rt-thread/bsp/stm32/libraries/HAL_Drivers/drivers/drv_usart_v2.c

/*
 * Copyright (c) 2006-2024 RT-Thread Development Team
 *
 * SPDX-License-Identifier: Apache-2.0
 *
 * Change Logs:
 * Date           Author       Notes
 * 2021-06-01     KyleChan     first version
 */

#include "board.h"
#include "drv_usart_v2.h"

#ifdef RT_USING_SERIAL_V2

// #define DRV_DEBUG
#define DBG_TAG "drv.usart"
#ifdef DRV_DEBUG
#define DBG_LVL DBG_LOG
#else
#define DBG_LVL DBG_INFO
#endif /* DRV_DEBUG */
#include <rtdbg.h>

#if !defined(BSP_USING_UART1) && !defined(BSP_USING_UART2) && !defined(BSP_USING_UART3) && !defined(BSP_USING_UART4) && !defined(BSP_USING_UART5) && !defined(BSP_USING_UART6) && !defined(BSP_USING_UART7) && !defined(BSP_USING_UART8) && !defined(BSP_USING_LPUART1)
#error "Please define at least one BSP_USING_UARTx"
/* this driver can be disabled at menuconfig -> RT-Thread Components -> Device Drivers */
#endif

#ifdef RT_SERIAL_USING_DMA
static void stm32_dma_config(struct rt_serial_device *serial, rt_ubase_t flag);
#endif

enum
{
#ifdef BSP_USING_UART1
    UART1_INDEX,
#endif

#ifdef BSP_USING_UART2
    UART2_INDEX,
#endif

#ifdef BSP_USING_UART3
    UART3_INDEX,
#endif

#ifdef BSP_USING_UART4
    UART4_INDEX,
#endif

#ifdef BSP_USING_UART5
    UART5_INDEX,
#endif

#ifdef BSP_USING_UART6
    UART6_INDEX,
#endif

#ifdef BSP_USING_UART7
    UART7_INDEX,
#endif

#ifdef BSP_USING_UART8
    UART8_INDEX,
#endif

#ifdef BSP_USING_LPUART1
    LPUART1_INDEX,
#endif
};

static struct stm32_uart_config uart_config[] =
    {
#ifdef BSP_USING_UART1
        UART1_CONFIG,
#endif

#ifdef BSP_USING_UART2
        UART2_CONFIG,
#endif

#ifdef BSP_USING_UART3
        UART3_CONFIG,
#endif

#ifdef BSP_USING_UART4
        UART4_CONFIG,
#endif

#ifdef BSP_USING_UART5
        UART5_CONFIG,
#endif

#ifdef BSP_USING_UART6
        UART6_CONFIG,
#endif

#ifdef BSP_USING_UART7
        UART7_CONFIG,
#endif

#ifdef BSP_USING_UART8
        UART8_CONFIG,
#endif

#ifdef BSP_USING_LPUART1
        LPUART1_CONFIG,
#endif
};


static struct stm32_uart uart_obj[sizeof(uart_config) / sizeof(uart_config[0])] = {0};

static rt_err_t stm32_configure(struct rt_serial_device *serial, struct serial_configure *cfg)
{
    struct stm32_uart *uart;
    RT_ASSERT(serial != RT_NULL);
    RT_ASSERT(cfg != RT_NULL);

    uart                       = rt_container_of(serial, struct stm32_uart, serial);
    uart->handle.Instance      = uart->config->Instance;
    uart->handle.Init.BaudRate = cfg->baud_rate;
    uart->handle.Init.Mode     = UART_MODE_TX_RX;
#ifdef USART_CR1_OVER8
    uart->handle.Init.OverSampling = cfg->baud_rate > 5000000 ? UART_OVERSAMPLING_8 : UART_OVERSAMPLING_16;
#else
    uart->handle.Init.OverSampling = UART_OVERSAMPLING_16;
#endif /* USART_CR1_OVER8 */

    switch (cfg->data_bits)
    {
    case DATA_BITS_8:
        if (cfg->parity == PARITY_ODD || cfg->parity == PARITY_EVEN)
            uart->handle.Init.WordLength = UART_WORDLENGTH_9B;
        else
            uart->handle.Init.WordLength = UART_WORDLENGTH_8B;
        break;
    case DATA_BITS_9:
        uart->handle.Init.WordLength = UART_WORDLENGTH_9B;
        break;
    default:
        uart->handle.Init.WordLength = UART_WORDLENGTH_8B;
        break;
    }

    switch (cfg->stop_bits)
    {
    case STOP_BITS_1:
        uart->handle.Init.StopBits = UART_STOPBITS_1;
        break;
    case STOP_BITS_2:
        uart->handle.Init.StopBits = UART_STOPBITS_2;
        break;
    default:
        uart->handle.Init.StopBits = UART_STOPBITS_1;
        break;
    }

    switch (cfg->parity)
    {
    case PARITY_NONE:
        uart->handle.Init.Parity = UART_PARITY_NONE;
        break;
    case PARITY_ODD:
        uart->handle.Init.Parity = UART_PARITY_ODD;
        break;
    case PARITY_EVEN:
        uart->handle.Init.Parity = UART_PARITY_EVEN;
        break;
    default:
        uart->handle.Init.Parity = UART_PARITY_NONE;
        break;
    }

    switch (cfg->flowcontrol)
    {
    case RT_SERIAL_FLOWCONTROL_NONE:
        uart->handle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
        break;
    case RT_SERIAL_FLOWCONTROL_CTSRTS:
        uart->handle.Init.HwFlowCtl = UART_HWCONTROL_RTS_CTS;
        break;
    default:
        uart->handle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
        break;
    }

#ifdef RT_SERIAL_USING_DMA
    uart->dma_rx.remaining_cnt = serial->config.dma_ping_bufsz;
#endif

    if (HAL_UART_Init(&uart->handle) != HAL_OK)
    {
        return -RT_ERROR;
    }

    return RT_EOK;
}

static rt_err_t stm32_control(struct rt_serial_device *serial, int cmd, void *arg)
{
    struct stm32_uart *uart;

    rt_ubase_t ctrl_arg = (rt_ubase_t)arg;

