rt-thread/bsp/stm32/stm32l431-BearPi/board/Kconfig

menu "Hardware Drivers Config"

config SOC_STM32L431RC
    bool
    select SOC_SERIES_STM32L4
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default n

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART1_TX_USING_DMA
                bool "Enable UART1 TX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default n

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART3_TX_USING_DMA
                bool "Enable UART3 TX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_LPUART1
                bool "Enable LPUART1"
                default n
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_DAC
        bool "Enable DAC"
        default n
        select RT_USING_DAC
        if BSP_USING_DAC
            config BSP_USING_DAC1
                bool "Enable DAC1"
                default n
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 0 143
                default 22
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 0 143
                default 23
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM1
            bool "Enable timer1 output PWM"
            default n
            if BSP_USING_PWM1
                config BSP_USING_PWM1_CH1
                    bool "Enable PWM1 channel1"
                    default n
            endif
        menuconfig BSP_USING_PWM16
            bool "Enable timer16 output PWM"
            default n
            if BSP_USING_PWM16
                config BSP_USING_PWM16_CH1
                    bool "Enable PWM16 channel1"
                    default n
            endif
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n

            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n

            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n

            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
        endif

    source "../libraries/HAL_Drivers/Kconfig"

endmenu

menu "Onboard Peripheral Drivers"
    config BSP_USING_SPI_LCD
        bool "Enable LCD (spi2)"
        select BSP_USING_SPI
        select BSP_USING_SPI2
        default n

    config BSP_USING_ARDUINO
        bool "Compatible with Arduino Ecosystem (RTduino)"
        select PKG_USING_RTDUINO
        select BSP_USING_STLINK_TO_USART
        select BSP_USING_UART3
        select BSP_USING_GPIO
        select BSP_USING_ADC
        select BSP_USING_ADC1
        select BSP_USING_DAC
        select BSP_USING_DAC1
        select BSP_USING_PWM
        select BSP_USING_PWM1
        select BSP_USING_PWM16
        select BSP_USING_PWM16_CH1
        select BSP_USING_PWM1_CH1
        select BSP_USING_I2C
        select BSP_USING_I2C1
        select BSP_USING_SPI
        select BSP_USING_SPI1
        imply RTDUINO_USING_SERVO
        imply RTDUINO_USING_WIRE
        imply RTDUINO_USING_SPI
        default n

    config BSP_USING_MPU6050
        bool "Enable MPU6050 to read accel data"
        select BSP_USING_I2C
        select BSP_USING_I2C1
        select PKG_USING_MPU6XXX
        default n
        if BSP_USING_MPU6050
            menuconfig BSP_USING_MQTT_HW_CLOUD
                bool "Enable MPU6050 Connect to Huawei Cloud"
                select BSP_USING_LPUART1
                select PKG_USING_CJSON
                select PKG_USING_AT_DEVICE
                select AT_DEVICE_USING_ESP8266
                select PKG_USING_KAWAII_MQTT
                select KAWAII_MQTT_NETSOCKET_USE_SAL
                default n

                if AT_DEVICE_USING_ESP8266
                    config ESP8266_SAMPLE_WIFI_SSID
                        string "WIFI ssid"
                        default "rtthread"

                    config ESP8266_SAMPLE_WIFI_PASSWORD
                        string "WIFI password"
                        default "12345678"

                    config ESP8266_SAMPLE_CLIENT_NAME
                        string "AT client device name"
                        default "lpuart1"
                endif

                if PKG_USING_KAWAII_MQTT
                    config KAWAII_MQTT_HOST
                        string "mqtt host"
                        default "jiejie01.top"

                    config KAWAII_MQTT_PORT
                        string "mqtt port"
                        default "1883"

                    config KAWAII_MQTT_CLIENTID
                        string "mqtt client id"
                        default "rtthread001"

                    config KAWAII_MQTT_USERNAME
                        string "mqtt username"
                        default "rt-thread"

                    config KAWAII_MQTT_PASSWORD
                        string "mqtt password"
                        default "rt-thread"

                    config KAWAII_MQTT_SUBTOPIC
                        string "mqtt subscribe topic"
                        default "rtt-sub"

                    config KAWAII_MQTT_PUBTOPIC
                        string "mqtt publish topic"
                        default "rtt-pub"
                endif
            endif
endmenu

endmenu