| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158 |
- menu "Hardware Drivers Config"
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_STM32_UART_V1_TX_TIMEOUT
- int "UART TX timeout"
- default 6000
- depends on RT_USING_SERIAL_V1
-
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_UART1_RX_USING_DMA
- bool "Enable UART1 RX DMA"
- depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
- default n
- config BSP_USING_UART2
- bool "Enable UART2"
- default n
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- config BSP_USING_LPUART1
- bool "Enable LPUART1"
- default n
- config BSP_LPUART1_RX_USING_DMA
- bool "Enable LPUART1 RX DMA"
- depends on BSP_USING_LPUART1 && RT_SERIAL_USING_DMA
- default n
- endif
- config BSP_USING_QSPI
- bool "Enable QSPI BUS"
- select RT_USING_QSPI
- select RT_USING_SPI
- default n
- config BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- default n
- source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"
- endmenu
- menu "Onboard Peripheral Drivers"
- config BSP_USING_SDRAM
- bool "Enable SDRAM"
- default n
- config BSP_USING_QSPI_FLASH
- bool "Enable QSPI FLASH (W25Q256 qspi)"
- select BSP_USING_QSPI
- select RT_USING_SFUD
- select RT_SFUD_USING_QSPI
- default n
- config BSP_USING_SDMMC
- bool "Enable SDMMC (SD card)"
- select RT_USING_SDIO
- select RT_USING_DFS
- select RT_USING_DFS_ELMFAT
- default n
- config BSP_USING_USBD
- bool "Enable OTGFS as USB device"
- select RT_USING_USB_DEVICE
- default n
- config BSP_USING_OV5640
- bool "Enable camera (ov5640)"
- select BSP_USING_DCMI
- select BSP_USING_I2C
- select BSP_USING_I2C1
- select BSP_USING_PWM
- select BSP_USING_PWM1
- select BSP_USING_PWM1_CH1
- default n
- config BSP_USING_DCMI
- bool "Enable DCMI"
- default n
- menuconfig BSP_USING_I2C
- bool "Enable I2C BUS (software simulation)"
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- default n
- if BSP_USING_I2C
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- if BSP_USING_I2C1
- comment "Notice: PB8 --> 24; PB9 --> 25"
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 1 176
- default 24
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 176
- default 25
- endif
- menuconfig BSP_USING_I2C2
- bool "Enable I2C2 BUS (software simulation)"
- default n
- if BSP_USING_I2C2
- comment "Notice: PB10 --> 26; PB11 --> 27"
- config BSP_I2C2_SCL_PIN
- int "i2c2 scl pin number"
- range 1 176
- default 26
- config BSP_I2C2_SDA_PIN
- int "I2C2 sda pin number"
- range 1 176
- default 27
- endif
- endif
- menuconfig BSP_USING_PWM
- bool "Enable PWM"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM1
- bool "Enable timer1 output pwm"
- default n
- if BSP_USING_PWM1
- config BSP_USING_PWM1_CH1
- bool "Enable PWM1 channel1"
- default n
- endif
- endif
- endmenu
- endmenu
|
