rt-thread/bsp/stm32f103vb_lwip/enc28j60.c

#include "enc28j60.h"

#include <netif/ethernetif.h>
#include "lwipopts.h"
#include "stm32f10x_lib.h"

#define MAX_ADDR_LEN    6

#define CSACTIVE    GPIO_ResetBits(GPIOA,  GPIO_Pin_12);
#define CSPASSIVE   GPIO_SetBits(GPIOA,  GPIO_Pin_12);

struct net_device
{
	/* inherit from ethernet device */
	struct eth_device parent;

	/* interface address info. */
	rt_uint8_t  dev_addr[MAX_ADDR_LEN];			/* hw address	*/
};

static struct net_device  enc28j60_dev_entry;
static struct net_device *enc28j60_dev =&enc28j60_dev_entry;
static rt_uint8_t  Enc28j60Bank;
static rt_uint16_t NextPacketPtr;
static struct rt_semaphore tx_sem;

void _delay_us(rt_uint32_t us)
{
	rt_uint32_t len;
	for (;us > 0; us --)
		for (len = 0; len < 20; len++ );
}

void delay_ms(rt_uint32_t ms)
{
	rt_uint32_t len;
	for (;ms > 0; ms --)
		for (len = 0; len < 100; len++ );
}

rt_uint8_t spi_read_op(rt_uint8_t op, rt_uint8_t address)
{
	int temp=0;
	CSACTIVE;

	SPI_I2S_SendData(SPI1, (op | (address & ADDR_MASK)));
	while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);
	SPI_I2S_ReceiveData(SPI1);
	SPI_I2S_SendData(SPI1, 0x00);
	while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);

	// do dummy read if needed (for mac and mii, see datasheet page 29)
	if(address & 0x80)
	{
		SPI_I2S_ReceiveData(SPI1);
		SPI_I2S_SendData(SPI1, 0x00);
		while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);
	}
	// release CS

	temp=SPI_I2S_ReceiveData(SPI1);
	// for(t=0;t<20;t++);
	CSPASSIVE;
	return (temp);
}

void spi_write_op(rt_uint8_t op, rt_uint8_t address, rt_uint8_t data)
{
	rt_uint32_t level;
	
	level = rt_hw_interrupt_disable();
	
	CSACTIVE;
	SPI_I2S_SendData(SPI1, op | (address & ADDR_MASK));
	while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);
	SPI_I2S_SendData(SPI1,data);
	while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);
	CSPASSIVE;
	
	rt_hw_interrupt_enable(level);
}

void enc28j60_set_bank(rt_uint8_t address)
{
	// set the bank (if needed)
	if((address & BANK_MASK) != Enc28j60Bank)
	{
		// set the bank
		spi_write_op(ENC28J60_BIT_FIELD_CLR, ECON1, (ECON1_BSEL1|ECON1_BSEL0));
		spi_write_op(ENC28J60_BIT_FIELD_SET, ECON1, (address & BANK_MASK)>>5);
		Enc28j60Bank = (address & BANK_MASK);
	}
}

rt_uint8_t spi_read(rt_uint8_t address)
{
	// set the bank
	enc28j60_set_bank(address);
	// do the read
	return spi_read_op(ENC28J60_READ_CTRL_REG, address);
}

void spi_write(rt_uint8_t address, rt_uint8_t data)
{
	// set the bank
	enc28j60_set_bank(address);
	// do the write
	spi_write_op(ENC28J60_WRITE_CTRL_REG, address, data);
}

void enc28j60_phy_write(rt_uint8_t address, rt_uint16_t data)
{
	// set the PHY register address
	spi_write(MIREGADR, address);

	// write the PHY data
	spi_write(MIWRL, data);
	spi_write(MIWRH, data>>8);

	// wait until the PHY write completes
	while(spi_read(MISTAT) & MISTAT_BUSY)
	{
		_delay_us(15);
	}
}

// read upper 8 bits
rt_uint16_t enc28j60_phy_read(rt_uint8_t address)
{
	// Set the right address and start the register read operation
	spi_write(MIREGADR, address);
	spi_write(MICMD, MICMD_MIIRD);

	_delay_us(15);

	// wait until the PHY read completes
	while(spi_read(MISTAT) & MISTAT_BUSY);

