC_T::CAM11M: MACADDR5 Position      */
#define EMAC_CAM11M_MACADDR5_Msk         (0xfful << EMAC_CAM11M_MACADDR5_Pos)              /*!< EMAC_T::CAM11M: MACADDR5 Mask          */

#define EMAC_CAM11L_MACADDR0_Pos         (16)                                              /*!< EMAC_T::CAM11L: MACADDR0 Position      */
#define EMAC_CAM11L_MACADDR0_Msk         (0xfful << EMAC_CAM11L_MACADDR0_Pos)              /*!< EMAC_T::CAM11L: MACADDR0 Mask          */

#define EMAC_CAM11L_MACADDR1_Pos         (24)                                              /*!< EMAC_T::CAM11L: MACADDR1 Position      */
#define EMAC_CAM11L_MACADDR1_Msk         (0xfful << EMAC_CAM11L_MACADDR1_Pos)              /*!< EMAC_T::CAM11L: MACADDR1 Mask          */

#define EMAC_CAM12M_MACADDR2_Pos         (0)                                               /*!< EMAC_T::CAM12M: MACADDR2 Position      */
#define EMAC_CAM12M_MACADDR2_Msk         (0xfful << EMAC_CAM12M_MACADDR2_Pos)              /*!< EMAC_T::CAM12M: MACADDR2 Mask          */

#define EMAC_CAM12M_MACADDR3_Pos         (8)                                               /*!< EMAC_T::CAM12M: MACADDR3 Position      */
#define EMAC_CAM12M_MACADDR3_Msk         (0xfful << EMAC_CAM12M_MACADDR3_Pos)              /*!< EMAC_T::CAM12M: MACADDR3 Mask          */

#define EMAC_CAM12M_MACADDR4_Pos         (16)                                              /*!< EMAC_T::CAM12M: MACADDR4 Position      */
#define EMAC_CAM12M_MACADDR4_Msk         (0xfful << EMAC_CAM12M_MACADDR4_Pos)              /*!< EMAC_T::CAM12M: MACADDR4 Mask          */

#define EMAC_CAM12M_MACADDR5_Pos         (24)                                              /*!< EMAC_T::CAM12M: MACADDR5 Position      */
#define EMAC_CAM12M_MACADDR5_Msk         (0xfful << EMAC_CAM12M_MACADDR5_Pos)              /*!< EMAC_T::CAM12M: MACADDR5 Mask          */

#define EMAC_CAM12L_MACADDR0_Pos         (16)                                              /*!< EMAC_T::CAM12L: MACADDR0 Position      */
#define EMAC_CAM12L_MACADDR0_Msk         (0xfful << EMAC_CAM12L_MACADDR0_Pos)              /*!< EMAC_T::CAM12L: MACADDR0 Mask          */

#define EMAC_CAM12L_MACADDR1_Pos         (24)                                              /*!< EMAC_T::CAM12L: MACADDR1 Position      */
#define EMAC_CAM12L_MACADDR1_Msk         (0xfful << EMAC_CAM12L_MACADDR1_Pos)              /*!< EMAC_T::CAM12L: MACADDR1 Mask          */

#define EMAC_CAM13M_MACADDR2_Pos         (0)                                               /*!< EMAC_T::CAM13M: MACADDR2 Position      */
#define EMAC_CAM13M_MACADDR2_Msk         (0xfful << EMAC_CAM13M_MACADDR2_Pos)              /*!< EMAC_T::CAM13M: MACADDR2 Mask          */

#define EMAC_CAM13M_MACADDR3_Pos         (8)                                               /*!< EMAC_T::CAM13M: MACADDR3 Position      */
#define EMAC_CAM13M_MACADDR3_Msk         (0xfful << EMAC_CAM13M_MACADDR3_Pos)              /*!< EMAC_T::CAM13M: MACADDR3 Mask          */

#define EMAC_CAM13M_MACADDR4_Pos         (16)                                              /*!< EMAC_T::CAM13M: MACADDR4 Position      */
#define EMAC_CAM13M_MACADDR4_Msk         (0xfful << EMAC_CAM13M_MACADDR4_Pos)              /*!< EMAC_T::CAM13M: MACADDR4 Mask          */

#define EMAC_CAM13M_MACADDR5_Pos         (24)                                              /*!< EMAC_T::CAM13M: MACADDR5 Position      */
#define EMAC_CAM13M_MACADDR5_Msk         (0xfful << EMAC_CAM13M_MACADDR5_Pos)              /*!< EMAC_T::CAM13M: MACADDR5 Mask          */

#define EMAC_CAM13L_MACADDR0_Pos         (16)                                              /*!< EMAC_T::CAM13L: MACADDR0 Position      */
#define EMAC_CAM13L_MACADDR0_Msk         (0xfful << EMAC_CAM13L_MACADDR0_Pos)              /*!< EMAC_T::CAM13L: MACADDR0 Mask          */

#define EMAC_CAM13L_MACADDR1_Pos         (24)                                              /*!< EMAC_T::CAM13L: MACADDR1 Position      */
#define EMAC_CAM13L_MACADDR1_Msk         (0xfful << EMAC_CAM13L_MACADDR1_Pos)              /*!< EMAC_T::CAM13L: MACADDR1 Mask          */

#define EMAC_CAM14M_MACADDR2_Pos         (0)                                               /*!< EMAC_T::CAM14M: MACADDR2 Position      */
#define EMAC_CAM14M_MACADDR2_Msk         (0xfful << EMAC_CAM14M_MACADDR2_Pos)              /*!< EMAC_T::CAM14M: MACADDR2 Mask          */

