| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137 |
- menu "Hardware Drivers Config"
- config SOC_STM32F411RE
- bool
- select SOC_SERIES_STM32F4
- default y
- menu "Onboard Peripheral Drivers"
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART2
- bool "Enable UART2"
- default y
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- config BSP_USING_UART6
- bool "Enable UART6"
- default y
- config BSP_UART6_RX_USING_DMA
- bool "Enable UART6 RX DMA"
- depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA
- default n
- endif
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- comment "Notice: PB8 --> 24; PB9 --> 25"
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 0 80
- default 24
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 0 80
- default 25
- endif
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI1
- bool "Enable SPI1 BUS"
- default n
- config BSP_SPI1_TX_USING_DMA
- bool "Enable SPI1 TX DMA"
- depends on BSP_USING_SPI1
- default n
-
- config BSP_SPI1_RX_USING_DMA
- bool "Enable SPI1 RX DMA"
- depends on BSP_USING_SPI1
- select BSP_SPI1_TX_USING_DMA
- default n
- endif
- menuconfig BSP_USING_PWM
- bool "Enable pwm"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM3
- bool "Enable timer3 output pwm"
- default n
- if BSP_USING_PWM3
- config BSP_USING_PWM3_CH1
- bool "Enable PWM3 channel1 (PA6)"
- default n
- config BSP_USING_PWM3_CH2
- bool "Enable PWM3 channel2 (PA7)"
- default n
- config BSP_USING_PWM3_CH3
- bool "Enable PWM3 channel3 (PB0)"
- default n
- config BSP_USING_PWM3_CH4
- bool "Enable PWM3 channel4 (PB1)"
- default n
- endif
- endif
- menuconfig BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- select RT_USING_LIBC
- default n
- if BSP_USING_ONCHIP_RTC
- choice
- prompt "Select clock source"
- default BSP_RTC_USING_LSE
- config BSP_RTC_USING_LSE
- bool "RTC USING LSE"
- config BSP_RTC_USING_LSI
- bool "RTC USING LSI"
- endchoice
- endif
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- default n
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