	// reset reading bit
	spi_write(MICMD, 0x00);

	return (spi_read(MIRDH));
}

void enc28j60_clkout(rt_uint8_t clk)
{
	//setup clkout: 2 is 12.5MHz:
	spi_write(ECOCON, clk & 0x7);
}

/*
 * Access the PHY to determine link status
 */
static void enc28j60_check_link_status()
{
	rt_uint16_t reg;
	int duplex;

	reg = enc28j60_phy_read(PHSTAT2);
	duplex = reg & PHSTAT2_DPXSTAT;

	if (reg & PHSTAT2_LSTAT)
	{
	    /* on */
	}
	else
	{
	    /* off */
	}
}

#ifdef RT_USING_FINSH
#include <finsh.h>
/*
 * Debug routine to dump useful register contents
 */
static void enc28j60(void)
{
	rt_kprintf("-- enc28j60 registers:\n");
	rt_kprintf("HwRevID: 0x%02x\n", spi_read(EREVID));
	rt_kprintf("Cntrl: ECON1 ECON2 ESTAT  EIR  EIE\n");
	rt_kprintf("       0x%02x  0x%02x  0x%02x  0x%02x  0x%02x\n",spi_read(ECON1), spi_read(ECON2), spi_read(ESTAT), spi_read(EIR), spi_read(EIE));
	rt_kprintf("MAC  : MACON1 MACON3 MACON4\n");
	rt_kprintf("       0x%02x   0x%02x   0x%02x\n", spi_read(MACON1), spi_read(MACON3), spi_read(MACON4));
	rt_kprintf("Rx   : ERXST  ERXND  ERXWRPT ERXRDPT ERXFCON EPKTCNT MAMXFL\n");
	rt_kprintf("       0x%04x 0x%04x 0x%04x  0x%04x  ",
		(spi_read(ERXSTH) << 8) | spi_read(ERXSTL),
		(spi_read(ERXNDH) << 8) | spi_read(ERXNDL),
		(spi_read(ERXWRPTH) << 8) | spi_read(ERXWRPTL),
		(spi_read(ERXRDPTH) << 8) | spi_read(ERXRDPTL));
	rt_kprintf("0x%02x    0x%02x    0x%04x\n", spi_read(ERXFCON), spi_read(EPKTCNT),
		(spi_read(MAMXFLH) << 8) | spi_read(MAMXFLL));

	rt_kprintf("Tx   : ETXST  ETXND  MACLCON1 MACLCON2 MAPHSUP\n");
	rt_kprintf("       0x%04x 0x%04x 0x%02x     0x%02x     0x%02x\n",
		(spi_read(ETXSTH) << 8) | spi_read(ETXSTL),
		(spi_read(ETXNDH) << 8) | spi_read(ETXNDL),
		spi_read(MACLCON1), spi_read(MACLCON2), spi_read(MAPHSUP));
}
FINSH_FUNCTION_EXPORT(enc28j60, dump enc28j60 registers)
#endif

/*
 * RX handler
 * ignore PKTIF because is unreliable! (look at the errata datasheet)
 * check EPKTCNT is the suggested workaround.
 * We don't need to clear interrupt flag, automatically done when
 * enc28j60_hw_rx() decrements the packet counter.
 * Returns how many packet processed.
 */
void enc28j60_isr()
{
	/* Variable definitions can be made now. */
	volatile rt_uint32_t eir, pk_counter;
	volatile rt_bool_t rx_activiated;
	
	rx_activiated = RT_FALSE;

	/* get EIR */
	eir = spi_read(EIR);
	// rt_kprintf("eir: 0x%08x\n", eir);

	do
	{
	/* errata #4, PKTIF does not reliable */
    pk_counter = spi_read(EPKTCNT);
    if (pk_counter)
    {
        rt_err_t result;
        /* a frame has been received */
        result = eth_device_ready((struct eth_device*)&(enc28j60_dev->parent));
        RT_ASSERT(result == RT_EOK);
			
			// switch to bank 0
			enc28j60_set_bank(EIE);
			// disable rx interrutps
			spi_write_op(ENC28J60_BIT_FIELD_CLR, EIE, EIE_PKTIE);
    }