#define EMAC_CAM14M_MACADDR3_Pos         (8)                                               /*!< EMAC_T::CAM14M: MACADDR3 Position      */
#define EMAC_CAM14M_MACADDR3_Msk         (0xfful << EMAC_CAM14M_MACADDR3_Pos)              /*!< EMAC_T::CAM14M: MACADDR3 Mask          */

#define EMAC_CAM14M_MACADDR4_Pos         (16)                                              /*!< EMAC_T::CAM14M: MACADDR4 Position      */
#define EMAC_CAM14M_MACADDR4_Msk         (0xfful << EMAC_CAM14M_MACADDR4_Pos)              /*!< EMAC_T::CAM14M: MACADDR4 Mask          */

#define EMAC_CAM14M_MACADDR5_Pos         (24)                                              /*!< EMAC_T::CAM14M: MACADDR5 Position      */
#define EMAC_CAM14M_MACADDR5_Msk         (0xfful << EMAC_CAM14M_MACADDR5_Pos)              /*!< EMAC_T::CAM14M: MACADDR5 Mask          */

#define EMAC_CAM14L_MACADDR0_Pos         (16)                                              /*!< EMAC_T::CAM14L: MACADDR0 Position      */
#define EMAC_CAM14L_MACADDR0_Msk         (0xfful << EMAC_CAM14L_MACADDR0_Pos)              /*!< EMAC_T::CAM14L: MACADDR0 Mask          */

#define EMAC_CAM14L_MACADDR1_Pos         (24)                                              /*!< EMAC_T::CAM14L: MACADDR1 Position      */
#define EMAC_CAM14L_MACADDR1_Msk         (0xfful << EMAC_CAM14L_MACADDR1_Pos)              /*!< EMAC_T::CAM14L: MACADDR1 Mask          */

#define EMAC_CAM15MSB_OPCODE_Pos         (0)                                               /*!< EMAC_T::CAM15MSB: OPCODE Position      */
#define EMAC_CAM15MSB_OPCODE_Msk         (0xfffful << EMAC_CAM15MSB_OPCODE_Pos)            /*!< EMAC_T::CAM15MSB: OPCODE Mask          */

#define EMAC_CAM15MSB_LENGTH_Pos         (16)                                              /*!< EMAC_T::CAM15MSB: LENGTH Position      */
#define EMAC_CAM15MSB_LENGTH_Msk         (0xfffful << EMAC_CAM15MSB_LENGTH_Pos)            /*!< EMAC_T::CAM15MSB: LENGTH Mask          */

#define EMAC_CAM15LSB_OPERAND_Pos        (24)                                              /*!< EMAC_T::CAM15LSB: OPERAND Position     */
#define EMAC_CAM15LSB_OPERAND_Msk        (0xfful << EMAC_CAM15LSB_OPERAND_Pos)             /*!< EMAC_T::CAM15LSB: OPERAND Mask         */

#define EMAC_TXDSA_TXDSA_Pos             (0)                                               /*!< EMAC_T::TXDSA: TXDSA Position          */
#define EMAC_TXDSA_TXDSA_Msk             (0xfffffffful << EMAC_TXDSA_TXDSA_Pos)            /*!< EMAC_T::TXDSA: TXDSA Mask              */

#define EMAC_RXDSA_RXDSA_Pos             (0)                                               /*!< EMAC_T::RXDSA: RXDSA Position          */
#define EMAC_RXDSA_RXDSA_Msk             (0xfffffffful << EMAC_RXDSA_RXDSA_Pos)            /*!< EMAC_T::RXDSA: RXDSA Mask              */

#define EMAC_CTL_RXON_Pos                (0)                                               /*!< EMAC_T::CTL: RXON Position             */
#define EMAC_CTL_RXON_Msk                (0x1ul << EMAC_CTL_RXON_Pos)                      /*!< EMAC_T::CTL: RXON Mask                 */

#define EMAC_CTL_ALP_Pos                 (1)                                               /*!< EMAC_T::CTL: ALP Position              */
#define EMAC_CTL_ALP_Msk                 (0x1ul << EMAC_CTL_ALP_Pos)                       /*!< EMAC_T::CTL: ALP Mask                  */

#define EMAC_CTL_ARP_Pos                 (2)                                               /*!< EMAC_T::CTL: ARP Position              */
#define EMAC_CTL_ARP_Msk                 (0x1ul << EMAC_CTL_ARP_Pos)                       /*!< EMAC_T::CTL: ARP Mask                  */

#define EMAC_CTL_ACP_Pos                 (3)                                               /*!< EMAC_T::CTL: ACP Position              */
#define EMAC_CTL_ACP_Msk                 (0x1ul << EMAC_CTL_ACP_Pos)                       /*!< EMAC_T::CTL: ACP Mask                  */

#define EMAC_CTL_AEP_Pos                 (4)                                               /*!< EMAC_T::CTL: AEP Position              */
#define EMAC_CTL_AEP_Msk                 (0x1ul << EMAC_CTL_AEP_Pos)                       /*!< EMAC_T::CTL: AEP Mask                  */

#define EMAC_CTL_STRIPCRC_Pos            (5)                                               /*!< EMAC_T::CTL: STRIPCRC Position         */
#define EMAC_CTL_STRIPCRC_Msk            (0x1ul << EMAC_CTL_STRIPCRC_Pos)                  /*!< EMAC_T::CTL: STRIPCRC Mask             */

#define EMAC_CTL_WOLEN_Pos               (6)                                               /*!< EMAC_T::CTL: WOLEN Position            */
#define EMAC_CTL_WOLEN_Msk               (0x1ul << EMAC_CTL_WOLEN_Pos)                     /*!< EMAC_T::CTL: WOLEN Mask                */

#define EMAC_CTL_TXON_Pos                (8)                                               /*!< EMAC_T::CTL: TXON Position             */
#define EMAC_CTL_TXON_Msk                (0x1ul << EMAC_CTL_TXON_Pos)                      /*!< EMAC_T::CTL: TXON Mask                 */