    RT_ASSERT(serial != RT_NULL);
    uart = rt_container_of(serial, struct stm32_uart, serial);

    if (ctrl_arg & (RT_DEVICE_FLAG_RX_BLOCKING | RT_DEVICE_FLAG_RX_NON_BLOCKING))
    {
        if (uart->uart_dma_flag & RT_DEVICE_FLAG_DMA_RX)
            ctrl_arg = RT_DEVICE_FLAG_DMA_RX;
        else
            ctrl_arg = RT_DEVICE_FLAG_INT_RX;
    }
    else if (ctrl_arg & (RT_DEVICE_FLAG_TX_BLOCKING | RT_DEVICE_FLAG_TX_NON_BLOCKING))
    {
        if (uart->uart_dma_flag & RT_DEVICE_FLAG_DMA_TX)
            ctrl_arg = RT_DEVICE_FLAG_DMA_TX;
        else
            ctrl_arg = RT_DEVICE_FLAG_INT_TX;
    }

    switch (cmd)
    {
    /* disable interrupt */
    case RT_DEVICE_CTRL_CLR_INT:

        NVIC_DisableIRQ(uart->config->irq_type);
        if (ctrl_arg == RT_DEVICE_FLAG_INT_RX)
            __HAL_UART_DISABLE_IT(&(uart->handle), UART_IT_RXNE);
        else if (ctrl_arg == RT_DEVICE_FLAG_INT_TX)
            __HAL_UART_DISABLE_IT(&(uart->handle), UART_IT_TXE);
#ifdef RT_SERIAL_USING_DMA
        else if (ctrl_arg == RT_DEVICE_FLAG_DMA_RX)
        {
            __HAL_UART_DISABLE_IT(&(uart->handle), UART_IT_RXNE);

            HAL_NVIC_DisableIRQ(uart->config->dma_rx->dma_irq);
            if (HAL_DMA_Abort(&(uart->dma_rx.handle)) != HAL_OK)
            {
                RT_ASSERT(0);
            }

            if (HAL_DMA_DeInit(&(uart->dma_rx.handle)) != HAL_OK)
            {
                RT_ASSERT(0);
            }
        }
        else if (ctrl_arg == RT_DEVICE_FLAG_DMA_TX)
        {
            __HAL_UART_DISABLE_IT(&(uart->handle), UART_IT_TC);

            HAL_NVIC_DisableIRQ(uart->config->dma_tx->dma_irq);

            HAL_DMA_Abort(&(uart->dma_tx.handle));

            if (HAL_DMA_DeInit(&(uart->dma_tx.handle)) != HAL_OK)
            {
                RT_ASSERT(0);
            }
        }
#endif
        break;

    case RT_DEVICE_CTRL_SET_INT:

        HAL_NVIC_SetPriority(uart->config->irq_type, 1, 0);
        HAL_NVIC_EnableIRQ(uart->config->irq_type);

        if (ctrl_arg == RT_DEVICE_FLAG_INT_RX)
            __HAL_UART_ENABLE_IT(&(uart->handle), UART_IT_RXNE);
        else if (ctrl_arg == RT_DEVICE_FLAG_INT_TX)
            __HAL_UART_ENABLE_IT(&(uart->handle), UART_IT_TXE);
        break;

    case RT_DEVICE_CTRL_CONFIG:
        if (ctrl_arg & (RT_DEVICE_FLAG_DMA_RX | RT_DEVICE_FLAG_DMA_TX))
        {
#ifdef RT_SERIAL_USING_DMA
            stm32_dma_config(serial, ctrl_arg);
#endif
        }
        else
            stm32_control(serial, RT_DEVICE_CTRL_SET_INT, (void *)ctrl_arg);
        break;

    case RT_DEVICE_CHECK_OPTMODE: {
        if (ctrl_arg & RT_DEVICE_FLAG_DMA_TX)
            return RT_SERIAL_TX_BLOCKING_NO_BUFFER;
        else
            return RT_SERIAL_TX_BLOCKING_BUFFER;
    }
    case RT_DEVICE_CTRL_CLOSE:
        if (HAL_UART_DeInit(&(uart->handle)) != HAL_OK)
        {
            RT_ASSERT(0)
        }
        break;
    }
    return RT_EOK;
}

static int stm32_putc(struct rt_serial_device *serial, char c)
{
    struct stm32_uart *uart;
    RT_ASSERT(serial != RT_NULL);

    uart = rt_container_of(serial, struct stm32_uart, serial);
    UART_INSTANCE_CLEAR_FUNCTION(&(uart->handle), UART_FLAG_TC);
    UART_SET_TDR(&uart->handle, c);
    while (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_TC) == RESET);

    return 1;
}

rt_uint32_t stm32_uart_get_mask(rt_uint32_t word_length, rt_uint32_t parity)
{
    rt_uint32_t mask = 0;
    if (word_length == UART_WORDLENGTH_8B)
    {
        if (parity == UART_PARITY_NONE)
        {
            mask = 0x00FFU;
        }
        else
        {
            mask = 0x007FU;
        }
    }
#ifdef UART_WORDLENGTH_9B
    else if (word_length == UART_WORDLENGTH_9B)
    {
        if (parity == UART_PARITY_NONE)
        {
            mask = 0x01FFU;
        }
        else
        {
            mask = 0x00FFU;
        }
    }
#endif
#ifdef UART_WORDLENGTH_7B
    else if (word_length == UART_WORDLENGTH_7B)
    {
        if (parity == UART_PARITY_NONE)
        {
            mask = 0x007FU;
        }
        else
        {
            mask = 0x003FU;
        }
    }
    else
    {
        mask = 0x0000U;
    }
#endif
    return mask;
}

static int stm32_getc(struct rt_serial_device *serial)
{
    int                ch;
    struct stm32_uart *uart;
    RT_ASSERT(serial != RT_NULL);
    uart = rt_container_of(serial, struct stm32_uart, serial);

    ch = -1;
    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_RXNE) != RESET)
        ch = UART_GET_RDR(&uart->handle, stm32_uart_get_mask(uart->handle.Init.WordLength, uart->handle.Init.Parity));
    return ch;
}

static rt_ssize_t stm32_transmit(struct rt_serial_device *serial,
                                 rt_uint8_t              *buf,
                                 rt_size_t                size,
                                 rt_uint32_t              tx_flag)
{
    struct stm32_uart *uart;

