| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196 |
- menu "Hardware Drivers Config"
- config SOC_APM32F030RB
- bool
- select SOC_SERIES_APM32F0
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_USING_UART2
- bool "Enable UART2"
- default n
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- menuconfig BSP_USING_DAC
- bool "Enable DAC"
- default n
- select RT_USING_DAC
- if BSP_USING_DAC
- config BSP_USING_DAC1
- bool "Enable DAC1"
- default n
- endif
- menuconfig BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- default n
- if BSP_USING_ONCHIP_RTC
- choice
- prompt "Select clock source"
- default BSP_RTC_USING_LSE
- config BSP_RTC_USING_LSE
- bool "RTC USING LSE"
- config BSP_RTC_USING_LSI
- bool "RTC USING LSI"
- endchoice
- endif
- menuconfig BSP_USING_I2C
- bool "Enable I2C BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C
- config BSP_USING_I2C1
- bool "Enable I2C1 BUS"
- if BSP_USING_I2C1
- comment "Notice: PB10 --> 26; PB11 --> 27"
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 0 63
- default 26
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 0 63
- default 27
- endif
- config BSP_USING_I2C2
- bool "Enable I2C2 BUS"
- if BSP_USING_I2C2
- comment "Notice: PA0 --> 0; PA1 --> 1"
- config BSP_I2C2_SCL_PIN
- int "i2c2 scl pin number"
- range 0 63
- default 22
- config BSP_I2C2_SDA_PIN
- int "I2C2 sda pin number"
- range 0 63
- default 23
- endif
- endif
- menuconfig BSP_USING_SPI
- bool "Enable SPI"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI1
- bool "Enable SPI1"
- default n
- config BSP_USING_SPI2
- bool "Enable SPI2"
- default n
- endif
- menuconfig BSP_USING_TMR
- bool "Enable Timer"
- default n
- select RT_USING_HWTIMER
- if BSP_USING_TMR
- config BSP_USING_TMR1
- bool "Enable TMR1"
- default n
- config BSP_USING_TMR3
- bool "Enable TMR3"
- default n
- config BSP_USING_TMR6
- bool "Enable TMR6"
- default n
- config BSP_USING_TMR7
- bool "Enable TMR7"
- default n
- config BSP_USING_TMR14
- bool "Enable TMR14"
- default n
- config BSP_USING_TMR15
- bool "Enable TMR15"
- default n
- config BSP_USING_TMR16
- bool "Enable TMR16"
- default n
- config BSP_USING_TMR17
- bool "Enable TMR17"
- default n
- endif
- menuconfig BSP_USING_PWM
- bool "Enable PWM"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM3
- bool "Enable timer3 output PWM"
- default n
- if BSP_USING_PWM3
- config BSP_USING_PWM3_CH1
- bool "Enable PWM3 channel1"
- default n
- config BSP_USING_PWM3_CH2
- bool "Enable PWM3 channel2"
- default n
- config BSP_USING_PWM3_CH3
- bool "Enable PWM3 channel3"
- default n
- config BSP_USING_PWM3_CH4
- bool "Enable PWM3 channel4"
- default n
- endif
- endif
- config BSP_USING_WDT
- bool "Enable Watchdog Timer"
- select RT_USING_WDT
- default n
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