#define EMAC_CTL_NODEF_Pos               (9)                                               /*!< EMAC_T::CTL: NODEF Position            */
#define EMAC_CTL_NODEF_Msk               (0x1ul << EMAC_CTL_NODEF_Pos)                     /*!< EMAC_T::CTL: NODEF Mask                */

#define EMAC_CTL_SDPZ_Pos                (16)                                              /*!< EMAC_T::CTL: SDPZ Position             */
#define EMAC_CTL_SDPZ_Msk                (0x1ul << EMAC_CTL_SDPZ_Pos)                      /*!< EMAC_T::CTL: SDPZ Mask                 */

#define EMAC_CTL_SQECHKEN_Pos            (17)                                              /*!< EMAC_T::CTL: SQECHKEN Position         */
#define EMAC_CTL_SQECHKEN_Msk            (0x1ul << EMAC_CTL_SQECHKEN_Pos)                  /*!< EMAC_T::CTL: SQECHKEN Mask             */

#define EMAC_CTL_FUDUP_Pos               (18)                                              /*!< EMAC_T::CTL: FUDUP Position            */
#define EMAC_CTL_FUDUP_Msk               (0x1ul << EMAC_CTL_FUDUP_Pos)                     /*!< EMAC_T::CTL: FUDUP Mask                */

#define EMAC_CTL_RMIIRXCTL_Pos           (19)                                              /*!< EMAC_T::CTL: RMIIRXCTL Position        */
#define EMAC_CTL_RMIIRXCTL_Msk           (0x1ul << EMAC_CTL_RMIIRXCTL_Pos)                 /*!< EMAC_T::CTL: RMIIRXCTL Mask            */

#define EMAC_CTL_OPMODE_Pos              (20)                                              /*!< EMAC_T::CTL: OPMODE Position           */
#define EMAC_CTL_OPMODE_Msk              (0x1ul << EMAC_CTL_OPMODE_Pos)                    /*!< EMAC_T::CTL: OPMODE Mask               */

#define EMAC_CTL_RMIIEN_Pos              (22)                                              /*!< EMAC_T::CTL: RMIIEN Position           */
#define EMAC_CTL_RMIIEN_Msk              (0x1ul << EMAC_CTL_RMIIEN_Pos)                    /*!< EMAC_T::CTL: RMIIEN Mask               */

#define EMAC_CTL_RST_Pos                 (24)                                              /*!< EMAC_T::CTL: RST Position              */
#define EMAC_CTL_RST_Msk                 (0x1ul << EMAC_CTL_RST_Pos)                       /*!< EMAC_T::CTL: RST Mask                  */

#define EMAC_MIIMDAT_DATA_Pos            (0)                                               /*!< EMAC_T::MIIMDAT: DATA Position         */
#define EMAC_MIIMDAT_DATA_Msk            (0xfffful << EMAC_MIIMDAT_DATA_Pos)               /*!< EMAC_T::MIIMDAT: DATA Mask             */

#define EMAC_MIIMCTL_PHYREG_Pos          (0)                                               /*!< EMAC_T::MIIMCTL: PHYREG Position       */
#define EMAC_MIIMCTL_PHYREG_Msk          (0x1ful << EMAC_MIIMCTL_PHYREG_Pos)               /*!< EMAC_T::MIIMCTL: PHYREG Mask           */

#define EMAC_MIIMCTL_PHYADDR_Pos         (8)                                               /*!< EMAC_T::MIIMCTL: PHYADDR Position      */
#define EMAC_MIIMCTL_PHYADDR_Msk         (0x1ful << EMAC_MIIMCTL_PHYADDR_Pos)              /*!< EMAC_T::MIIMCTL: PHYADDR Mask          */

#define EMAC_MIIMCTL_WRITE_Pos           (16)                                              /*!< EMAC_T::MIIMCTL: WRITE Position        */
#define EMAC_MIIMCTL_WRITE_Msk           (0x1ul << EMAC_MIIMCTL_WRITE_Pos)                 /*!< EMAC_T::MIIMCTL: WRITE Mask            */

#define EMAC_MIIMCTL_BUSY_Pos            (17)                                              /*!< EMAC_T::MIIMCTL: BUSY Position         */
#define EMAC_MIIMCTL_BUSY_Msk            (0x1ul << EMAC_MIIMCTL_BUSY_Pos)                  /*!< EMAC_T::MIIMCTL: BUSY Mask             */

#define EMAC_MIIMCTL_PREAMSP_Pos         (18)                                              /*!< EMAC_T::MIIMCTL: PREAMSP Position      */
#define EMAC_MIIMCTL_PREAMSP_Msk         (0x1ul << EMAC_MIIMCTL_PREAMSP_Pos)               /*!< EMAC_T::MIIMCTL: PREAMSP Mask          */

#define EMAC_MIIMCTL_MDCON_Pos           (19)                                              /*!< EMAC_T::MIIMCTL: MDCON Position        */
#define EMAC_MIIMCTL_MDCON_Msk           (0x1ul << EMAC_MIIMCTL_MDCON_Pos)                 /*!< EMAC_T::MIIMCTL: MDCON Mask            */

#define EMAC_FIFOCTL_RXFIFOTH_Pos        (0)                                               /*!< EMAC_T::FIFOCTL: RXFIFOTH Position     */
#define EMAC_FIFOCTL_RXFIFOTH_Msk        (0x3ul << EMAC_FIFOCTL_RXFIFOTH_Pos)              /*!< EMAC_T::FIFOCTL: RXFIFOTH Mask         */