    RT_ASSERT(serial != RT_NULL);
    RT_ASSERT(buf != RT_NULL);
    uart = rt_container_of(serial, struct stm32_uart, serial);

    if (uart->uart_dma_flag & RT_DEVICE_FLAG_DMA_TX)
    {
        if (HAL_UART_Transmit_DMA(&uart->handle, buf, size) != HAL_OK)
        {
            return -RT_EIO;
        }

        return size;
    }

    /* NOLINTNEXTLINE(performance-no-int-to-ptr) */
    if (stm32_control(serial, RT_DEVICE_CTRL_SET_INT, (void *)tx_flag) != RT_EOK)
    {
        return -RT_EIO;
    }

    return size;
}

#ifdef RT_SERIAL_USING_DMA
static void dma_recv_isr(struct rt_serial_device *serial, rt_uint8_t isr_flag)
{
    struct stm32_uart *uart;
    rt_size_t          recv_len, counter;

    RT_ASSERT(serial != RT_NULL);
    uart = rt_container_of(serial, struct stm32_uart, serial);

    counter = __HAL_DMA_GET_COUNTER(&(uart->dma_rx.handle));

    if (counter <= uart->dma_rx.remaining_cnt)
        recv_len = uart->dma_rx.remaining_cnt - counter;
    else
        recv_len = serial->config.dma_ping_bufsz + uart->dma_rx.remaining_cnt - counter;
    if (recv_len)
    {
#if defined(__DCACHE_PRESENT) && (__DCACHE_PRESENT == 1U)
        rt_uint8_t *ptr = NULL;
        rt_hw_serial_control_isr(serial, RT_HW_SERIAL_CTRL_GET_DMA_PING_BUF, (void *)&ptr);
        SCB_InvalidateDCache_by_Addr((uint32_t *)ptr, serial->config.dma_ping_bufsz);
#endif
        uart->dma_rx.remaining_cnt = counter;
        rt_hw_serial_isr(serial, RT_SERIAL_EVENT_RX_DMADONE | (recv_len << 8));
    }
}
#endif /* RT_SERIAL_USING_DMA */

/**
 * Uart common interrupt process. This need add to uart ISR.
 *
 * @param serial serial device
 */
static void uart_isr(struct rt_serial_device *serial)
{
    struct stm32_uart *uart;

    RT_ASSERT(serial != RT_NULL);
    uart = rt_container_of(serial, struct stm32_uart, serial);
    /* If the Read data register is not empty and the RXNE interrupt is enabled  (RDR) */
    if ((__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_RXNE)) && (__HAL_UART_GET_IT_SOURCE(&(uart->handle), UART_IT_RXNE)))
    {
        rt_uint8_t  chr;
        rt_uint32_t rx_drain_limit = 1024;
        rt_uint32_t mask           = stm32_uart_get_mask(uart->handle.Init.WordLength, uart->handle.Init.Parity);
        do {
            chr = UART_GET_RDR(&uart->handle, mask);
            rt_hw_serial_control_isr(serial, RT_HW_SERIAL_CTRL_PUTC, (void *)&chr);
            rt_hw_serial_isr(serial, RT_SERIAL_EVENT_RX_IND);
            rx_drain_limit--;
        } while (__HAL_UART_GET_FLAG(&uart->handle, UART_FLAG_RXNE) && rx_drain_limit > 0);
    }
    /* If the Transmit data register is empty and the TXE interrupt enable is enabled  (TDR) */
    if ((__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_TXE)) && (__HAL_UART_GET_IT_SOURCE(&(uart->handle), UART_IT_TXE)))
    {
        rt_uint8_t put_char = 0;
        if (rt_hw_serial_control_isr(serial, RT_HW_SERIAL_CTRL_GETC, (void *)&put_char) == RT_EOK)
        {
            UART_SET_TDR(&uart->handle, put_char);
        }
        else
        {
            __HAL_UART_DISABLE_IT(&(uart->handle), UART_IT_TXE);
            __HAL_UART_ENABLE_IT(&(uart->handle), UART_IT_TC);
        }
    }
    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_TC) && (__HAL_UART_GET_IT_SOURCE(&(uart->handle), UART_IT_TC)))
    {
        if (uart->uart_dma_flag & RT_DEVICE_FLAG_DMA_TX)
        {
            /* The HAL_UART_TxCpltCallback will be triggered */
            HAL_UART_IRQHandler(&(uart->handle));
        }
        else
        {
            /* Transmission complete interrupt disable ( CR1 Register) */
            __HAL_UART_DISABLE_IT(&(uart->handle), UART_IT_TC);
            rt_hw_serial_isr(serial, RT_SERIAL_EVENT_TX_DONE);
            /* Clear Transmission complete interrupt flag ( ISR Register ) */
            UART_INSTANCE_CLEAR_FUNCTION(&(uart->handle), UART_FLAG_TC);
        }
    }

#ifdef RT_SERIAL_USING_DMA
    if ((uart->uart_dma_flag) && (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_IDLE))
        && (__HAL_UART_GET_IT_SOURCE(&(uart->handle), UART_IT_IDLE)))
    {
        dma_recv_isr(serial, UART_RX_DMA_IT_IDLE_FLAG);
        __HAL_UART_CLEAR_IDLEFLAG(&uart->handle);
    }
#endif

