Add STM32CubeMX initial configuration

bsp/stm32/stm32l476-st-nucleo/README.md

@@ -48,8 +48,6 @@
 | TIME              |     支持     | TIME15/16/17 |
 | **扩展模块**      | **支持情况** | **备注** |
 
-注意：部分片上外设默认没有使能，如需使用请在CubeMX中使能相应外设
-
 ## 使用说明
 
 使用说明分为如下两个章节：

bsp/stm32/stm32l476-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc

@@ -1,146 +1,196 @@
 #MicroXplorer Configuration settings - do not modify
-File.Version=6
-KeepUserPlacement=false
 Mcu.Family=STM32L4
+PC3.Mode=Full_Duplex_Master
+ProjectManager.MainLocation=Src
+PA6.Mode=Full_Duplex_Master
+RCC.USART1Freq_Value=80000000
+RCC.SAI1Freq_Value=18285714.285714287
+USART2.IPParameters=VirtualMode-Asynchronous
+RCC.CortexFreq_Value=80000000
+SPI3.Direction=SPI_DIRECTION_2LINES
+VP_TIM17_VS_ClockSourceINT.Mode=Enable_Timer
+SPI3.VirtualType=VM_MASTER
+ProjectManager.KeepUserCode=true
+Mcu.UserName=STM32L476RGTx
+SPI1.VirtualType=VM_MASTER
+SPI2.VirtualType=VM_MASTER
+PB10.Mode=Full_Duplex_Master
+PC10.Signal=SPI3_SCK
+PC12.Signal=SPI3_MOSI
+RCC.PLLSAI1RoutputFreq_Value=64000000
+ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-SystemClock_Config-RCC-false-HAL-false,3-MX_USART2_UART_Init-USART2-false-HAL-true,4-MX_RTC_Init-RTC-false-HAL-true,5-MX_SPI1_Init-SPI1-false-HAL-true,6-MX_SPI2_Init-SPI2-false-HAL-true,7-MX_SPI3_Init-SPI3-false-HAL-true,8-MX_TIM15_Init-TIM15-false-HAL-true,9-MX_TIM16_Init-TIM16-false-HAL-true,10-MX_TIM17_Init-TIM17-false-HAL-true
+VP_RTC_VS_RTC_Activate.Mode=RTC_Enabled
+RCC.RTCFreq_Value=32768
+RCC.USART2Freq_Value=80000000
+PC15-OSC32_OUT\ (PC15).Mode=LSE-External-Oscillator
+PinOutPanel.RotationAngle=0
+RCC.MCO1PinFreq_Value=80000000
+RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK
+ProjectManager.StackSize=0x400
+PC14-OSC32_IN\ (PC14).Mode=LSE-External-Oscillator
+PA14\ (JTCK-SWCLK).Signal=SYS_JTCK-SWCLK
+RCC.I2C3Freq_Value=80000000
+RCC.LPTIM1Freq_Value=80000000
+Mcu.IP4=SPI2
+RCC.FCLKCortexFreq_Value=80000000
+Mcu.IP5=SPI3
+NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+Mcu.IP2=RTC
+Mcu.IP3=SPI1
 Mcu.IP0=NVIC
 Mcu.IP1=RCC
-Mcu.IP2=RTC
-Mcu.IP3=SYS
-Mcu.IP4=USART2
-Mcu.IPNb=5
-Mcu.Name=STM32L476R(C-E-G)Tx
-Mcu.Package=LQFP64
+Mcu.UserConstants=
+RCC.VCOSAI1OutputFreq_Value=128000000
+RCC.SDMMCFreq_Value=64000000
+Mcu.ThirdPartyNb=0
+SPI1.Direction=SPI_DIRECTION_2LINES
+RCC.HCLKFreq_Value=80000000
+Mcu.IPNb=11
+ProjectManager.PreviousToolchain=
+RCC.APB2TimFreq_Value=80000000
+SPI1.CalculateBaudRate=40.0 MBits/s
+PC3.Signal=SPI2_MOSI
+Mcu.Pin6=PA5
+RCC.SAI2Freq_Value=18285714.285714287
+Mcu.Pin7=PA6
+Mcu.Pin8=PA7
+Mcu.Pin9=PB10
+RCC.AHBFreq_Value=80000000
 Mcu.Pin0=PC14-OSC32_IN (PC14)
 Mcu.Pin1=PC15-OSC32_OUT (PC15)
-Mcu.Pin2=PA2
-Mcu.Pin3=PA3
-Mcu.Pin4=PA13 (JTMS-SWDIO)
-Mcu.Pin5=PA14 (JTCK-SWCLK)