#define EMAC_FIFOCTL_TXFIFOTH_Pos        (8)                                               /*!< EMAC_T::FIFOCTL: TXFIFOTH Position     */
#define EMAC_FIFOCTL_TXFIFOTH_Msk        (0x3ul << EMAC_FIFOCTL_TXFIFOTH_Pos)              /*!< EMAC_T::FIFOCTL: TXFIFOTH Mask         */

#define EMAC_FIFOCTL_BURSTLEN_Pos        (20)                                              /*!< EMAC_T::FIFOCTL: BURSTLEN Position     */
#define EMAC_FIFOCTL_BURSTLEN_Msk        (0x3ul << EMAC_FIFOCTL_BURSTLEN_Pos)              /*!< EMAC_T::FIFOCTL: BURSTLEN Mask         */

#define EMAC_TXST_TXST_Pos               (0)                                               /*!< EMAC_T::TXST: TXST Position            */
#define EMAC_TXST_TXST_Msk               (0xfffffffful << EMAC_TXST_TXST_Pos)              /*!< EMAC_T::TXST: TXST Mask                */

#define EMAC_RXST_RXST_Pos               (0)                                               /*!< EMAC_T::RXST: RXST Position            */
#define EMAC_RXST_RXST_Msk               (0xfffffffful << EMAC_RXST_RXST_Pos)              /*!< EMAC_T::RXST: RXST Mask                */

#define EMAC_MRFL_MRFL_Pos               (0)                                               /*!< EMAC_T::MRFL: MRFL Position            */
#define EMAC_MRFL_MRFL_Msk               (0xfffful << EMAC_MRFL_MRFL_Pos)                  /*!< EMAC_T::MRFL: MRFL Mask                */

#define EMAC_INTEN_RXIEN_Pos             (0)                                               /*!< EMAC_T::INTEN: RXIEN Position          */
#define EMAC_INTEN_RXIEN_Msk             (0x1ul << EMAC_INTEN_RXIEN_Pos)                   /*!< EMAC_T::INTEN: RXIEN Mask              */

#define EMAC_INTEN_CRCEIEN_Pos           (1)                                               /*!< EMAC_T::INTEN: CRCEIEN Position        */
#define EMAC_INTEN_CRCEIEN_Msk           (0x1ul << EMAC_INTEN_CRCEIEN_Pos)                 /*!< EMAC_T::INTEN: CRCEIEN Mask            */

#define EMAC_INTEN_RXOVIEN_Pos           (2)                                               /*!< EMAC_T::INTEN: RXOVIEN Position        */
#define EMAC_INTEN_RXOVIEN_Msk           (0x1ul << EMAC_INTEN_RXOVIEN_Pos)                 /*!< EMAC_T::INTEN: RXOVIEN Mask            */

#define EMAC_INTEN_LPIEN_Pos             (3)                                               /*!< EMAC_T::INTEN: LPIEN Position          */
#define EMAC_INTEN_LPIEN_Msk             (0x1ul << EMAC_INTEN_LPIEN_Pos)                   /*!< EMAC_T::INTEN: LPIEN Mask              */

#define EMAC_INTEN_RXGDIEN_Pos           (4)                                               /*!< EMAC_T::INTEN: RXGDIEN Position        */
#define EMAC_INTEN_RXGDIEN_Msk           (0x1ul << EMAC_INTEN_RXGDIEN_Pos)                 /*!< EMAC_T::INTEN: RXGDIEN Mask            */

#define EMAC_INTEN_ALIEIEN_Pos           (5)                                               /*!< EMAC_T::INTEN: ALIEIEN Position        */
#define EMAC_INTEN_ALIEIEN_Msk           (0x1ul << EMAC_INTEN_ALIEIEN_Pos)                 /*!< EMAC_T::INTEN: ALIEIEN Mask            */

#define EMAC_INTEN_RPIEN_Pos             (6)                                               /*!< EMAC_T::INTEN: RPIEN Position          */
#define EMAC_INTEN_RPIEN_Msk             (0x1ul << EMAC_INTEN_RPIEN_Pos)                   /*!< EMAC_T::INTEN: RPIEN Mask              */

#define EMAC_INTEN_MPCOVIEN_Pos          (7)                                               /*!< EMAC_T::INTEN: MPCOVIEN Position       */
#define EMAC_INTEN_MPCOVIEN_Msk          (0x1ul << EMAC_INTEN_MPCOVIEN_Pos)                /*!< EMAC_T::INTEN: MPCOVIEN Mask           */

#define EMAC_INTEN_MFLEIEN_Pos           (8)                                               /*!< EMAC_T::INTEN: MFLEIEN Position        */
#define EMAC_INTEN_MFLEIEN_Msk           (0x1ul << EMAC_INTEN_MFLEIEN_Pos)                 /*!< EMAC_T::INTEN: MFLEIEN Mask            */

#define EMAC_INTEN_DENIEN_Pos            (9)                                               /*!< EMAC_T::INTEN: DENIEN Position         */
#define EMAC_INTEN_DENIEN_Msk            (0x1ul << EMAC_INTEN_DENIEN_Pos)                  /*!< EMAC_T::INTEN: DENIEN Mask             */

#define EMAC_INTEN_RDUIEN_Pos            (10)                                              /*!< EMAC_T::INTEN: RDUIEN Position         */
#define EMAC_INTEN_RDUIEN_Msk            (0x1ul << EMAC_INTEN_RDUIEN_Pos)                  /*!< EMAC_T::INTEN: RDUIEN Mask             */

#define EMAC_INTEN_RXBEIEN_Pos           (11)                                              /*!< EMAC_T::INTEN: RXBEIEN Position        */
#define EMAC_INTEN_RXBEIEN_Msk           (0x1ul << EMAC_INTEN_RXBEIEN_Pos)                 /*!< EMAC_T::INTEN: RXBEIEN Mask            */