    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_ORE))
    {
        LOG_E("(%s) serial device Overrun error!", serial->parent.parent.name);
        __HAL_UART_CLEAR_OREFLAG(&uart->handle);
    }
    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_NE))
    {
        __HAL_UART_CLEAR_NEFLAG(&uart->handle);
    }
    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_FE))
    {
        __HAL_UART_CLEAR_FEFLAG(&uart->handle);
    }
    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_PE))
    {
        __HAL_UART_CLEAR_PEFLAG(&uart->handle);
    }
#if !defined(SOC_SERIES_STM32L4) && !defined(SOC_SERIES_STM32WL) && !defined(SOC_SERIES_STM32F7) && !defined(SOC_SERIES_STM32F0) \
    && !defined(SOC_SERIES_STM32L0) && !defined(SOC_SERIES_STM32G0) && !defined(SOC_SERIES_STM32H7)                              \
    && !defined(SOC_SERIES_STM32G4) && !defined(SOC_SERIES_STM32MP1) && !defined(SOC_SERIES_STM32WB)                             \
    && !defined(SOC_SERIES_STM32L5) && !defined(SOC_SERIES_STM32U5) && !defined(SOC_SERIES_STM32H5) && !defined(SOC_SERIES_STM32H7RS)
#ifdef SOC_SERIES_STM32F3
    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_LBDF))
    {
        UART_INSTANCE_CLEAR_FUNCTION(&(uart->handle), UART_FLAG_LBDF);
    }
#else
    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_LBD))
    {
        UART_INSTANCE_CLEAR_FUNCTION(&(uart->handle), UART_FLAG_LBD);
    }
#endif
#endif
    if (__HAL_UART_GET_FLAG(&(uart->handle), UART_FLAG_CTS))
    {
        UART_INSTANCE_CLEAR_FUNCTION(&(uart->handle), UART_FLAG_CTS);
    }
}

#if defined(BSP_USING_UART1)
void USART1_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[UART1_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART1_RX_USING_DMA)
void UART1_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART1_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART1_RX_USING_DMA) */
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART1_TX_USING_DMA)
void UART1_DMA_TX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART1_INDEX].dma_tx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART1_TX_USING_DMA) */
#endif /* BSP_USING_UART1 */

#if defined(BSP_USING_UART2)
void USART2_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[UART2_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART2_RX_USING_DMA)
void UART2_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART2_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART2_RX_USING_DMA) */
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART2_TX_USING_DMA)
void UART2_DMA_TX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART2_INDEX].dma_tx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART2_TX_USING_DMA) */
#endif /* BSP_USING_UART2 */

#if defined(BSP_USING_UART3)
void USART3_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[UART3_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART3_RX_USING_DMA)
void UART3_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART3_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(BSP_UART_USING_DMA_RX) && defined(BSP_UART3_RX_USING_DMA) */
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART3_TX_USING_DMA)
void UART3_DMA_TX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART3_INDEX].dma_tx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(BSP_UART_USING_DMA_TX) && defined(BSP_UART3_TX_USING_DMA) */
#endif /* BSP_USING_UART3*/

#if defined(BSP_USING_UART4)
void UART4_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[UART4_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART4_RX_USING_DMA)
void UART4_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART4_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(BSP_UART_USING_DMA_RX) && defined(BSP_UART4_RX_USING_DMA) */

#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART4_TX_USING_DMA)
void UART4_DMA_TX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART4_INDEX].dma_tx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(BSP_UART_USING_DMA_TX) && defined(BSP_UART4_TX_USING_DMA) */
#endif /* BSP_USING_UART4*/

#if defined(BSP_USING_UART5)
void UART5_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[UART5_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART5_RX_USING_DMA)
void UART5_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART5_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART5_RX_USING_DMA) */
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART5_TX_USING_DMA)
void UART5_DMA_TX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART5_INDEX].dma_tx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART5_TX_USING_DMA) */
#endif /* BSP_USING_UART5*/

#if defined(BSP_USING_UART6)
void USART6_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[UART6_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART6_RX_USING_DMA)
void UART6_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART6_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART6_RX_USING_DMA) */
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART6_TX_USING_DMA)
void UART6_DMA_TX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART6_INDEX].dma_tx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART6_TX_USING_DMA) */
#endif /* BSP_USING_UART6*/

#if defined(BSP_USING_UART7)
void UART7_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[UART7_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART7_RX_USING_DMA)
void UART7_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART7_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART7_RX_USING_DMA) */
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART7_TX_USING_DMA)
void UART7_DMA_TX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART7_INDEX].dma_tx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART7_TX_USING_DMA) */
#endif /* BSP_USING_UART7*/

#if defined(BSP_USING_UART8)
void UART8_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[UART8_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART8_RX_USING_DMA)
void UART8_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART8_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART8_RX_USING_DMA) */
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_UART8_TX_USING_DMA)
void UART8_DMA_TX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[UART8_INDEX].dma_tx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_UART8_TX_USING_DMA) */
#endif /* BSP_USING_UART8*/

#if defined(BSP_USING_LPUART1)
void LPUART1_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    uart_isr(&(uart_obj[LPUART1_INDEX].serial));

    /* leave interrupt */
    rt_interrupt_leave();
}
#if defined(RT_SERIAL_USING_DMA) && defined(BSP_LPUART1_RX_USING_DMA)
void LPUART1_DMA_RX_IRQHandler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    HAL_DMA_IRQHandler(&uart_obj[LPUART1_INDEX].dma_rx.handle);

    /* leave interrupt */
    rt_interrupt_leave();
}
#endif /* defined(RT_SERIAL_USING_DMA) && defined(BSP_LPUART1_RX_USING_DMA) */
#endif /* BSP_USING_LPUART1*/

