| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148 |
- menu "Hardware Drivers Config"
- config SOC_IMXRT1052CVL5B
- bool
- select SOC_MIMXRT1050_SERIES
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "On-chip Peripheral Drivers"
- config BSP_USING_DMA
- bool "Enable DMA"
- default n
-
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_LPUART
- bool "Enable UART"
- select RT_USING_SERIAL
- default y
-
- if BSP_USING_LPUART
- config BSP_USING_LPUART1
- bool "Enable LPUART1"
- default y
- config BSP_LPUART1_RX_USING_DMA
- bool "Enable LPUART1 RX DMA"
- depends on BSP_USING_LPUART1
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART1_RX_DMA_CHANNEL
- depends on BSP_LPUART1_RX_USING_DMA
- int "Set LPUART1 RX DMA channel (0-32)"
- default 0
- config BSP_LPUART1_TX_USING_DMA
- bool "Enable LPUART1 TX DMA"
- depends on BSP_USING_LPUART1
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART1_TX_DMA_CHANNEL
- depends on BSP_LPUART1_TX_USING_DMA
- int "Set LPUART1 TX DMA channel (0-32)"
- default 1
- endif
- menuconfig BSP_USING_HWTIMER
- bool "Enable GPT"
- default n
- select RT_USING_HWTIMER
- if BSP_USING_TIM
- config BSP_USING_HWTIMER1
- bool "Enable GPT1"
- default n
- config BSP_USING_HWTIMER2
- bool "Enable GPT2"
- default n
- endif
- menuconfig BSP_USING_PWM
- bool "Enable PWM"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM1
- bool "Enable output pwm1"
- default n
- if BSP_USING_PWM1
- config BSP_USING_PWM1_CH3
- bool "Enable PWM1 channel3"
- default n
- endif
- menuconfig BSP_USING_PWM4
- bool "Enable output pwm4"
- default n
- if BSP_USING_PWM4
- config BSP_USING_PWM4_CH0
- bool "Enable PWM4 channel0"
- default n
- config BSP_USING_PWM4_CH1
- bool "Enable PWM4 channel1"
- default n
- endif
- endif
- menuconfig BSP_USING_I2C
- bool "Enable I2C"
- select RT_USING_I2C
- default n
- if BSP_USING_I2C
- config BSP_USING_I2C1
- bool "Enable I2C1"
- default n
- choice
- prompt "Select I2C1 badurate"
- default HW_I2C1_BADURATE_100kHZ
- config HW_I2C1_BADURATE_100kHZ
- bool "Badurate 100kHZ"
- config HW_I2C1_BADURATE_400kHZ
- bool "Badurate 400kHZ"
- endchoice
- endif
- config BSP_USING_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- default n
- endmenu
- menu "Onboard Peripheral Drivers"
- config BSP_USING_RGB
- bool "Enable RGB LED (PWM1_CH3A, PWM4_CH0A and PWM4_CH1A)"
- select BSP_USING_PWM1
- select BSP_USING_PWM4
- select BSP_USING_PWM1_CH3
- select BSP_USING_PWM4_CH0
- select BSP_USING_PWM4_CH1
- default n
- config BSP_USING_MPU6050
- bool "Enable MPU6050 (I2C1:J11 --> SCL; K11 --> SDA)"
- select BSP_USING_I2C1
- select PKG_USING_MPU6XXX
- default n
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