#define EMAC_INTEN_CFRIEN_Pos            (14)                                              /*!< EMAC_T::INTEN: CFRIEN Position         */
#define EMAC_INTEN_CFRIEN_Msk            (0x1ul << EMAC_INTEN_CFRIEN_Pos)                  /*!< EMAC_T::INTEN: CFRIEN Mask             */

#define EMAC_INTEN_WOLIEN_Pos            (15)                                              /*!< EMAC_T::INTEN: WOLIEN Position         */
#define EMAC_INTEN_WOLIEN_Msk            (0x1ul << EMAC_INTEN_WOLIEN_Pos)                  /*!< EMAC_T::INTEN: WOLIEN Mask             */

#define EMAC_INTEN_TXIEN_Pos             (16)                                              /*!< EMAC_T::INTEN: TXIEN Position          */
#define EMAC_INTEN_TXIEN_Msk             (0x1ul << EMAC_INTEN_TXIEN_Pos)                   /*!< EMAC_T::INTEN: TXIEN Mask              */

#define EMAC_INTEN_TXUDIEN_Pos           (17)                                              /*!< EMAC_T::INTEN: TXUDIEN Position        */
#define EMAC_INTEN_TXUDIEN_Msk           (0x1ul << EMAC_INTEN_TXUDIEN_Pos)                 /*!< EMAC_T::INTEN: TXUDIEN Mask            */

#define EMAC_INTEN_TXCPIEN_Pos           (18)                                              /*!< EMAC_T::INTEN: TXCPIEN Position        */
#define EMAC_INTEN_TXCPIEN_Msk           (0x1ul << EMAC_INTEN_TXCPIEN_Pos)                 /*!< EMAC_T::INTEN: TXCPIEN Mask            */

#define EMAC_INTEN_EXDEFIEN_Pos          (19)                                              /*!< EMAC_T::INTEN: EXDEFIEN Position       */
#define EMAC_INTEN_EXDEFIEN_Msk          (0x1ul << EMAC_INTEN_EXDEFIEN_Pos)                /*!< EMAC_T::INTEN: EXDEFIEN Mask           */

#define EMAC_INTEN_NCSIEN_Pos            (20)                                              /*!< EMAC_T::INTEN: NCSIEN Position         */
#define EMAC_INTEN_NCSIEN_Msk            (0x1ul << EMAC_INTEN_NCSIEN_Pos)                  /*!< EMAC_T::INTEN: NCSIEN Mask             */

#define EMAC_INTEN_TXABTIEN_Pos          (21)                                              /*!< EMAC_T::INTEN: TXABTIEN Position       */
#define EMAC_INTEN_TXABTIEN_Msk          (0x1ul << EMAC_INTEN_TXABTIEN_Pos)                /*!< EMAC_T::INTEN: TXABTIEN Mask           */

#define EMAC_INTEN_LCIEN_Pos             (22)                                              /*!< EMAC_T::INTEN: LCIEN Position          */
#define EMAC_INTEN_LCIEN_Msk             (0x1ul << EMAC_INTEN_LCIEN_Pos)                   /*!< EMAC_T::INTEN: LCIEN Mask              */

#define EMAC_INTEN_TDUIEN_Pos            (23)                                              /*!< EMAC_T::INTEN: TDUIEN Position         */
#define EMAC_INTEN_TDUIEN_Msk            (0x1ul << EMAC_INTEN_TDUIEN_Pos)                  /*!< EMAC_T::INTEN: TDUIEN Mask             */

#define EMAC_INTEN_TXBEIEN_Pos           (24)                                              /*!< EMAC_T::INTEN: TXBEIEN Position        */
#define EMAC_INTEN_TXBEIEN_Msk           (0x1ul << EMAC_INTEN_TXBEIEN_Pos)                 /*!< EMAC_T::INTEN: TXBEIEN Mask            */

#define EMAC_INTEN_TSALMIEN_Pos          (28)                                              /*!< EMAC_T::INTEN: TSALMIEN Position       */
#define EMAC_INTEN_TSALMIEN_Msk          (0x1ul << EMAC_INTEN_TSALMIEN_Pos)                /*!< EMAC_T::INTEN: TSALMIEN Mask           */

#define EMAC_INTSTS_RXIF_Pos             (0)                                               /*!< EMAC_T::INTSTS: RXIF Position          */
#define EMAC_INTSTS_RXIF_Msk             (0x1ul << EMAC_INTSTS_RXIF_Pos)                   /*!< EMAC_T::INTSTS: RXIF Mask              */

#define EMAC_INTSTS_CRCEIF_Pos           (1)                                               /*!< EMAC_T::INTSTS: CRCEIF Position        */
#define EMAC_INTSTS_CRCEIF_Msk           (0x1ul << EMAC_INTSTS_CRCEIF_Pos)                 /*!< EMAC_T::INTSTS: CRCEIF Mask            */

#define EMAC_INTSTS_RXOVIF_Pos           (2)                                               /*!< EMAC_T::INTSTS: RXOVIF Position        */
#define EMAC_INTSTS_RXOVIF_Msk           (0x1ul << EMAC_INTSTS_RXOVIF_Pos)                 /*!< EMAC_T::INTSTS: RXOVIF Mask            */

#define EMAC_INTSTS_LPIF_Pos             (3)                                               /*!< EMAC_T::INTSTS: LPIF Position          */
#define EMAC_INTSTS_LPIF_Msk             (0x1ul << EMAC_INTSTS_LPIF_Pos)                   /*!< EMAC_T::INTSTS: LPIF Mask              */