#if defined(SOC_SERIES_STM32G0)
#if defined(BSP_USING_UART2)
#if defined(STM32G0B1xx) || defined(STM32G0C1xx)
void USART2_LPUART2_IRQHandler(void)
{
    USART2_IRQHandler();
}
#endif /* defined(STM32G0B1xx) || defined(STM32G0C1xx) */
#endif /* defined(BSP_USING_UART2) */
#if defined(BSP_USING_UART3) || defined(BSP_USING_UART4) || defined(BSP_USING_UART5) || defined(BSP_USING_UART6) \
    || defined(BSP_USING_LPUART1)
#if defined(STM32G070xx)
void USART3_4_IRQHandler(void)
#elif defined(STM32G071xx) || defined(STM32G081xx)
void USART3_4_LPUART1_IRQHandler(void)
#elif defined(STM32G0B0xx)
void USART3_4_5_6_IRQHandler(void)
#elif defined(STM32G0B1xx) || defined(STM32G0C1xx)
void USART3_4_5_6_LPUART1_IRQHandler(void)
#endif /* defined(STM32G070xx) */
{
#if defined(BSP_USING_UART3)
    USART3_IRQHandler();
#endif
#if defined(BSP_USING_UART4)
    UART4_IRQHandler();
#endif
#if defined(BSP_USING_UART5)
    UART5_IRQHandler();
#endif
#if defined(BSP_USING_UART6)
    USART6_IRQHandler();
#endif
#if defined(BSP_USING_LPUART1)
    LPUART1_IRQHandler();
#endif
}
#endif /* defined(BSP_USING_UART3) || defined(BSP_USING_UART4) || defined(BSP_USING_UART5) || defined(BSP_USING_UART6) */
#if defined(RT_SERIAL_USING_DMA)
void UART_DMA_RX_TX_IRQHandler(void)
{
#if defined(BSP_USING_UART1) && defined(BSP_UART1_TX_USING_DMA)
    UART1_DMA_TX_IRQHandler();
#endif
#if defined(BSP_USING_UART1) && defined(BSP_UART1_RX_USING_DMA)
    UART1_DMA_RX_IRQHandler();
#endif
#if defined(BSP_USING_UART2) && defined(BSP_UART2_TX_USING_DMA)
    UART2_DMA_TX_IRQHandler();
#endif
#if defined(BSP_USING_UART2) && defined(BSP_UART2_RX_USING_DMA)
    UART2_DMA_RX_IRQHandler();
#endif
}
#endif /* defined(RT_SERIAL_USING_DMA) */
#endif /* defined(SOC_SERIES_STM32G0) */

static void stm32_uart_get_config(void)
{
    struct serial_configure config = RT_SERIAL_CONFIG_DEFAULT;
#ifdef BSP_USING_UART1
    uart_obj[UART1_INDEX].serial.config = config;
    uart_obj[UART1_INDEX].uart_dma_flag = 0;

    uart_obj[UART1_INDEX].serial.config.rx_bufsz = BSP_UART1_RX_BUFSIZE;
    uart_obj[UART1_INDEX].serial.config.tx_bufsz = BSP_UART1_TX_BUFSIZE;

#ifdef BSP_UART1_RX_USING_DMA
    uart_obj[UART1_INDEX].serial.config.dma_ping_bufsz  = BSP_UART1_DMA_PING_BUFSIZE;
    uart_obj[UART1_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config uart1_dma_rx               = UART1_DMA_RX_CONFIG;
    uart_config[UART1_INDEX].dma_rx                     = &uart1_dma_rx;
#endif

#ifdef BSP_UART1_TX_USING_DMA
    uart_obj[UART1_INDEX].uart_dma_flag   |= RT_DEVICE_FLAG_DMA_TX;
    static struct dma_config uart1_dma_tx  = UART1_DMA_TX_CONFIG;
    uart_config[UART1_INDEX].dma_tx        = &uart1_dma_tx;
#endif
#endif

#ifdef BSP_USING_UART2
    uart_obj[UART2_INDEX].serial.config = config;
    uart_obj[UART2_INDEX].uart_dma_flag = 0;

    uart_obj[UART2_INDEX].serial.config.rx_bufsz = BSP_UART2_RX_BUFSIZE;
    uart_obj[UART2_INDEX].serial.config.tx_bufsz = BSP_UART2_TX_BUFSIZE;

#ifdef BSP_UART2_RX_USING_DMA
    uart_obj[UART2_INDEX].serial.config.dma_ping_bufsz  = BSP_UART2_DMA_PING_BUFSIZE;
    uart_obj[UART2_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config uart2_dma_rx               = UART2_DMA_RX_CONFIG;
    uart_config[UART2_INDEX].dma_rx                     = &uart2_dma_rx;
#endif

#ifdef BSP_UART2_TX_USING_DMA
    uart_obj[UART2_INDEX].uart_dma_flag   |= RT_DEVICE_FLAG_DMA_TX;
    static struct dma_config uart2_dma_tx  = UART2_DMA_TX_CONFIG;
    uart_config[UART2_INDEX].dma_tx        = &uart2_dma_tx;
#endif
#endif

#ifdef BSP_USING_UART3
    uart_obj[UART3_INDEX].serial.config = config;
    uart_obj[UART3_INDEX].uart_dma_flag = 0;

    uart_obj[UART3_INDEX].serial.config.rx_bufsz = BSP_UART3_RX_BUFSIZE;
    uart_obj[UART3_INDEX].serial.config.tx_bufsz = BSP_UART3_TX_BUFSIZE;

#ifdef BSP_UART3_RX_USING_DMA
    uart_obj[UART3_INDEX].serial.config.dma_ping_bufsz  = BSP_UART3_DMA_PING_BUFSIZE;
    uart_obj[UART3_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config uart3_dma_rx               = UART3_DMA_RX_CONFIG;
    uart_config[UART3_INDEX].dma_rx                     = &uart3_dma_rx;
#endif

#ifdef BSP_UART3_TX_USING_DMA
    uart_obj[UART3_INDEX].uart_dma_flag   |= RT_DEVICE_FLAG_DMA_TX;
    static struct dma_config uart3_dma_tx  = UART3_DMA_TX_CONFIG;
    uart_config[UART3_INDEX].dma_tx        = &uart3_dma_tx;
#endif
#endif

