| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147 |
- menu "Hardware Drivers Config"
- config SOC_STM32H750IB
- bool
- select SOC_SERIES_STM32H7
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_QSPI_FLASH
- bool "Enable QSPI FLASH (W25Q256)"
- select BSP_USING_QSPI
- select RT_USING_SFUD
- select RT_SFUD_USING_QSPI
- default n
- config PHY_USING_LAN8720A
- bool
- menuconfig BSP_USING_ETH
- bool "Enable Ethernet"
- select RT_USING_LWIP
- select PHY_USING_LAN8720A
- default n
- config BSP_USING_LCD
- bool "Enable LCD"
- select BSP_USING_PWM
- default n
- config BSP_USING_ESP32
- bool "Enable ESP32"
- select BSP_USING_UART4
- select RT_USING_AT
- select AT_USING_CLIENT
- select AT_USING_SOCKET
- select PKG_USING_AT_DEVICE
- select AT_DEVICE_USING_ESP32
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_USING_UART4
- bool "Enable UART4"
- default y
- endif
- config BSP_USING_QSPI
- bool "Enable QSPI BUS"
- select RT_USING_QSPI
- select RT_USING_SPI
- default n
- config BSP_QSPI_USING_DMA
- bool "Enable QSPI DMA support"
- default n
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 1 216
- default 135
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 216
- default 95
- endif
- menuconfig BSP_USING_PWM
- bool "Enable pwm"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM2
- bool "Enable timer2 output pwm"
- default n
- if BSP_USING_PWM2
- config BSP_USING_PWM2_CH2
- bool "Enable PWM2 channel2"
- default n
- endif
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- config BSP_USING_ADC2
- bool "Enable ADC2"
- default n
- config BSP_USING_ADC3
- bool "Enable ADC3"
- default n
- endif
- config BSP_USING_SDIO
- bool "Enable SDIO"
- select RT_USING_SDIO
- select RT_USING_DFS
- default n
- config BSP_USING_USBD
- bool "Enable OTGHS as USB device"
- select RT_USING_USB_DEVICE
- select BSP_USBD_TYPE_HS
- select BSP_USBD_SPEED_HS
- select BSP_USBD_PHY_ULPI
- default n
- source "../libraries/HAL_Drivers/Kconfig"
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
