| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118 |
- menu "Hardware Drivers Config"
- config SOC_STM32L476RG
- bool
- select SOC_SERIES_STM32L4
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_STLINK_TO_USART
- bool "Enable STLINK TO USART (uart2)"
- select BSP_USING_UART
- select BSP_USING_UART2
- default y
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART2
- bool "Enable UART2"
- default n
-
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- endif
-
- menuconfig BSP_USING_I2C
- bool "Enable I2C (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C
- config BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- if BSP_USING_I2C1
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 1 176
- default 22
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 176
- default 23
- endif
- config BSP_USING_I2C2
- bool "Enable I2C2 BUS (software simulation)"
- default n
- if BSP_USING_I2C2
- config BSP_I2C2_SCL_PIN
- int "i2c2 scl pin number"
- range 1 176
- default 26
- config BSP_I2C2_SDA_PIN
- int "I2C2 sda pin number"
- range 1 176
- default 27
- endif
- config BSP_USING_I2C3
- bool "Enable I2C3 BUS (software simulation)"
- default n
- if BSP_USING_I2C3
- config BSP_I2C3_SCL_PIN
- int "i2c3 scl pin number"
- range 1 176
- default 32
- config BSP_I2C3_SDA_PIN
- int "I2C3 sda pin number"
- range 1 176
- default 33
- endif
- endif
-
- menuconfig BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- select RT_USING_LIBC
- default n
- if BSP_USING_ONCHIP_RTC
- choice
- prompt "Select clock source"
- default BSP_RTC_USING_LSE
- config BSP_RTC_USING_LSE
- bool "RTC USING LSE"
- config BSP_RTC_USING_LSI
- bool "RTC USING LSI"
- endchoice
- endif
-
- source "../libraries/HAL_Drivers/Kconfig"
-
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