#ifdef BSP_USING_UART4
    uart_obj[UART4_INDEX].serial.config = config;
    uart_obj[UART4_INDEX].uart_dma_flag = 0;

    uart_obj[UART4_INDEX].serial.config.rx_bufsz = BSP_UART4_RX_BUFSIZE;
    uart_obj[UART4_INDEX].serial.config.tx_bufsz = BSP_UART4_TX_BUFSIZE;

#ifdef BSP_UART4_RX_USING_DMA
    uart_obj[UART4_INDEX].serial.config.dma_ping_bufsz  = BSP_UART4_DMA_PING_BUFSIZE;
    uart_obj[UART4_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config uart4_dma_rx               = UART4_DMA_RX_CONFIG;
    uart_config[UART4_INDEX].dma_rx                     = &uart4_dma_rx;
#endif

#ifdef BSP_UART4_TX_USING_DMA
    uart_obj[UART4_INDEX].uart_dma_flag   |= RT_DEVICE_FLAG_DMA_TX;
    static struct dma_config uart4_dma_tx  = UART4_DMA_TX_CONFIG;
    uart_config[UART4_INDEX].dma_tx        = &uart4_dma_tx;
#endif
#endif

#ifdef BSP_USING_UART5
    uart_obj[UART5_INDEX].serial.config = config;
    uart_obj[UART5_INDEX].uart_dma_flag = 0;

    uart_obj[UART5_INDEX].serial.config.rx_bufsz = BSP_UART5_RX_BUFSIZE;
    uart_obj[UART5_INDEX].serial.config.tx_bufsz = BSP_UART5_TX_BUFSIZE;

#ifdef BSP_UART5_RX_USING_DMA
    uart_obj[UART5_INDEX].serial.config.dma_ping_bufsz  = BSP_UART5_DMA_PING_BUFSIZE;
    uart_obj[UART5_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config uart5_dma_rx               = UART5_DMA_RX_CONFIG;
    uart_config[UART5_INDEX].dma_rx                     = &uart5_dma_rx;
#endif

#ifdef BSP_UART5_TX_USING_DMA
    uart_obj[UART5_INDEX].uart_dma_flag   |= RT_DEVICE_FLAG_DMA_TX;
    static struct dma_config uart5_dma_tx  = UART5_DMA_TX_CONFIG;
    uart_config[UART5_INDEX].dma_tx        = &uart5_dma_tx;
#endif
#endif

#ifdef BSP_USING_UART6
    uart_obj[UART6_INDEX].serial.config = config;
    uart_obj[UART6_INDEX].uart_dma_flag = 0;

    uart_obj[UART6_INDEX].serial.config.rx_bufsz = BSP_UART6_RX_BUFSIZE;
    uart_obj[UART6_INDEX].serial.config.tx_bufsz = BSP_UART6_TX_BUFSIZE;

#ifdef BSP_UART6_RX_USING_DMA
    uart_obj[UART6_INDEX].serial.config.dma_ping_bufsz  = BSP_UART6_DMA_PING_BUFSIZE;
    uart_obj[UART6_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config uart6_dma_rx               = UART6_DMA_RX_CONFIG;
    uart_config[UART6_INDEX].dma_rx                     = &uart6_dma_rx;
#endif

#ifdef BSP_UART6_TX_USING_DMA
    uart_obj[UART6_INDEX].uart_dma_flag   |= RT_DEVICE_FLAG_DMA_TX;
    static struct dma_config uart6_dma_tx  = UART6_DMA_TX_CONFIG;
    uart_config[UART6_INDEX].dma_tx        = &uart6_dma_tx;
#endif
#endif

#ifdef BSP_USING_UART7
    uart_obj[UART7_INDEX].serial.config = config;
    uart_obj[UART7_INDEX].uart_dma_flag = 0;

    uart_obj[UART7_INDEX].serial.config.rx_bufsz = BSP_UART7_RX_BUFSIZE;
    uart_obj[UART7_INDEX].serial.config.tx_bufsz = BSP_UART7_TX_BUFSIZE;

#ifdef BSP_UART7_RX_USING_DMA
    uart_obj[UART7_INDEX].serial.config.dma_ping_bufsz  = BSP_UART7_DMA_PING_BUFSIZE;
    uart_obj[UART7_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config uart7_dma_rx               = UART7_DMA_RX_CONFIG;
    uart_config[UART7_INDEX].dma_rx                     = &uart7_dma_rx;
#endif

#ifdef BSP_UART7_TX_USING_DMA
    uart_obj[UART7_INDEX].uart_dma_flag   |= RT_DEVICE_FLAG_DMA_TX;
    static struct dma_config uart7_dma_tx  = UART7_DMA_TX_CONFIG;
    uart_config[UART7_INDEX].dma_tx        = &uart7_dma_tx;
#endif
#endif

#ifdef BSP_USING_UART8
    uart_obj[UART8_INDEX].serial.config = config;
    uart_obj[UART8_INDEX].uart_dma_flag = 0;

    uart_obj[UART8_INDEX].serial.config.rx_bufsz = BSP_UART8_RX_BUFSIZE;
    uart_obj[UART8_INDEX].serial.config.tx_bufsz = BSP_UART8_TX_BUFSIZE;

#ifdef BSP_UART8_RX_USING_DMA
    uart_obj[UART8_INDEX].uart_dma_flag   |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config uart8_dma_rx  = UART8_DMA_RX_CONFIG;
    uart_config[UART8_INDEX].dma_rx        = &uart8_dma_rx;
#endif

#ifdef BSP_UART8_TX_USING_DMA
    uart_obj[UART8_INDEX].serial.config.dma_ping_bufsz  = BSP_UART8_DMA_PING_BUFSIZE;
    uart_obj[UART8_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_TX;
    static struct dma_config uart8_dma_tx               = UART8_DMA_TX_CONFIG;
    uart_config[UART8_INDEX].dma_tx                     = &uart8_dma_tx;
#endif
#endif