-Mcu.Pin6=VP_RTC_VS_RTC_Activate
-Mcu.Pin7=VP_SYS_VS_Systick
-Mcu.PinsNb=8
-Mcu.ThirdPartyNb=0
-Mcu.UserConstants=
-Mcu.UserName=STM32L476RGTx
-MxCube.Version=5.0.1
-MxDb.Version=DB.5.0.1
-NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
-NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
-NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
-PA13\ (JTMS-SWDIO).Mode=Serial_Wire
-PA13\ (JTMS-SWDIO).Signal=SYS_JTMS-SWDIO
-PA14\ (JTCK-SWCLK).Mode=Serial_Wire
-PA14\ (JTCK-SWCLK).Signal=SYS_JTCK-SWCLK
-PA2.Mode=Asynchronous
-PA2.Signal=USART2_TX
-PA3.Mode=Asynchronous
-PA3.Signal=USART2_RX
-PC14-OSC32_IN\ (PC14).Mode=LSE-External-Oscillator
-PC14-OSC32_IN\ (PC14).Signal=RCC_OSC32_IN
-PC15-OSC32_OUT\ (PC15).Mode=LSE-External-Oscillator
-PC15-OSC32_OUT\ (PC15).Signal=RCC_OSC32_OUT
-PCC.Checker=true
-PCC.Line=STM32L4x6
-PCC.MCU=STM32L476R(C-E-G)Tx
-PCC.PartNumber=STM32L476RGTx
-PCC.Seq0=0
-PCC.Series=STM32L4
-PCC.Temperature=25
-PCC.Vdd=null
-PinOutPanel.RotationAngle=0
-ProjectManager.AskForMigrate=true
+Mcu.Pin2=PC2
+Mcu.Pin3=PC3
+RCC.USART3Freq_Value=80000000
+Mcu.Pin4=PA2
+Mcu.Pin5=PA3
+ProjectManager.ProjectBuild=false
+RCC.HSE_VALUE=8000000
+NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+Mcu.IP10=USART2
+USART2.VirtualMode-Asynchronous=VM_ASYNC
+RCC.RTCClockSelection=RCC_RTCCLKSOURCE_LSE
+NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
+ProjectManager.FirmwarePackage=STM32Cube FW_L4 V1.15.1
+MxDb.Version=DB.5.0.60
 ProjectManager.BackupPrevious=false
-ProjectManager.CompilerOptimize=6
-ProjectManager.ComputerToolchain=false
-ProjectManager.CoupleFile=false
-ProjectManager.CustomerFirmwarePackage=
-ProjectManager.DefaultFWLocation=true
-ProjectManager.DeletePrevious=true
-ProjectManager.DeviceId=STM32L476RGTx
-ProjectManager.FirmwarePackage=STM32Cube FW_L4 V1.13.0
-ProjectManager.FreePins=false
+RCC.VCOInputFreq_Value=16000000
+File.Version=6
+SPI2.CalculateBaudRate=40.0 MBits/s
+RCC.PLLRCLKFreq_Value=80000000
+NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+VP_TIM15_VS_ClockSourceINT.Signal=TIM15_VS_ClockSourceINT
 ProjectManager.HalAssertFull=false
-ProjectManager.HeapSize=0x200
-ProjectManager.KeepUserCode=true
-ProjectManager.LastFirmware=true
-ProjectManager.LibraryCopy=0
-ProjectManager.MainLocation=Src
-ProjectManager.NoMain=false
-ProjectManager.PreviousToolchain=
-ProjectManager.ProjectBuild=false
-ProjectManager.ProjectFileName=CubeMX_Config.ioc
 ProjectManager.ProjectName=CubeMX_Config
-ProjectManager.StackSize=0x400
-ProjectManager.TargetToolchain=MDK-ARM V5
+Mcu.Package=LQFP64
+PA6.Signal=SPI1_MISO
+SPI2.Mode=SPI_MODE_MASTER
+SPI3.Mode=SPI_MODE_MASTER
 ProjectManager.ToolChainLocation=
-ProjectManager.UnderRoot=false
-ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-SystemClock_Config-RCC-false-HAL-false,3-MX_USART2_UART_Init-USART2-false-HAL-true,4-MX_RTC_Init-RTC-false-HAL-true
-RCC.ADCFreq_Value=64000000
-RCC.AHBFreq_Value=80000000
-RCC.APB1Freq_Value=80000000
-RCC.APB1TimFreq_Value=80000000
-RCC.APB2Freq_Value=80000000
-RCC.APB2TimFreq_Value=80000000
-RCC.CortexFreq_Value=80000000
+RCC.LSI_VALUE=32000
+VP_SYS_VS_Systick.Signal=SYS_VS_Systick
+RCC.LSCOPinFreq_Value=32000
 RCC.DFSDMFreq_Value=80000000
-RCC.FCLKCortexFreq_Value=80000000
-RCC.FamilyName=M
-RCC.HCLKFreq_Value=80000000
-RCC.HSE_VALUE=8000000
-RCC.HSI_VALUE=16000000
-RCC.I2C1Freq_Value=80000000
-RCC.I2C2Freq_Value=80000000
-RCC.I2C3Freq_Value=80000000
-RCC.IPParameters=ADCFreq_Value,AHBFreq_Value,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,CortexFreq_Value,DFSDMFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,LCDFreq_Value,LPTIM1Freq_Value,LPTIM2Freq_Value,LPUART1Freq_Value,LSCOPinFreq_Value,LSI_VALUE,MCO1PinFreq_Value,MSI_VALUE,PLLN,PLLPoutputFreq_Value,PLLQoutputFreq_Value,PLLRCLKFreq_Value,PLLSAI1PoutputFreq_Value,PLLSAI1QoutputFreq_Value,PLLSAI1RoutputFreq_Value,PLLSAI2PoutputFreq_Value,PLLSAI2RoutputFreq_Value,PLLSourceVirtual,PWRFreq_Value,RNGFreq_Value,RTCClockSelection,RTCFreq_Value,SAI1Freq_Value,SAI2Freq_Value,SDMMCFreq_Value,SWPMI1Freq_Value,SYSCLKFreq_VALUE,SYSCLKSource,UART4Freq_Value,UART5Freq_Value,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,USBFreq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VCOSAI1OutputFreq_Value,VCOSAI2OutputFreq_Value
-RCC.LCDFreq_Value=32768
-RCC.LPTIM1Freq_Value=80000000
-RCC.LPTIM2Freq_Value=80000000
+PC11.Mode=Full_Duplex_Master
+RCC.PLLPoutputFreq_Value=22857142.85714286
+RCC.APB1TimFreq_Value=80000000
+NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
 RCC.LPUART1Freq_Value=80000000
-RCC.LSCOPinFreq_Value=32000
-RCC.LSI_VALUE=32000
-RCC.MCO1PinFreq_Value=80000000
+SPI3.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate
+SPI2.Direction=SPI_DIRECTION_2LINES
+PA13\ (JTMS-SWDIO).Signal=SYS_JTMS-SWDIO
+ProjectManager.CustomerFirmwarePackage=
+PA3.Signal=USART2_RX
+PA5.Mode=Full_Duplex_Master
+VP_RTC_VS_RTC_Activate.Signal=RTC_VS_RTC_Activate
 RCC.MSI_VALUE=4000000
-RCC.PLLN=10
-RCC.PLLPoutputFreq_Value=22857142.85714286
-RCC.PLLQoutputFreq_Value=80000000
-RCC.PLLRCLKFreq_Value=80000000
-RCC.PLLSAI1PoutputFreq_Value=18285714.285714287
-RCC.PLLSAI1QoutputFreq_Value=64000000
-RCC.PLLSAI1RoutputFreq_Value=64000000
-RCC.PLLSAI2PoutputFreq_Value=18285714.285714287
-RCC.PLLSAI2RoutputFreq_Value=64000000
 RCC.PLLSourceVirtual=RCC_PLLSOURCE_HSI
-RCC.PWRFreq_Value=80000000
-RCC.RNGFreq_Value=64000000
-RCC.RTCClockSelection=RCC_RTCCLKSOURCE_LSE
-RCC.RTCFreq_Value=32768
