| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122 |
- menu "Hardware Drivers Config"
- config SOC_IMXRT1052CVL5B
- bool
- select SOC_IMXRT1050_SERIES
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_SDRAM
- bool "Enable SDRAM"
- default n
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_DMA
- bool "Enable DMA"
- default n
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_LPUART
- bool "Enable UART"
- select RT_USING_SERIAL
- default y
- if BSP_USING_LPUART
- config BSP_USING_LPUART1
- bool "Enable LPUART1"
- default y
- config BSP_LPUART1_RX_USING_DMA
- bool "Enable LPUART1 RX DMA"
- depends on BSP_USING_LPUART1
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART1_RX_DMA_CHANNEL
- depends on BSP_LPUART1_RX_USING_DMA
- int "Set LPUART1 RX DMA channel (0-32)"
- default 0
- config BSP_LPUART1_TX_USING_DMA
- bool "Enable LPUART1 TX DMA"
- depends on BSP_USING_LPUART1
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART1_TX_DMA_CHANNEL
- depends on BSP_LPUART1_TX_USING_DMA
- int "Set LPUART1 TX DMA channel (0-32)"
- default 1
- config BSP_USING_LPUART4
- bool "Enable LPUART4"
- default n
- config BSP_LPUART4_RX_USING_DMA
- bool "Enable LPUART4 RX DMA"
- depends on BSP_USING_LPUART4
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART4_RX_DMA_CHANNEL
- depends on BSP_LPUART4_RX_USING_DMA
- int "Set LPUART4 RX DMA channel (0-32)"
- default 2
- config BSP_LPUART4_TX_USING_DMA
- bool "Enable LPUART4 TX DMA"
- depends on BSP_USING_LPUART4
- select BSP_USING_DMA
- select RT_SERIAL_USING_DMA
- default n
- config BSP_LPUART4_TX_DMA_CHANNEL
- depends on BSP_LPUART4_TX_USING_DMA
- int "Set LPUART4 TX DMA channel (0-32)"
- default 3
- endif
- menuconfig BSP_USING_SPI
- bool "Enable SPI"
- select RT_USING_SPI
- select RT_USING_PIN
- default n
- if BSP_USING_SPI
- config BSP_USING_SPI3
- bool "Enable SPI3"
- default n
- config BSP_SPI3_USING_DMA
- bool "Enable SPI3 DMA xfer"
- depends on BSP_USING_SPI3
- select BSP_USING_DMA
- default n
- config BSP_SPI3_RX_DMA_CHANNEL
- depends on BSP_SPI3_USING_DMA
- int "Set SPI3 RX DMA channel (0-32)"
- default 4
- config BSP_SPI3_TX_DMA_CHANNEL
- depends on BSP_SPI3_USING_DMA
- int "Set SPI3 TX DMA channel (0-32)"
- default 5
- endif
- endmenu
- endmenu
|