#define EMAC_INTSTS_RXGDIF_Pos           (4)                                               /*!< EMAC_T::INTSTS: RXGDIF Position        */
#define EMAC_INTSTS_RXGDIF_Msk           (0x1ul << EMAC_INTSTS_RXGDIF_Pos)                 /*!< EMAC_T::INTSTS: RXGDIF Mask            */

#define EMAC_INTSTS_ALIEIF_Pos           (5)                                               /*!< EMAC_T::INTSTS: ALIEIF Position        */
#define EMAC_INTSTS_ALIEIF_Msk           (0x1ul << EMAC_INTSTS_ALIEIF_Pos)                 /*!< EMAC_T::INTSTS: ALIEIF Mask            */

#define EMAC_INTSTS_RPIF_Pos             (6)                                               /*!< EMAC_T::INTSTS: RPIF Position          */
#define EMAC_INTSTS_RPIF_Msk             (0x1ul << EMAC_INTSTS_RPIF_Pos)                   /*!< EMAC_T::INTSTS: RPIF Mask              */

#define EMAC_INTSTS_MPCOVIF_Pos          (7)                                               /*!< EMAC_T::INTSTS: MPCOVIF Position       */
#define EMAC_INTSTS_MPCOVIF_Msk          (0x1ul << EMAC_INTSTS_MPCOVIF_Pos)                /*!< EMAC_T::INTSTS: MPCOVIF Mask           */

#define EMAC_INTSTS_MFLEIF_Pos           (8)                                               /*!< EMAC_T::INTSTS: MFLEIF Position        */
#define EMAC_INTSTS_MFLEIF_Msk           (0x1ul << EMAC_INTSTS_MFLEIF_Pos)                 /*!< EMAC_T::INTSTS: MFLEIF Mask            */

#define EMAC_INTSTS_DENIF_Pos            (9)                                               /*!< EMAC_T::INTSTS: DENIF Position         */
#define EMAC_INTSTS_DENIF_Msk            (0x1ul << EMAC_INTSTS_DENIF_Pos)                  /*!< EMAC_T::INTSTS: DENIF Mask             */

#define EMAC_INTSTS_RDUIF_Pos            (10)                                              /*!< EMAC_T::INTSTS: RDUIF Position         */
#define EMAC_INTSTS_RDUIF_Msk            (0x1ul << EMAC_INTSTS_RDUIF_Pos)                  /*!< EMAC_T::INTSTS: RDUIF Mask             */

#define EMAC_INTSTS_RXBEIF_Pos           (11)                                              /*!< EMAC_T::INTSTS: RXBEIF Position        */
#define EMAC_INTSTS_RXBEIF_Msk           (0x1ul << EMAC_INTSTS_RXBEIF_Pos)                 /*!< EMAC_T::INTSTS: RXBEIF Mask            */

#define EMAC_INTSTS_CFRIF_Pos            (14)                                              /*!< EMAC_T::INTSTS: CFRIF Position         */
#define EMAC_INTSTS_CFRIF_Msk            (0x1ul << EMAC_INTSTS_CFRIF_Pos)                  /*!< EMAC_T::INTSTS: CFRIF Mask             */

#define EMAC_INTSTS_WOLIF_Pos            (15)                                              /*!< EMAC_T::INTSTS: WOLIF Position         */
#define EMAC_INTSTS_WOLIF_Msk            (0x1ul << EMAC_INTSTS_WOLIF_Pos)                  /*!< EMAC_T::INTSTS: WOLIF Mask             */

#define EMAC_INTSTS_TXIF_Pos             (16)                                              /*!< EMAC_T::INTSTS: TXIF Position          */
#define EMAC_INTSTS_TXIF_Msk             (0x1ul << EMAC_INTSTS_TXIF_Pos)                   /*!< EMAC_T::INTSTS: TXIF Mask              */

#define EMAC_INTSTS_TXUDIF_Pos           (17)                                              /*!< EMAC_T::INTSTS: TXUDIF Position        */
#define EMAC_INTSTS_TXUDIF_Msk           (0x1ul << EMAC_INTSTS_TXUDIF_Pos)                 /*!< EMAC_T::INTSTS: TXUDIF Mask            */

#define EMAC_INTSTS_TXCPIF_Pos           (18)                                              /*!< EMAC_T::INTSTS: TXCPIF Position        */
#define EMAC_INTSTS_TXCPIF_Msk           (0x1ul << EMAC_INTSTS_TXCPIF_Pos)                 /*!< EMAC_T::INTSTS: TXCPIF Mask            */

#define EMAC_INTSTS_EXDEFIF_Pos          (19)                                              /*!< EMAC_T::INTSTS: EXDEFIF Position       */
#define EMAC_INTSTS_EXDEFIF_Msk          (0x1ul << EMAC_INTSTS_EXDEFIF_Pos)                /*!< EMAC_T::INTSTS: EXDEFIF Mask           */

#define EMAC_INTSTS_NCSIF_Pos            (20)                                              /*!< EMAC_T::INTSTS: NCSIF Position         */
#define EMAC_INTSTS_NCSIF_Msk            (0x1ul << EMAC_INTSTS_NCSIF_Pos)                  /*!< EMAC_T::INTSTS: NCSIF Mask             */

#define EMAC_INTSTS_TXABTIF_Pos          (21)                                              /*!< EMAC_T::INTSTS: TXABTIF Position       */
#define EMAC_INTSTS_TXABTIF_Msk          (0x1ul << EMAC_INTSTS_TXABTIF_Pos)                /*!< EMAC_T::INTSTS: TXABTIF Mask           */

#define EMAC_INTSTS_LCIF_Pos             (22)                                              /*!< EMAC_T::INTSTS: LCIF Position          */
#define EMAC_INTSTS_LCIF_Msk             (0x1ul << EMAC_INTSTS_LCIF_Pos)                   /*!< EMAC_T::INTSTS: LCIF Mask              */

