| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201 |
- menu "Hardware Drivers Config"
- menu "Onboard Peripheral Drivers"
- config BSP_USING_USB_TO_USART
- bool "Enable USB TO USART (uart1)"
- select BSP_USING_UART
- select BSP_USING_UART1
- default y
- config BSP_USING_ARDUINO
- bool "Compatible with Arduino Ecosystem (RTduino)"
- select PKG_USING_RTDUINO
- select BSP_USING_STLINK_TO_USART
- select BSP_USING_UART2
- select BSP_USING_UART3
- select BSP_USING_GPIO
- select BSP_USING_ADC
- select BSP_USING_ADC1
- select BSP_USING_PWM
- select BSP_USING_PWM2
- select BSP_USING_PWM2_CH1
- select BSP_USING_PWM2_CH2
- select BSP_USING_PWM3
- select BSP_USING_PWM3_CH1
- select BSP_USING_PWM3_CH2
- select BSP_USING_PWM3_CH3
- select BSP_USING_PWM3_CH4
- select BSP_USING_I2C
- select BSP_USING_I2C1
- select BSP_USING_SPI
- select BSP_USING_SPI2
- # select BSP_SPI2_TX_USING_DMA
- # select BSP_SPI2_RX_USING_DMA
- select RTDUINO_USING_WIRE
- select RTDUINO_USING_SPI
- imply RTDUINO_USING_SERVO
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_UART1_RX_USING_DMA
- bool "Enable UART1 RX DMA"
- depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
- default n
- config BSP_USING_UART2
- bool "Enable UART2"
- default n
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- config BSP_USING_UART3
- bool "Enable UART3"
- default n
- config BSP_UART3_RX_USING_DMA
- bool "Enable UART3 RX DMA"
- depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
- default n
- endif
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number (PB8)"
- range 0 143
- default 24
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number (PB9)"
- range 0 143
- default 25
- endif
- menuconfig BSP_USING_PWM
- bool "Enable PWM"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM2
- bool "Enable timer2 output PWM"
- default n
- if BSP_USING_PWM2
- config BSP_USING_PWM2_CH1
- bool "Enable PWM2 channel1"
- default n
- config BSP_USING_PWM2_CH2
- bool "Enable PWM2 channel2"
- default n
- endif
- menuconfig BSP_USING_PWM3
- bool "Enable timer3 output PWM"
- default n
- if BSP_USING_PWM3
- config BSP_USING_PWM3_CH1
- bool "Enable PWM3 channel1"
- default n
- config BSP_USING_PWM3_CH2
- bool "Enable PWM3 channel2"
- default n
- config BSP_USING_PWM3_CH3
- bool "Enable PWM3 channel3"
- default n
- config BSP_USING_PWM3_CH4
- bool "Enable PWM3 channel4"
- default n
- endif
- endif
- menuconfig BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- default n
- if BSP_USING_ONCHIP_RTC
- choice
- prompt "Select clock source"
- default BSP_RTC_USING_LSE
- config BSP_RTC_USING_LSE
- bool "RTC USING LSE"
- config BSP_RTC_USING_LSI
- bool "RTC USING LSI"
- endchoice
- endif
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI2
- bool "Enable SPI2 BUS"
- default n
- config BSP_SPI2_TX_USING_DMA
- bool "Enable SPI2 TX DMA"
- depends on BSP_USING_SPI2
- default n
- config BSP_SPI2_RX_USING_DMA
- bool "Enable SPI2 RX DMA"
- depends on BSP_USING_SPI2
- select BSP_SPI2_TX_USING_DMA
- default n
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- config BSP_USING_USBD
- bool "Enable USB device"
- select RT_USING_USB_DEVICE
- default n
- source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig"
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