	/* clear PKTIF */
	if (eir & EIR_PKTIF)
	{
		enc28j60_set_bank(EIR);
		spi_write_op(ENC28J60_BIT_FIELD_CLR, EIR, EIR_PKTIF);
			
			rx_activiated = RT_TRUE;
	}

	/* clear DMAIF */
    if (eir & EIR_DMAIF)
	{
		enc28j60_set_bank(EIR);
		spi_write_op(ENC28J60_BIT_FIELD_CLR, EIR, EIR_DMAIF);
	}

    /* LINK changed handler */
    if ( eir & EIR_LINKIF)
    {
        enc28j60_check_link_status();

        /* read PHIR to clear the flag */
        enc28j60_phy_read(PHIR);

		enc28j60_set_bank(EIR);
		spi_write_op(ENC28J60_BIT_FIELD_CLR, EIR, EIR_LINKIF);
    }

	if (eir & EIR_TXIF)
	{
		/* A frame has been transmitted. */
		rt_sem_release(&tx_sem);

		enc28j60_set_bank(EIR);
		spi_write_op(ENC28J60_BIT_FIELD_CLR, EIR, EIR_TXIF);
	}
		eir = spi_read(EIR);
		// rt_kprintf("inner eir: 0x%08x\n", eir);
	} while ((rx_activiated != RT_TRUE && eir != 0));
}

/* RT-Thread Device Interface */

/* initialize the interface */
rt_err_t enc28j60_init(rt_device_t dev)
{
	CSPASSIVE;

	// perform system reset
	spi_write_op(ENC28J60_SOFT_RESET, 0, ENC28J60_SOFT_RESET);
	delay_ms(50);
	NextPacketPtr = RXSTART_INIT;

    // Rx start
	spi_write(ERXSTL, RXSTART_INIT&0xFF);
	spi_write(ERXSTH, RXSTART_INIT>>8);
	// set receive pointer address
	spi_write(ERXRDPTL, RXSTOP_INIT&0xFF);
	spi_write(ERXRDPTH, RXSTOP_INIT>>8);
	// RX end
	spi_write(ERXNDL, RXSTOP_INIT&0xFF);
	spi_write(ERXNDH, RXSTOP_INIT>>8);

	// TX start
	spi_write(ETXSTL, TXSTART_INIT&0xFF);
	spi_write(ETXSTH, TXSTART_INIT>>8);
	// set transmission pointer address
	spi_write(EWRPTL, TXSTART_INIT&0xFF);
	spi_write(EWRPTH, TXSTART_INIT>>8);
	// TX end
	spi_write(ETXNDL, TXSTOP_INIT&0xFF);
	spi_write(ETXNDH, TXSTOP_INIT>>8);

	// do bank 1 stuff, packet filter:
    // For broadcast packets we allow only ARP packtets
    // All other packets should be unicast only for our mac (MAADR)
    //
    // The pattern to match on is therefore
    // Type     ETH.DST
    // ARP      BROADCAST
    // 06 08 -- ff ff ff ff ff ff -> ip checksum for theses bytes=f7f9
    // in binary these poitions are:11 0000 0011 1111
    // This is hex 303F->EPMM0=0x3f,EPMM1=0x30
	spi_write(ERXFCON, ERXFCON_UCEN|ERXFCON_CRCEN|ERXFCON_BCEN);

	// do bank 2 stuff
	// enable MAC receive
	spi_write(MACON1, MACON1_MARXEN|MACON1_TXPAUS|MACON1_RXPAUS);
	// enable automatic padding to 60bytes and CRC operations
	// spi_write_op(ENC28J60_BIT_FIELD_SET, MACON3, MACON3_PADCFG0|MACON3_TXCRCEN|MACON3_FRMLNEN);
	spi_write_op(ENC28J60_BIT_FIELD_SET, MACON3, MACON3_PADCFG0 | MACON3_TXCRCEN | MACON3_FRMLNEN | MACON3_FULDPX);
	// bring MAC out of reset

	// set inter-frame gap (back-to-back)
	// spi_write(MABBIPG, 0x12);
	spi_write(MABBIPG, 0x15);

	spi_write(MACON4, MACON4_DEFER);
	spi_write(MACLCON2, 63);

	// set inter-frame gap (non-back-to-back)
	spi_write(MAIPGL, 0x12);
	spi_write(MAIPGH, 0x0C);