#define EMAC_INTSTS_TDUIF_Pos            (23)                                              /*!< EMAC_T::INTSTS: TDUIF Position         */
#define EMAC_INTSTS_TDUIF_Msk            (0x1ul << EMAC_INTSTS_TDUIF_Pos)                  /*!< EMAC_T::INTSTS: TDUIF Mask             */

#define EMAC_INTSTS_TXBEIF_Pos           (24)                                              /*!< EMAC_T::INTSTS: TXBEIF Position        */
#define EMAC_INTSTS_TXBEIF_Msk           (0x1ul << EMAC_INTSTS_TXBEIF_Pos)                 /*!< EMAC_T::INTSTS: TXBEIF Mask            */

#define EMAC_INTSTS_TSALMIF_Pos          (28)                                              /*!< EMAC_T::INTSTS: TSALMIF Position       */
#define EMAC_INTSTS_TSALMIF_Msk          (0x1ul << EMAC_INTSTS_TSALMIF_Pos)                /*!< EMAC_T::INTSTS: TSALMIF Mask           */

#define EMAC_GENSTS_CFR_Pos              (0)                                               /*!< EMAC_T::GENSTS: CFR Position           */
#define EMAC_GENSTS_CFR_Msk              (0x1ul << EMAC_GENSTS_CFR_Pos)                    /*!< EMAC_T::GENSTS: CFR Mask               */

#define EMAC_GENSTS_RXHALT_Pos           (1)                                               /*!< EMAC_T::GENSTS: RXHALT Position        */
#define EMAC_GENSTS_RXHALT_Msk           (0x1ul << EMAC_GENSTS_RXHALT_Pos)                 /*!< EMAC_T::GENSTS: RXHALT Mask            */

#define EMAC_GENSTS_RXFFULL_Pos          (2)                                               /*!< EMAC_T::GENSTS: RXFFULL Position       */
#define EMAC_GENSTS_RXFFULL_Msk          (0x1ul << EMAC_GENSTS_RXFFULL_Pos)                /*!< EMAC_T::GENSTS: RXFFULL Mask           */

#define EMAC_GENSTS_COLCNT_Pos           (4)                                               /*!< EMAC_T::GENSTS: COLCNT Position        */
#define EMAC_GENSTS_COLCNT_Msk           (0xful << EMAC_GENSTS_COLCNT_Pos)                 /*!< EMAC_T::GENSTS: COLCNT Mask            */

#define EMAC_GENSTS_DEF_Pos              (8)                                               /*!< EMAC_T::GENSTS: DEF Position           */
#define EMAC_GENSTS_DEF_Msk              (0x1ul << EMAC_GENSTS_DEF_Pos)                    /*!< EMAC_T::GENSTS: DEF Mask               */

#define EMAC_GENSTS_TXPAUSED_Pos         (9)                                               /*!< EMAC_T::GENSTS: TXPAUSED Position      */
#define EMAC_GENSTS_TXPAUSED_Msk         (0x1ul << EMAC_GENSTS_TXPAUSED_Pos)               /*!< EMAC_T::GENSTS: TXPAUSED Mask          */

#define EMAC_GENSTS_SQE_Pos              (10)                                              /*!< EMAC_T::GENSTS: SQE Position           */
#define EMAC_GENSTS_SQE_Msk              (0x1ul << EMAC_GENSTS_SQE_Pos)                    /*!< EMAC_T::GENSTS: SQE Mask               */

#define EMAC_GENSTS_TXHALT_Pos           (11)                                              /*!< EMAC_T::GENSTS: TXHALT Position        */
#define EMAC_GENSTS_TXHALT_Msk           (0x1ul << EMAC_GENSTS_TXHALT_Pos)                 /*!< EMAC_T::GENSTS: TXHALT Mask            */

#define EMAC_GENSTS_RPSTS_Pos            (12)                                              /*!< EMAC_T::GENSTS: RPSTS Position         */
#define EMAC_GENSTS_RPSTS_Msk            (0x1ul << EMAC_GENSTS_RPSTS_Pos)                  /*!< EMAC_T::GENSTS: RPSTS Mask             */

#define EMAC_MPCNT_MPCNT_Pos             (0)                                               /*!< EMAC_T::MPCNT: MPCNT Position          */
#define EMAC_MPCNT_MPCNT_Msk             (0xfffful << EMAC_MPCNT_MPCNT_Pos)                /*!< EMAC_T::MPCNT: MPCNT Mask              */

#define EMAC_RPCNT_RPCNT_Pos             (0)                                               /*!< EMAC_T::RPCNT: RPCNT Position          */
#define EMAC_RPCNT_RPCNT_Msk             (0xfffful << EMAC_RPCNT_RPCNT_Pos)                /*!< EMAC_T::RPCNT: RPCNT Mask              */

#define EMAC_FRSTS_RXFLT_Pos             (0)                                               /*!< EMAC_T::FRSTS: RXFLT Position          */
#define EMAC_FRSTS_RXFLT_Msk             (0xfffful << EMAC_FRSTS_RXFLT_Pos)                /*!< EMAC_T::FRSTS: RXFLT Mask              */

#define EMAC_CTXDSA_CTXDSA_Pos           (0)                                               /*!< EMAC_T::CTXDSA: CTXDSA Position        */
#define EMAC_CTXDSA_CTXDSA_Msk           (0xfffffffful << EMAC_CTXDSA_CTXDSA_Pos)          /*!< EMAC_T::CTXDSA: CTXDSA Mask            */

#define EMAC_CTXBSA_CTXBSA_Pos           (0)                                               /*!< EMAC_T::CTXBSA: CTXBSA Position        */
#define EMAC_CTXBSA_CTXBSA_Msk           (0xfffffffful << EMAC_CTXBSA_CTXBSA_Pos)          /*!< EMAC_T::CTXBSA: CTXBSA Mask            */