-RCC.SAI1Freq_Value=18285714.285714287
-RCC.SAI2Freq_Value=18285714.285714287
-RCC.SDMMCFreq_Value=64000000
+PA14\ (JTCK-SWCLK).Mode=Serial_Wire
+RCC.PLLQoutputFreq_Value=80000000
+ProjectManager.ProjectFileName=CubeMX_Config.ioc
+PA7.Mode=Full_Duplex_Master
+Mcu.PinsNb=20
+ProjectManager.NoMain=false
+SPI1.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate
+PC11.Signal=SPI3_MISO
 RCC.SWPMI1Freq_Value=80000000
-RCC.SYSCLKFreq_VALUE=80000000
-RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK
-RCC.UART4Freq_Value=80000000
-RCC.UART5Freq_Value=80000000
-RCC.USART1Freq_Value=80000000
-RCC.USART2Freq_Value=80000000
-RCC.USART3Freq_Value=80000000
+PC2.Signal=SPI2_MISO
+PC10.Mode=Full_Duplex_Master
+ProjectManager.DefaultFWLocation=true
+PC2.Mode=Full_Duplex_Master
+PC15-OSC32_OUT\ (PC15).Signal=RCC_OSC32_OUT
+VP_TIM16_VS_ClockSourceINT.Mode=Enable_Timer
+ProjectManager.DeletePrevious=true
+RCC.VCOSAI2OutputFreq_Value=128000000
+VP_TIM17_VS_ClockSourceINT.Signal=TIM17_VS_ClockSourceINT
+RCC.FamilyName=M
+PA3.Mode=Asynchronous
+ProjectManager.TargetToolchain=MDK-ARM V5
+SPI2.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate
 RCC.USBFreq_Value=64000000
-RCC.VCOInputFreq_Value=16000000
+RCC.PLLSAI1PoutputFreq_Value=18285714.285714287
+PB10.Signal=SPI2_SCK
+RCC.PLLSAI2RoutputFreq_Value=64000000
+PA5.Signal=SPI1_SCK
+PC12.Mode=Full_Duplex_Master
+board=custom
 RCC.VCOOutputFreq_Value=160000000
-RCC.VCOSAI1OutputFreq_Value=128000000
-RCC.VCOSAI2OutputFreq_Value=128000000
-USART2.IPParameters=VirtualMode-Asynchronous
-USART2.VirtualMode-Asynchronous=VM_ASYNC
-VP_RTC_VS_RTC_Activate.Mode=RTC_Enabled
-VP_RTC_VS_RTC_Activate.Signal=RTC_VS_RTC_Activate
+ProjectManager.LastFirmware=true
+RCC.APB2Freq_Value=80000000
+RCC.UART4Freq_Value=80000000
+SPI3.CalculateBaudRate=40.0 MBits/s
+MxCube.Version=5.6.1
+RCC.I2C1Freq_Value=80000000
+SPI1.Mode=SPI_MODE_MASTER
+RCC.LCDFreq_Value=32768
+RCC.RNGFreq_Value=64000000
+RCC.PLLSAI1QoutputFreq_Value=64000000
+RCC.ADCFreq_Value=64000000
 VP_SYS_VS_Systick.Mode=SysTick
-VP_SYS_VS_Systick.Signal=SYS_VS_Systick
-board=custom
+VP_TIM16_VS_ClockSourceINT.Signal=TIM16_VS_ClockSourceINT
+NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+RCC.UART5Freq_Value=80000000
+ProjectManager.FreePins=false
+RCC.IPParameters=ADCFreq_Value,AHBFreq_Value,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,CortexFreq_Value,DFSDMFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,LCDFreq_Value,LPTIM1Freq_Value,LPTIM2Freq_Value,LPUART1Freq_Value,LSCOPinFreq_Value,LSI_VALUE,MCO1PinFreq_Value,MSI_VALUE,PLLN,PLLPoutputFreq_Value,PLLQoutputFreq_Value,PLLRCLKFreq_Value,PLLSAI1PoutputFreq_Value,PLLSAI1QoutputFreq_Value,PLLSAI1RoutputFreq_Value,PLLSAI2PoutputFreq_Value,PLLSAI2RoutputFreq_Value,PLLSourceVirtual,PWRFreq_Value,RNGFreq_Value,RTCClockSelection,RTCFreq_Value,SAI1Freq_Value,SAI2Freq_Value,SDMMCFreq_Value,SWPMI1Freq_Value,SYSCLKFreq_VALUE,SYSCLKSource,UART4Freq_Value,UART5Freq_Value,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,USBFreq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VCOSAI1OutputFreq_Value,VCOSAI2OutputFreq_Value