	// Set the maximum packet size which the controller will accept
	// Do not send packets longer than MAX_FRAMELEN:
	spi_write(MAMXFLL, MAX_FRAMELEN&0xFF);
	spi_write(MAMXFLH, MAX_FRAMELEN>>8);

    // do bank 3 stuff
    // write MAC address
    // NOTE: MAC address in ENC28J60 is byte-backward
    spi_write(MAADR0, enc28j60_dev->dev_addr[5]);
    spi_write(MAADR1, enc28j60_dev->dev_addr[4]);
    spi_write(MAADR2, enc28j60_dev->dev_addr[3]);
    spi_write(MAADR3, enc28j60_dev->dev_addr[2]);
    spi_write(MAADR4, enc28j60_dev->dev_addr[1]);
    spi_write(MAADR5, enc28j60_dev->dev_addr[0]);

	/* output off */
	spi_write(ECOCON, 0x00);

	// enc28j60_phy_write(PHCON1, 0x00);
	enc28j60_phy_write(PHCON1, PHCON1_PDPXMD); // full duplex
    // no loopback of transmitted frames
	enc28j60_phy_write(PHCON2, PHCON2_HDLDIS);

	enc28j60_set_bank(ECON2);
	spi_write_op(ENC28J60_BIT_FIELD_SET, ECON2, ECON2_AUTOINC);

	// switch to bank 0
	enc28j60_set_bank(ECON1);
	// enable interrutps
	spi_write_op(ENC28J60_BIT_FIELD_SET, EIE, EIE_INTIE|EIE_PKTIE|EIR_TXIF);
	// enable packet reception
	spi_write_op(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_RXEN);

	/* clock out */
	// enc28j60_clkout(2);

	enc28j60_phy_write(PHLCON, 0xD76);	//0x476
	delay_ms(20);

    rt_kprintf("enc28j60 init ok!\n");

    return RT_EOK;
}

/* control the interface */
rt_err_t enc28j60_control(rt_device_t dev, rt_uint8_t cmd, void *args)
{
	switch(cmd)
	{
	case NIOCTL_GADDR:
		/* get mac address */
		if(args) rt_memcpy(args, enc28j60_dev_entry.dev_addr, 6);
		else return -RT_ERROR;
		break;

	default :
		break;
	}

	return RT_EOK;
}

/* Open the ethernet interface */
rt_err_t enc28j60_open(rt_device_t dev, rt_uint16_t oflag)
{
	return RT_EOK;
}

/* Close the interface */
rt_err_t enc28j60_close(rt_device_t dev)
{
	return RT_EOK;
}

/* Read */
rt_size_t enc28j60_read(rt_device_t dev, rt_off_t pos, void* buffer, rt_size_t size)
{
	rt_set_errno(-RT_ENOSYS);
	return 0;
}

/* Write */
rt_size_t enc28j60_write(rt_device_t dev, rt_off_t pos, const void* buffer, rt_size_t size)
{
	rt_set_errno(-RT_ENOSYS);
	return 0;
}

/* ethernet device interface */
/*
 * Transmit packet.
 */
rt_err_t enc28j60_tx( rt_device_t dev, struct pbuf* p)
{
	struct pbuf* q;
	rt_uint32_t len;
	rt_uint8_t* ptr;

	// rt_kprintf("tx pbuf: 0x%08x\n", p);

	/* lock tx operation */
	rt_sem_take(&tx_sem, RT_WAITING_FOREVER);

	// Set the write pointer to start of transmit buffer area
	spi_write(EWRPTL, TXSTART_INIT&0xFF);
	spi_write(EWRPTH, TXSTART_INIT>>8);
	// Set the TXND pointer to correspond to the packet size given
	spi_write(ETXNDL, (TXSTART_INIT+ p->tot_len + 1)&0xFF);
	spi_write(ETXNDH, (TXSTART_INIT+ p->tot_len + 1)>>8);

	// write per-packet control byte (0x00 means use macon3 settings)
	spi_write_op(ENC28J60_WRITE_BUF_MEM, 0, 0x00);

	for (q = p; q != NULL; q = q->next)
	{
        CSACTIVE;