#ifdef BSP_USING_LPUART1
    uart_obj[LPUART1_INDEX].serial.config = config;
    uart_obj[LPUART1_INDEX].uart_dma_flag = 0;

    uart_obj[LPUART1_INDEX].serial.config.rx_bufsz = BSP_LPUART1_RX_BUFSIZE;
    uart_obj[LPUART1_INDEX].serial.config.tx_bufsz = BSP_LPUART1_TX_BUFSIZE;

#ifdef BSP_LPUART1_RX_USING_DMA
    uart_obj[LPUART1_INDEX].serial.config.dma_ping_bufsz  = BSP_LPUART1_DMA_PING_BUFSIZE;
    uart_obj[LPUART1_INDEX].uart_dma_flag                |= RT_DEVICE_FLAG_DMA_RX;
    static struct dma_config lpuart1_dma_rx               = LPUART1_DMA_CONFIG;
    uart_config[LPUART1_INDEX].dma_rx                     = &lpuart1_dma_rx;
#endif
#endif
}

#ifdef RT_SERIAL_USING_DMA
static void stm32_dma_config(struct rt_serial_device *serial, rt_ubase_t flag)
{
    DMA_HandleTypeDef *DMA_Handle;
    struct dma_config *dma_config;
    struct stm32_uart *uart;

    RT_ASSERT(serial != RT_NULL);
    RT_ASSERT(flag == RT_DEVICE_FLAG_DMA_TX || flag == RT_DEVICE_FLAG_DMA_RX);
    uart = rt_container_of(serial, struct stm32_uart, serial);

    if (RT_DEVICE_FLAG_DMA_RX == flag)
    {
        DMA_Handle = &uart->dma_rx.handle;
        dma_config = uart->config->dma_rx;
    }
    else /* RT_DEVICE_FLAG_DMA_TX == flag */
    {
        DMA_Handle = &uart->dma_tx.handle;
        dma_config = uart->config->dma_tx;
    }
    LOG_D("%s dma config start", uart->config->name);

    {
        rt_uint32_t tmpreg = 0x00U;
#if defined(SOC_SERIES_STM32F1) || defined(SOC_SERIES_STM32F0) || defined(SOC_SERIES_STM32G0) \
    || defined(SOC_SERIES_STM32L0)
        /* enable DMA clock && Delay after an RCC peripheral clock enabling*/
        SET_BIT(RCC->AHBENR, dma_config->dma_rcc);
        tmpreg = READ_BIT(RCC->AHBENR, dma_config->dma_rcc);
#elif defined(SOC_SERIES_STM32F2) || defined(SOC_SERIES_STM32F4) || defined(SOC_SERIES_STM32F7) || defined(SOC_SERIES_STM32L4) || defined(SOC_SERIES_STM32WL) \
    || defined(SOC_SERIES_STM32G4) || defined(SOC_SERIES_STM32H7) || defined(SOC_SERIES_STM32WB)
        /* enable DMA clock && Delay after an RCC peripheral clock enabling*/
        SET_BIT(RCC->AHB1ENR, dma_config->dma_rcc);
        tmpreg = READ_BIT(RCC->AHB1ENR, dma_config->dma_rcc);
#elif defined(SOC_SERIES_STM32MP1)
        /* enable DMA clock && Delay after an RCC peripheral clock enabling*/
        SET_BIT(RCC->MP_AHB2ENSETR, dma_config->dma_rcc);
        tmpreg = READ_BIT(RCC->MP_AHB2ENSETR, dma_config->dma_rcc);
#endif

#if defined(DMAMUX1) && (defined(SOC_SERIES_STM32L4) || defined(SOC_SERIES_STM32WL) || defined(SOC_SERIES_STM32G4) || defined(SOC_SERIES_STM32WB))
        /* enable DMAMUX clock for L4+ and G4 */
        __HAL_RCC_DMAMUX1_CLK_ENABLE();
#elif defined(SOC_SERIES_STM32MP1)
        __HAL_RCC_DMAMUX_CLK_ENABLE();
#endif

        UNUSED(tmpreg); /* To avoid compiler warnings */
    }

    if (RT_DEVICE_FLAG_DMA_RX == flag)
    {
        __HAL_LINKDMA(&(uart->handle), hdmarx, uart->dma_rx.handle);
    }
    else if (RT_DEVICE_FLAG_DMA_TX == flag)
    {
        __HAL_LINKDMA(&(uart->handle), hdmatx, uart->dma_tx.handle);
    }

#if defined(SOC_SERIES_STM32F1) || defined(SOC_SERIES_STM32F0) || defined(SOC_SERIES_STM32L0) || defined(SOC_SERIES_STM32F3) || defined(SOC_SERIES_STM32L1) || defined(SOC_SERIES_STM32U5) || defined(SOC_SERIES_STM32H5)
    DMA_Handle->Instance = dma_config->Instance;
#elif defined(SOC_SERIES_STM32F2) || defined(SOC_SERIES_STM32F4) || defined(SOC_SERIES_STM32F7)
    DMA_Handle->Instance     = dma_config->Instance;
    DMA_Handle->Init.Channel = dma_config->channel;
#elif defined(SOC_SERIES_STM32L4) || defined(SOC_SERIES_STM32WL) || defined(SOC_SERIES_STM32G0) || defined(SOC_SERIES_STM32G4) || defined(SOC_SERIES_STM32WB) \
    || defined(SOC_SERIES_STM32H7) || defined(SOC_SERIES_STM32MP1)
    DMA_Handle->Instance     = dma_config->Instance;
    DMA_Handle->Init.Request = dma_config->request;
#endif
    DMA_Handle->Init.PeriphInc           = DMA_PINC_DISABLE;
    DMA_Handle->Init.MemInc              = DMA_MINC_ENABLE;
    DMA_Handle->Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
    DMA_Handle->Init.MemDataAlignment    = DMA_MDATAALIGN_BYTE;

    if (RT_DEVICE_FLAG_DMA_RX == flag)
    {
        DMA_Handle->Init.Direction = DMA_PERIPH_TO_MEMORY;
        DMA_Handle->Init.Mode      = DMA_CIRCULAR;
    }
    else if (RT_DEVICE_FLAG_DMA_TX == flag)
    {
        DMA_Handle->Init.Direction = DMA_MEMORY_TO_PERIPH;
        DMA_Handle->Init.Mode      = DMA_NORMAL;
    }

