| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125 |
- menu "Hardware Drivers Config"
- config SOC_STM32F410RB
- bool
- select SOC_SERIES_STM32F4
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_STLINK_TO_USART
- bool "Enable STLINK TO USART (uart2)"
- select BSP_USING_UART
- select BSP_USING_UART2
- default y
- config BSP_USING_ARDUINO
- bool "Compatible with Arduino Ecosystem (RTduino)"
- select PKG_USING_RTDUINO
- select BSP_USING_STLINK_TO_USART
- select BSP_USING_GPIO
- select BSP_USING_ADC
- select BSP_USING_ADC1
- select BSP_USING_PWM
- select BSP_USING_PWM1
- select BSP_USING_PWM1_CH3
- select BSP_USING_PWM1_CH2
- select BSP_USING_PWM1_CH1
- select BSP_USING_I2C
- select BSP_USING_I2C1
- imply RTDUINO_USING_SERVO
- imply RTDUINO_USING_WIRE
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default n
- config BSP_UART1_RX_USING_DMA
- bool "Enable UART1 RX DMA"
- depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
- default n
- config BSP_USING_UART2
- bool "Enable UART2"
- default y
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
- endif
- menuconfig BSP_USING_ADC
- bool "Enable ADC"
- default n
- select RT_USING_ADC
- if BSP_USING_ADC
- config BSP_USING_ADC1
- bool "Enable ADC1"
- default n
- endif
- menuconfig BSP_USING_PWM
- bool "Enable PWM"
- default n
- select RT_USING_PWM
- if BSP_USING_PWM
- menuconfig BSP_USING_PWM1
- bool "Enable timer1 output PWM"
- default n
- if BSP_USING_PWM1
- config BSP_USING_PWM1_CH1
- bool "Enable PWM1 channel1"
- default n
- config BSP_USING_PWM1_CH2
- bool "Enable PWM1 channel2"
- default n
- config BSP_USING_PWM1_CH3
- bool "Enable PWM1 channel3"
- default n
- endif
- endif
- menuconfig BSP_USING_I2C1
- bool "Enable I2C1 BUS (software simulation)"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C1
- comment "Notice: PB8 --> 24; PB9 --> 25"
- config BSP_I2C1_SCL_PIN
- int "i2c1 scl pin number"
- range 0 80
- default 24
- config BSP_I2C1_SDA_PIN
- int "I2C1 sda pin number"
- range 0 80
- default 25
- endif
- source "../libraries/HAL_Drivers/Kconfig"
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