		SPI_I2S_SendData(SPI1, ENC28J60_WRITE_BUF_MEM);
		while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);

		len = q->len;
		ptr = q->payload;
        while(len)
        {
			SPI_I2S_SendData(SPI1,*ptr) ;
			while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);;
				ptr++;

			len--;
        }

        CSPASSIVE;
	}

	// send the contents of the transmit buffer onto the network
	spi_write_op(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_TXRTS);
	// Reset the transmit logic problem. See Rev. B4 Silicon Errata point 12.
	if( (spi_read(EIR) & EIR_TXERIF) )
	{
		spi_write_op(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_TXRTS);
	}

	// rt_kprintf("tx ok\n");

    return RT_EOK;
}

struct pbuf *enc28j60_rx(rt_device_t dev)
{
	struct pbuf* p;
	rt_uint32_t len;
	rt_uint16_t rxstat;
	rt_uint32_t pk_counter;

    p = RT_NULL;

    pk_counter = spi_read(EPKTCNT);
    if (pk_counter)
    {
        // Set the read pointer to the start of the received packet
        spi_write(ERDPTL, (NextPacketPtr));
        spi_write(ERDPTH, (NextPacketPtr)>>8);

        // read the next packet pointer
        NextPacketPtr  = spi_read_op(ENC28J60_READ_BUF_MEM, 0);
        NextPacketPtr |= spi_read_op(ENC28J60_READ_BUF_MEM, 0)<<8;

        // read the packet length (see datasheet page 43)
        len  = spi_read_op(ENC28J60_READ_BUF_MEM, 0);	    //0x54
        len |= spi_read_op(ENC28J60_READ_BUF_MEM, 0) <<8;	//5554

        len-=4; //remove the CRC count

        // read the receive status (see datasheet page 43)
        rxstat  = spi_read_op(ENC28J60_READ_BUF_MEM, 0);
        rxstat |= ((rt_uint16_t)spi_read_op(ENC28J60_READ_BUF_MEM, 0))<<8;

        // check CRC and symbol errors (see datasheet page 44, table 7-3):
        // The ERXFCON.CRCEN is set by default. Normally we should not
        // need to check this.
        if ((rxstat & 0x80)==0)
        {
            // invalid
            len=0;
        }
        else
        {
            /* allocation pbuf */
            p = pbuf_alloc(PBUF_LINK, len, PBUF_RAM);
            if (p != RT_NULL)
            {
                rt_uint8_t* data;
                struct pbuf* q;

                for (q = p; q != RT_NULL; q= q->next)
                {
                    data = q->payload;
                    len = q->len;

                    CSACTIVE;

                    SPI_I2S_SendData(SPI1,ENC28J60_READ_BUF_MEM);
                    while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);

                    SPI_I2S_ReceiveData(SPI1);

                    while(len)
                    {
                        len--;
                        SPI_I2S_SendData(SPI1,0x00)	;
                        while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_BSY)==SET);

                        *data= SPI_I2S_ReceiveData(SPI1);
                        data++;
                    }

                    CSPASSIVE;
                }
            }
        }

        // Move the RX read pointer to the start of the next received packet
        // This frees the memory we just read out
        spi_write(ERXRDPTL, (NextPacketPtr));
        spi_write(ERXRDPTH, (NextPacketPtr)>>8);

        // decrement the packet counter indicate we are done with this packet
        spi_write_op(ENC28J60_BIT_FIELD_SET, ECON2, ECON2_PKTDEC);
    }
	else
	{
		rt_uint32_t level;
		/* lock enc28j60 */
		level = rt_hw_interrupt_disable();
		
		// switch to bank 0
		enc28j60_set_bank(EIE);
		// enable interrutps
		spi_write_op(ENC28J60_BIT_FIELD_SET, EIE, EIE_PKTIE);
		// switch to bank 0
		enc28j60_set_bank(ECON1);
		// enable packet reception
		spi_write_op(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_RXEN);
		
		/* enable interrupt */
		rt_hw_interrupt_enable(level);
	}

    return p;
}

static void RCC_Configuration(void)
{
    /* enable spi1 clock */
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);

    /* enable gpioa port clock */
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOD | RCC_APB2Periph_AFIO, ENABLE);
}

static void NVIC_Configuration(void)
{
    NVIC_InitTypeDef NVIC_InitStructure;

