| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187 |
- menu "Hardware Drivers Config"
- config SOC_STM32H750VBT6
- bool
- select SOC_SERIES_STM32H7
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_SPI_FLASH
- bool "Enable SPI FLASH (W25Q64 spi1)"
- select BSP_USING_SPI
- select BSP_USING_SPI1
- select RT_USING_DFS
- select PKG_USING_LITTLEFS
- select RT_USING_MTD_NOR
- select RT_USING_FAL
- select FAL_USING_SFUD_PORT
- select RT_USING_SFUD
- select RT_SFUD_USING_SFDP
- default n
- config BSP_USING_QSPI_FLASH
- bool "Enable QSPI FLASH (W25Q64)"
- select BSP_USING_QSPI
- select FAL_USING_SFUD_PORT
- select RT_USING_SFUD
- select RT_SFUD_USING_QSPI
- default n
- config BSP_USING_LCD_SPI
- bool "Enable 0.96' TFT-LCD(ST7735S)"
- select BSP_USING_GPIO
- select BSP_USING_SPI
- select BSP_USING_SPI4
- # select BSP_SPI4_TX_USING_DMA
- select BSP_USING_PWM
- select BSP_USING_PWM1
- select BSP_USING_PWM1_CH2
- default n
- if BSP_USING_LCD_SPI
- choice
- prompt "choice back light"
- default LCD_BACKLIGHT_USING_GPIO
- config LCD_BACKLIGHT_USING_PWM
- bool "LCD_BACKLIGHT_USING_PWM(tim1_ch2 pwm1)"
- config LCD_BACKLIGHT_USING_GPIO
- bool "LCD_BACKLIGHT_USING_GPIO(PE10)"
- endchoice
- endif
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_UART1_RX_USING_DMA
- bool "Enable UART1 RX DMA"
- depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
- default n
- endif
- config BSP_USING_QSPI
- bool "Enable QSPI BUS"
- select RT_USING_QSPI
- select RT_USING_SPI
- default n
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI1
- bool "Enable SPI1 BUS"
- default n
- config BSP_USING_SPI4
- bool "Enable SPI4 BUS"
- default n
- endif
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 1 216
- default 135
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 216
- default 95
- endif
- menuconfig BSP_USING_PWM
- bool "Enable pwm"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM1
- bool "Enable timer1 output pwm"
- default n
- if BSP_USING_PWM1
- config BSP_USING_PWM1_CH1
- bool "Enable PWM1 channel1"
- default n
- config BSP_USING_PWM1_CH2
- bool "Enable PWM1 channel2"
- default n
- config BSP_USING_PWM1_CH3
- bool "Enable PWM1 channel3"
- default n
- config BSP_USING_PWM1_CH4
- bool "Enable PWM1 channel4"
- default n
- endif
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- config BSP_USING_ADC2
- bool "Enable ADC2"
- default n
- config BSP_USING_ADC3
- bool "Enable ADC3"
- default n
- endif
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- default n
- config BSP_USING_SDIO
- bool "Enable SDIO"
- select RT_USING_SDIO
- select RT_USING_DFS
- default n
- config BSP_USING_USBD
- bool "Enable OTGHS as USB device"
- select RT_USING_USB_DEVICE
- select BSP_USBD_TYPE_HS
- select BSP_USBD_SPEED_HS
- select BSP_USBD_PHY_ULPI
- default n
- source "../libraries/HAL_Drivers/Kconfig"
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
