| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297 |
- menu "Hardware Drivers Config"
- menu "Onboard Peripheral Drivers"
- config BSP_USING_USB_TO_USART
- bool "Enable USB TO USART (uart3)"
- select BSP_USING_UART3
- default y
- config BSP_USING_ETH
- bool "Enable Ethernet"
- select RT_USING_LWIP
- default n
- if BSP_USING_ETH
- choice
- prompt "On-board PHY chip"
- default PHY_USING_LAN8742A
- config PHY_USING_LAN8720A
- bool "LAN8720A"
- config PHY_USING_DM9161CEP
- bool "DM9161CEP"
- config PHY_USING_LAN8742A
- bool "LAN8742A"
- endchoice
- endif
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_STM32_UART_V1_TX_TIMEOUT
- int "UART TX timeout"
- default 4000
- depends on RT_USING_SERIAL_V1
-
- menuconfig BSP_USING_UART3
- bool "Enable UART3"
- default n
- if BSP_USING_UART3
- config BSP_UART3_RX_USING_DMA
- bool "Enable UART3 RX DMA"
- depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
- default n
- config BSP_UART3_TX_USING_DMA
- bool "Enable UART3 TX DMA"
- depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
- default n
-
- config BSP_UART3_RX_BUFSIZE
- int "Set UART3 RX buffer size"
- range 64 65535
- depends on RT_USING_SERIAL_V2
- default 256
- config BSP_UART3_TX_BUFSIZE
- int "Set UART3 TX buffer size"
- range 0 65535
- depends on RT_USING_SERIAL_V2
- default 0
- config BSP_UART3_DMA_PING_BUFSIZE
- int "Set UART3 RX DMA ping-pong buffer size"
- range 32 65535
- depends on RT_USING_SERIAL_V2 && BSP_UART3_RX_USING_DMA
- default 64
- endif
- menuconfig BSP_USING_UART5
- bool "Enable UART5"
- default n
- if BSP_USING_UART5
- config BSP_UART5_RX_USING_DMA
- bool "Enable UART5 RX DMA"
- select RT_SERIAL_USING_DMA
- default n
- config BSP_UART5_TX_USING_DMA
- bool "Enable UART5 TX DMA"
- select RT_SERIAL_USING_DMA
- default n
- config BSP_UART5_RX_BUFSIZE
- int "Set UART5 RX buffer size"
- range 64 65535
- depends on BSP_USING_UART5
- default 256
- config BSP_UART5_TX_BUFSIZE
- int "Set UART5 TX buffer size"
- range 0 65535
- depends on BSP_USING_UART5
- default 0
- config BSP_UART5_DMA_PING_BUFSIZE
- int "Set UART5 RX DMA ping-pong buffer size"
- range 32 65535
- depends on RT_USING_SERIAL_V2 && BSP_UART5_RX_USING_DMA
- default 64
- endif
- endif
- menuconfig BSP_USING_SPI
- bool "Enable SPI BUS"
- default n
- select RT_USING_SPI
- if BSP_USING_SPI
- config BSP_USING_SPI1
- bool "Enable SPI1 BUS"
- default n
- config BSP_SPI1_TX_USING_DMA
- bool "Enable SPI1 TX DMA"
- depends on BSP_USING_SPI1
- default n
- config BSP_SPI1_RX_USING_DMA
- bool "Enable SPI1 RX DMA"
- depends on BSP_USING_SPI1
- select BSP_SPI1_TX_USING_DMA
- default n
- config BSP_USING_SPI2
- bool "Enable SPI2 BUS"
- default n
- config BSP_SPI2_TX_USING_DMA
- bool "Enable SPI2 TX DMA"
- depends on BSP_USING_SPI2
- default n
- config BSP_SPI2_RX_USING_DMA
- bool "Enable SPI2 RX DMA"
- depends on BSP_USING_SPI2
- select BSP_SPI2_TX_USING_DMA
- default n
- config BSP_USING_SPI3
- bool "Enable SPI3 BUS"
- default n
- config BSP_SPI3_TX_USING_DMA
- bool "Enable SPI3 TX DMA"
- depends on BSP_USING_SPI3
- default n
- config BSP_SPI3_RX_USING_DMA
- bool "Enable SPI3 RX DMA"
- depends on BSP_USING_SPI3
- select BSP_SPI3_TX_USING_DMA
- default n
- endif
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 0 175
- default 22
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 0 175
- default 23
- endif
- menuconfig BSP_USING_TIM
- bool "Enable timer"
- default n
- select RT_USING_HWTIMER
- if BSP_USING_TIM
- config BSP_USING_TIM2
- bool "Enable TIM2"
- default n
- config BSP_USING_TIM3
- bool "Enable TIM3"
- default n
- config BSP_USING_TIM4
- bool "Enable TIM4"
- default n
- config BSP_USING_TIM5
- bool "Enable TIM5"
- default n
- endif
- menuconfig BSP_USING_PWM
- bool "Enable PWM"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM3
- bool "Enable timer3 output PWM"
- default n
- if BSP_USING_PWM3
- config BSP_USING_PWM3_CH2
- bool "Enable PWM3 channel2"
- default n
- config BSP_USING_PWM3_CH3
- bool "Enable PWM3 channel3"
- default n
- config BSP_USING_PWM3_CH4
- bool "Enable PWM3 channel4"
- default n
- endif
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- menuconfig BSP_USING_ONCHIP_RTC
- bool "Enable RTC"
- select RT_USING_RTC
- default n
- if BSP_USING_ONCHIP_RTC
- choice
- prompt "Select clock source"
- default BSP_RTC_USING_LSE
- config BSP_RTC_USING_LSE
- bool "RTC USING LSE"
- config BSP_RTC_USING_LSI
- bool "RTC USING LSI"
- endchoice
- endif
- config BSP_USING_WDT
- bool "Enable Watchdog Timer"
- select RT_USING_WDT
- default n
- config BSP_USING_SDIO
- bool "Enable SDIO"
- select RT_USING_SDIO
- select RT_USING_DFS
- default n
- menuconfig BSP_USING_CAN
- bool "Enable CAN"
- default n
- select RT_USING_CAN
- if BSP_USING_CAN
- config BSP_USING_CAN1
- bool "using CAN1"
- default n
- endif
- config BSP_USING_USBD
- bool "Enable USB device"
- select RT_USING_USB_DEVICE
- default n
- if BSP_USING_USBD
- config BSP_USB_CONNECT_PIN
- int "USB connect pin"
- default 67
- config BSP_USB_PULL_UP_STATUS
- int "USB PULL UP STATUS"
- default 0
- endif
- source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
