| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128 |
- menu "Hardware Drivers Config"
- menu "Onboard Peripheral Drivers"
- config BSP_USING_STLINK_TO_USART
- bool "Enable STLINK TO USART (uart3)"
- select BSP_USING_UART
- select BSP_USING_UART3
- default y
- config BSP_USING_DSI
- bool "Enable LCD"
- select BSP_USING_SRAM
- select BSP_USING_GFXMMU
- default n
- menu "Enable Touch"
- config BSP_USING_TOUCH
- bool "Enable Touch drivers"
- select BSP_USING_I2C1
- default n
- if BSP_USING_TOUCH
- config BSP_TOUCH_INT_PIN
- int "Touch interrupt pin"
- default 34
- config BSP_I2C1_NAME
- string "I2C1 Name for Touch"
- default i2c1
- endif
- config TOUCH_IC_FT3X67
- bool "FT3X67"
- depends on BSP_USING_TOUCH
- default n
- endmenu
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_STM32_UART_V1_TX_TIMEOUT
- int "UART TX timeout"
- default 2000
- depends on RT_USING_SERIAL_V1
-
- menuconfig BSP_USING_UART3
- bool "Enable UART3"
- default y
- if BSP_USING_UART3
- config BSP_UART3_RX_USING_DMA
- bool "Enable UART3 RX DMA"
- depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
- default n
- config BSP_UART3_TX_USING_DMA
- bool "Enable UART3 TX DMA"
- depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
- default n
-
- config BSP_UART3_RX_BUFSIZE
- int "Set UART3 RX buffer size"
- range 64 65535
- depends on RT_USING_SERIAL_V2
- default 256
- config BSP_UART3_TX_BUFSIZE
- int "Set UART3 TX buffer size"
- range 0 65535
- depends on RT_USING_SERIAL_V2
- default 0
- config BSP_UART3_DMA_PING_BUFSIZE
- int "Set UART3 RX DMA ping-pong buffer size"
- range 32 65535
- depends on RT_USING_SERIAL_V2 && BSP_UART3_RX_USING_DMA
- default 64
- endif
- endif
- config BSP_USING_SRAM
- bool "Enable SRAM"
- select BSP_USING_FMC
- default n
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 1 216
- default 116
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 1 216
- default 117
- endif
- config BSP_USING_GFXMMU
- bool
- default n
- config BSP_USING_FMC
- bool
- default n
- source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