    /* Configure one bit for preemption priority */
    NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);

    /* Enable the EXTI0 Interrupt */
    NVIC_InitStructure.NVIC_IRQChannel = EXTI9_5_IRQChannel;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);
}

static void GPIO_Configuration()
{
	GPIO_InitTypeDef GPIO_InitStructure;
    EXTI_InitTypeDef EXTI_InitStructure;

	/* configure PA8 as external interrupt */
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
	GPIO_Init(GPIOA, &GPIO_InitStructure);

    /* Configure SPI1 pins:  SCK, MISO and MOSI ----------------------------*/
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5 | GPIO_Pin_6 | GPIO_Pin_7;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
	GPIO_Init(GPIOD, &GPIO_InitStructure);

    /* Connect ENC28J60 EXTI Line to GPIOB Pin 0 */
    GPIO_EXTILineConfig(GPIO_PortSourceGPIOA, GPIO_PinSource8);

    /* Configure ENC28J60 EXTI Line to generate an interrupt on falling edge */
    EXTI_InitStructure.EXTI_Line = EXTI_Line8;
    EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
    EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
    EXTI_InitStructure.EXTI_LineCmd = ENABLE;
    EXTI_Init(&EXTI_InitStructure);

	/* Clear the Key Button EXTI line pending bit */
	EXTI_ClearITPendingBit(EXTI_Line8);
}

static void SetupSPI (void)
{
    SPI_InitTypeDef SPI_InitStructure;
    SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
    SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
    SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
    SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low;
    SPI_InitStructure.SPI_CPHA = SPI_CPHA_1Edge;
    SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
    SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_4;
    SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
    SPI_InitStructure.SPI_CRCPolynomial = 7;
    SPI_Init(SPI1, &SPI_InitStructure);
    SPI_Cmd(SPI1, ENABLE);
}

static rt_timer_t enc28j60_timer;
void rt_hw_enc28j60_timeout(void* parameter)
{
	// switch to bank 0
	enc28j60_set_bank(EIE);
	// enable interrutps
	spi_write_op(ENC28J60_BIT_FIELD_SET, EIE, EIE_PKTIE);
	// switch to bank 0
	enc28j60_set_bank(ECON1);
	// enable packet reception
	spi_write_op(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_RXEN);

	enc28j60_isr();
}

int rt_hw_enc28j60_init()
{
	rt_err_t result;

	/* configuration PB5 as INT */
	RCC_Configuration();
	NVIC_Configuration();
	GPIO_Configuration();
	SetupSPI();

	/* init rt-thread device interface */
	enc28j60_dev_entry.parent.parent.init		= enc28j60_init;
	enc28j60_dev_entry.parent.parent.open		= enc28j60_open;
	enc28j60_dev_entry.parent.parent.close		= enc28j60_close;
	enc28j60_dev_entry.parent.parent.read		= enc28j60_read;
	enc28j60_dev_entry.parent.parent.write		= enc28j60_write;
	enc28j60_dev_entry.parent.parent.control	= enc28j60_control;
	enc28j60_dev_entry.parent.eth_rx			= enc28j60_rx;
	enc28j60_dev_entry.parent.eth_tx			= enc28j60_tx;

	/* Update MAC address */
	enc28j60_dev_entry.dev_addr[0] = 0x1e;
	enc28j60_dev_entry.dev_addr[1] = 0x30;
	enc28j60_dev_entry.dev_addr[2] = 0x6c;
	enc28j60_dev_entry.dev_addr[3] = 0xa2;
	enc28j60_dev_entry.dev_addr[4] = 0x45;
	enc28j60_dev_entry.dev_addr[5] = 0x5e;

	rt_sem_init(&tx_sem, "emac", 1, RT_IPC_FLAG_FIFO);

	result = eth_device_init(&(enc28j60_dev->parent), "E0");

	/* workaround for enc28j60 interrupt */
	enc28j60_timer = rt_timer_create("etimer", 
		rt_hw_enc28j60_timeout, RT_NULL, 
		50, RT_TIMER_FLAG_PERIODIC);
	if (enc28j60_timer != RT_NULL)
		rt_timer_start(enc28j60_timer);

	return RT_EOK;
}