| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175 |
- menu "Hardware Drivers Config"
- config SOC_STM32H743II
- bool
- select SOC_SERIES_STM32H7
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_COM2
- bool "Enable COM2(485)"
- select BSP_USING_UART
- select BSP_USING_UART2
- select BSP_USING_I2C1
- select PKG_USING_PCF8574
- default n
- config BSP_USING_SDRAM
- bool "Enable SDRAM"
- select BSP_USING_FMC
- default n
- config BSP_USING_LCD
- bool "Enable LCD"
- select BSP_USING_LTDC
- select BSP_USING_SDRAM
- default n
- config BSP_USING_QSPI_FLASH
- bool "Enable QSPI FLASH (W25Q256 qspi)"
- select BSP_USING_QSPI
- select RT_USING_SFUD
- select RT_SFUD_USING_QSPI
- default n
- config BSP_USING_SDMMC
- bool "Enable SDMMC (SD card)"
- select RT_USING_SDIO
- select RT_USING_DFS
- select RT_USING_DFS_ELMFAT
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default y
- config BSP_USING_UART2
- bool "Enable UART2"
- default n
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- config BSP_UART2_TX_USING_DMA
- bool "Enable UART2 TX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- endif
- config BSP_USING_FMC
- bool
- default n
- config BSP_USING_LTDC
- bool
- default n
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI2
- bool "Enable SPI2 BUS"
- default n
- endif
- config BSP_USING_QSPI
- bool "Enable QSPI BUS"
- select RT_USING_QSPI
- select RT_USING_SPI
- default n
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- comment "Notice: PH4 --> 116; PH5 --> 117"
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 1 176
- default 116
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 176
- default 117
- endif
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- default n
- menuconfig BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- select RT_USING_LIBC
- default n
- if BSP_USING_ONCHIP_RTC
- choice
- prompt "Select clock source"
- default BSP_RTC_USING_LSE
- config BSP_RTC_USING_LSE
- bool "RTC USING LSE"
- config BSP_RTC_USING_LSI
- bool "RTC USING LSI"
- endchoice
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- menuconfig BSP_USING_DAC
- bool "Enable DAC"
- default n
- select RT_USING_DAC
- if BSP_USING_DAC
- config BSP_USING_DAC1
- bool "Enable DAC1"
- default n
- endif
- config BSP_USING_WDT
- bool "Enable Watchdog Timer"
- select RT_USING_WDT
- default n
- source "../libraries/HAL_Drivers/Kconfig"
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