#define EMAC_CRXDSA_CRXDSA_Pos           (0)                                               /*!< EMAC_T::CRXDSA: CRXDSA Position        */
#define EMAC_CRXDSA_CRXDSA_Msk           (0xfffffffful << EMAC_CRXDSA_CRXDSA_Pos)          /*!< EMAC_T::CRXDSA: CRXDSA Mask            */

#define EMAC_CRXBSA_CRXBSA_Pos           (0)                                               /*!< EMAC_T::CRXBSA: CRXBSA Position        */
#define EMAC_CRXBSA_CRXBSA_Msk           (0xfffffffful << EMAC_CRXBSA_CRXBSA_Pos)          /*!< EMAC_T::CRXBSA: CRXBSA Mask            */

#define EMAC_TSCTL_TSEN_Pos              (0)                                               /*!< EMAC_T::TSCTL: TSEN Position           */
#define EMAC_TSCTL_TSEN_Msk              (0x1ul << EMAC_TSCTL_TSEN_Pos)                    /*!< EMAC_T::TSCTL: TSEN Mask               */

#define EMAC_TSCTL_TSIEN_Pos             (1)                                               /*!< EMAC_T::TSCTL: TSIEN Position          */
#define EMAC_TSCTL_TSIEN_Msk             (0x1ul << EMAC_TSCTL_TSIEN_Pos)                   /*!< EMAC_T::TSCTL: TSIEN Mask              */

#define EMAC_TSCTL_TSMODE_Pos            (2)                                               /*!< EMAC_T::TSCTL: TSMODE Position         */
#define EMAC_TSCTL_TSMODE_Msk            (0x1ul << EMAC_TSCTL_TSMODE_Pos)                  /*!< EMAC_T::TSCTL: TSMODE Mask             */

#define EMAC_TSCTL_TSUPDATE_Pos          (3)                                               /*!< EMAC_T::TSCTL: TSUPDATE Position       */
#define EMAC_TSCTL_TSUPDATE_Msk          (0x1ul << EMAC_TSCTL_TSUPDATE_Pos)                /*!< EMAC_T::TSCTL: TSUPDATE Mask           */

#define EMAC_TSCTL_TSALMEN_Pos           (5)                                               /*!< EMAC_T::TSCTL: TSALMEN Position        */
#define EMAC_TSCTL_TSALMEN_Msk           (0x1ul << EMAC_TSCTL_TSALMEN_Pos)                 /*!< EMAC_T::TSCTL: TSALMEN Mask            */

#define EMAC_TSSEC_SEC_Pos               (0)                                               /*!< EMAC_T::TSSEC: SEC Position            */
#define EMAC_TSSEC_SEC_Msk               (0xfffffffful << EMAC_TSSEC_SEC_Pos)              /*!< EMAC_T::TSSEC: SEC Mask                */

#define EMAC_TSSUBSEC_SUBSEC_Pos         (0)                                               /*!< EMAC_T::TSSUBSEC: SUBSEC Position      */
#define EMAC_TSSUBSEC_SUBSEC_Msk         (0xfffffffful << EMAC_TSSUBSEC_SUBSEC_Pos)        /*!< EMAC_T::TSSUBSEC: SUBSEC Mask          */

#define EMAC_TSINC_CNTINC_Pos            (0)                                               /*!< EMAC_T::TSINC: CNTINC Position         */
#define EMAC_TSINC_CNTINC_Msk            (0xfful << EMAC_TSINC_CNTINC_Pos)                 /*!< EMAC_T::TSINC: CNTINC Mask             */

#define EMAC_TSADDEND_ADDEND_Pos         (0)                                               /*!< EMAC_T::TSADDEND: ADDEND Position      */
#define EMAC_TSADDEND_ADDEND_Msk         (0xfffffffful << EMAC_TSADDEND_ADDEND_Pos)        /*!< EMAC_T::TSADDEND: ADDEND Mask          */

#define EMAC_UPDSEC_SEC_Pos              (0)                                               /*!< EMAC_T::UPDSEC: SEC Position           */
#define EMAC_UPDSEC_SEC_Msk              (0xfffffffful << EMAC_UPDSEC_SEC_Pos)             /*!< EMAC_T::UPDSEC: SEC Mask               */

#define EMAC_UPDSUBSEC_SUBSEC_Pos        (0)                                               /*!< EMAC_T::UPDSUBSEC: SUBSEC Position     */
#define EMAC_UPDSUBSEC_SUBSEC_Msk        (0xfffffffful << EMAC_UPDSUBSEC_SUBSEC_Pos)       /*!< EMAC_T::UPDSUBSEC: SUBSEC Mask         */

#define EMAC_ALMSEC_SEC_Pos              (0)                                               /*!< EMAC_T::ALMSEC: SEC Position           */
#define EMAC_ALMSEC_SEC_Msk              (0xfffffffful << EMAC_ALMSEC_SEC_Pos)             /*!< EMAC_T::ALMSEC: SEC Mask               */

#define EMAC_ALMSUBSEC_SUBSEC_Pos        (0)                                               /*!< EMAC_T::ALMSUBSEC: SUBSEC Position     */
#define EMAC_ALMSUBSEC_SUBSEC_Msk        (0xfffffffful << EMAC_ALMSUBSEC_SUBSEC_Pos)       /*!< EMAC_T::ALMSUBSEC: SUBSEC Mask         */

/**@}*/ /* EMAC_CONST */
/**@}*/ /* end of EMAC register group */
/**@}*/ /* end of REGISTER group */

#if defined ( __CC_ARM   )
    #pragma no_anon_unions
#endif

#endif /* __EMAC_REG_H__ */