| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188 |
- menu "Hardware Drivers Config"
- config BSP_USING_HYPERFLASH
- bool
- default n
- config SOC_MIMXRT1052DVL6B
- bool
- select SOC_IMXRT1050_SERIES
- select BSP_USING_HYPERFLASH
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "On-chip Peripheral Drivers"
- config BSP_USING_DMA
- bool "Enable DMA"
- default n
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_LPUART
- bool "Enable UART"
- select RT_USING_SERIAL
- default y
- if BSP_USING_LPUART
- config BSP_USING_LPUART1
- bool "Enable LPUART1"
- default y
- config BSP_LPUART1_RX_USING_DMA
- bool "Enable LPUART1 RX DMA"
- depends on BSP_USING_LPUART1
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART1_RX_DMA_CHANNEL
- depends on BSP_LPUART1_RX_USING_DMA
- int "Set LPUART1 RX DMA channel (0-32)"
- default 0
- config BSP_LPUART1_TX_USING_DMA
- bool "Enable LPUART1 TX DMA"
- depends on BSP_USING_LPUART1
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART1_TX_DMA_CHANNEL
- depends on BSP_LPUART1_TX_USING_DMA
- int "Set LPUART1 TX DMA channel (0-32)"
- default 1
- config BSP_USING_LPUART3
- bool "Enable LPUART3"
- default n
- config BSP_LPUART3_RX_USING_DMA
- bool "Enable LPUART3 RX DMA"
- depends on BSP_USING_LPUART3
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART3_RX_DMA_CHANNEL
- depends on BSP_LPUART3_RX_USING_DMA
- int "Set LPUART3 RX DMA channel (0-32)"
- default 0
- config BSP_LPUART3_TX_USING_DMA
- bool "Enable LPUART3 TX DMA"
- depends on BSP_USING_LPUART3
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART3_TX_DMA_CHANNEL
- depends on BSP_LPUART3_TX_USING_DMA
- int "Set LPUART3 TX DMA channel (0-32)"
- default 1
- endif
- menuconfig BSP_USING_I2C
- bool "Enable I2C"
- select RT_USING_I2C
- default n
- if BSP_USING_I2C
- config BSP_USING_I2C1
- bool "Enable I2C1"
- default n
- choice
- prompt "Select I2C1 badurate"
- default HW_I2C1_BADURATE_100kHZ
- config HW_I2C1_BADURATE_100kHZ
- bool "Badurate 100kHZ"
- config HW_I2C1_BADURATE_400kHZ
- bool "Badurate 400kHZ"
- endchoice
- endif
- endmenu
- menu "Onboard Peripheral Drivers"
- config BSP_USING_SDRAM
- bool "Enable SDRAM"
- default n
- menuconfig BSP_USING_ETH
- bool "Enable Ethernet"
- select RT_USING_NETDEV
- select RT_USING_LWIP
- default n
- if BSP_USING_ETH
- config BSP_USING_PHY
- select RT_USING_PHY
- bool "Enable ethernet phy"
- default y
- if BSP_USING_PHY
- config PHY_DEVICE_ADDRESS
- int "Specify address of phy device"
- default 2
- config PHY_USING_KSZ8081
- bool "i.MX RT1052EVK uses ksz8081 phy"
- default y
- if PHY_USING_KSZ8081
- config PHY_RESET_PORT
- int "indicate port of reset"
- default 1
- config PHY_RESET_PIN
- int "indicate pin of reset"
- default 9
- config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
- bool "Enable the PHY ksz8081 RMII50M mode"
- depends on PHY_USING_KSZ8081
- default y
- endif
- endif
- endif
- menuconfig BSP_USING_AUDIO
- bool "Enable AUDIO (WM8960)"
- select BSP_USING_I2C1
- select RT_USING_AUDIO
- default n
- if BSP_USING_AUDIO
- config BSP_USING_AUDIO_PLAY
- bool "Enable Audio Play"
- default y
- if BSP_USING_AUDIO_PLAY
- config BSP_AUDIO_USING_DMA
- bool "Enable AUDIO DMA"
- default y
- endif
- config BSP_USING_AUDIO_RECORD
- bool "Enable Audio Record"
- select BSP_USING_AUDIO_PLAY
- default n
- if BSP_USING_AUDIO_RECORD
- config BSP_AUDIO_USING_DMA
- bool "Enable AUDIO DMA"
- default n
- endif
- endif
- endmenu
- menu "Board extended module Drivers"
- endmenu
- endmenu
|