    DMA_Handle->Init.Priority = DMA_PRIORITY_MEDIUM;
#if defined(SOC_SERIES_STM32F2) || defined(SOC_SERIES_STM32F4) || defined(SOC_SERIES_STM32F7) || defined(SOC_SERIES_STM32H7) || defined(SOC_SERIES_STM32MP1)
    DMA_Handle->Init.FIFOMode = DMA_FIFOMODE_DISABLE;
#endif
    if (HAL_DMA_DeInit(DMA_Handle) != HAL_OK)
    {
        RT_ASSERT(0);
    }

    if (HAL_DMA_Init(DMA_Handle) != HAL_OK)
    {
        RT_ASSERT(0);
    }

    /* enable interrupt */
    if (flag == RT_DEVICE_FLAG_DMA_RX)
    {
        rt_uint8_t *ptr = NULL;
        rt_hw_serial_control_isr(serial, RT_HW_SERIAL_CTRL_GET_DMA_PING_BUF, (void *)&ptr);

        /* Start DMA transfer */
        if (HAL_UART_Receive_DMA(&(uart->handle), ptr, serial->config.dma_ping_bufsz) != HAL_OK)
        {
            /* Transfer error in reception process */
            RT_ASSERT(0);
        }
        CLEAR_BIT(uart->handle.Instance->CR3, USART_CR3_EIE);
        __HAL_UART_ENABLE_IT(&(uart->handle), UART_IT_IDLE);
    }

    /* DMA irq should set in DMA TX mode, or HAL_UART_TxCpltCallback function will not be called */
    HAL_NVIC_SetPriority(dma_config->dma_irq, 0, 0);
    HAL_NVIC_EnableIRQ(dma_config->dma_irq);

    HAL_NVIC_SetPriority(uart->config->irq_type, 1, 0);
    HAL_NVIC_EnableIRQ(uart->config->irq_type);

    LOG_D("%s dma %s instance: %x", uart->config->name, flag == RT_DEVICE_FLAG_DMA_RX ? "RX" : "TX", DMA_Handle->Instance);
    LOG_D("%s dma config done", uart->config->name);
}

/**
  * @brief  UART error callbacks
  * @param  huart: UART handle
  * @note   This example shows a simple way to report transfer error, and you can
  *         add your own implementation.
  * @retval None
  */
void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart)
{
    RT_ASSERT(huart != NULL);
    struct stm32_uart *uart = (struct stm32_uart *)huart;
    LOG_D("%s: %s %d\n", __FUNCTION__, uart->config->name, huart->ErrorCode);
    UNUSED(uart);
}

/**
  * @brief  Rx Transfer completed callback
  * @param  huart: UART handle
  * @note   This example shows a simple way to report end of DMA Rx transfer, and
  *         you can add your own implementation.
  * @retval None
  */
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)
{
    struct stm32_uart *uart;
    RT_ASSERT(huart != NULL);
    uart = (struct stm32_uart *)huart;
    dma_recv_isr(&uart->serial, UART_RX_DMA_IT_TC_FLAG);
}

/**
  * @brief  Rx Half transfer completed callback
  * @param  huart: UART handle
  * @note   This example shows a simple way to report end of DMA Rx Half transfer,
  *         and you can add your own implementation.
  * @retval None
  */
void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart)
{
    struct stm32_uart *uart;
    RT_ASSERT(huart != NULL);
    uart = (struct stm32_uart *)huart;
    dma_recv_isr(&uart->serial, UART_RX_DMA_IT_HT_FLAG);
}

/**
  * @brief  HAL_UART_TxCpltCallback
  * @param  huart: UART handle
  * @note   This callback can be called by two functions, first in UART_EndTransmit_IT when
  *         UART Tx complete and second in UART_DMATransmitCplt function in DMA Circular mode.
  * @retval None
  */
void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart)
{
    struct stm32_uart       *uart;
    struct rt_serial_device *serial;
    rt_size_t                trans_total_index;
    rt_base_t                level;

    RT_ASSERT(huart != NULL);
    uart   = (struct stm32_uart *)huart;
    serial = &uart->serial;
    RT_ASSERT(serial != RT_NULL);

    level             = rt_hw_interrupt_disable();
    trans_total_index = __HAL_DMA_GET_COUNTER(&(uart->dma_tx.handle));
    rt_hw_interrupt_enable(level);

    if (trans_total_index) return;

    rt_hw_serial_isr(serial, RT_SERIAL_EVENT_TX_DMADONE);
}
#endif /* RT_SERIAL_USING_DMA */

static const struct rt_uart_ops stm32_uart_ops =
    {
        .configure = stm32_configure,
        .control   = stm32_control,
        .putc      = stm32_putc,
        .getc      = stm32_getc,
        .transmit  = stm32_transmit};

int rt_hw_usart_init(void)
{
    rt_err_t  result  = 0;
    rt_size_t obj_num = sizeof(uart_obj) / sizeof(struct stm32_uart);

    stm32_uart_get_config();
    for (rt_uint32_t i = 0; i < obj_num; i++)
    {
        /* init UART object */
        uart_obj[i].config     = &uart_config[i];
        uart_obj[i].serial.ops = &stm32_uart_ops;
        /* register UART device */
        result = rt_hw_serial_register(&uart_obj[i].serial,
                                       uart_obj[i].config->name,
                                       RT_DEVICE_FLAG_RDWR,
                                       NULL);
        RT_ASSERT(result == RT_EOK);
    }

    return result;
}

#endif /* RT_USING_SERIAL_V2 */