+ProjectManager.AskForMigrate=true
+Mcu.Name=STM32L476R(C-E-G)Tx
+RCC.LPTIM2Freq_Value=80000000
+PA2.Signal=USART2_TX
+ProjectManager.UnderRoot=false
+Mcu.IP8=TIM16
+Mcu.IP9=TIM17
+Mcu.IP6=SYS
+Mcu.IP7=TIM15
+ProjectManager.CoupleFile=false
+PA13\ (JTMS-SWDIO).Mode=Serial_Wire
+RCC.SYSCLKFreq_VALUE=80000000
+RCC.PLLSAI2PoutputFreq_Value=18285714.285714287
+NVIC.ForceEnableDMAVector=true
+KeepUserPlacement=false
+PC14-OSC32_IN\ (PC14).Signal=RCC_OSC32_IN
+NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+ProjectManager.CompilerOptimize=6
+VP_TIM15_VS_ClockSourceINT.Mode=Internal
+ProjectManager.HeapSize=0x200
+Mcu.Pin15=VP_RTC_VS_RTC_Activate
+NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
+Mcu.Pin16=VP_SYS_VS_Systick
+Mcu.Pin13=PC11
+Mcu.Pin14=PC12
+Mcu.Pin19=VP_TIM17_VS_ClockSourceINT
+ProjectManager.ComputerToolchain=false
+Mcu.Pin17=VP_TIM15_VS_ClockSourceINT
+RCC.HSI_VALUE=16000000
+Mcu.Pin18=VP_TIM16_VS_ClockSourceINT
+NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
+Mcu.Pin11=PA14 (JTCK-SWCLK)
+Mcu.Pin12=PC10
+RCC.PLLN=10
+Mcu.Pin10=PA13 (JTMS-SWDIO)
+PA2.Mode=Asynchronous
+RCC.PWRFreq_Value=80000000
+RCC.I2C2Freq_Value=80000000
+RCC.APB1Freq_Value=80000000
+ProjectManager.DeviceId=STM32L476RGTx
+ProjectManager.LibraryCopy=2
+PA7.Signal=SPI1_MOSI

bsp/stm32/stm32l476-st-nucleo/board/CubeMX_Config/Inc/stm32l4xx_hal_conf.h

@@ -5,7 +5,7 @@
   ******************************************************************************
   * @attention
   *
-  * <h2><center>&copy; COPYRIGHT(c) 2019 STMicroelectronics</center></h2>
+  * <h2><center>&copy; COPYRIGHT(c) 2020 STMicroelectronics</center></h2>
   *
   * Redistribution and use in source and binary forms, with or without modification,
   * are permitted provided that the following conditions are met:
@@ -69,13 +69,15 @@
 /*#define HAL_IWDG_MODULE_ENABLED   */
 /*#define HAL_LTDC_MODULE_ENABLED   */
 /*#define HAL_LCD_MODULE_ENABLED   */
-#define HAL_LPTIM_MODULE_ENABLED
+/*#define HAL_LPTIM_MODULE_ENABLED   */
+/*#define HAL_MMC_MODULE_ENABLED   */
 /*#define HAL_NAND_MODULE_ENABLED   */
 /*#define HAL_NOR_MODULE_ENABLED   */
 /*#define HAL_OPAMP_MODULE_ENABLED   */
 /*#define HAL_OSPI_MODULE_ENABLED   */
 /*#define HAL_OSPI_MODULE_ENABLED   */
 /*#define HAL_PCD_MODULE_ENABLED   */
+/*#define HAL_PKA_MODULE_ENABLED   */
 /*#define HAL_QSPI_MODULE_ENABLED   */
 /*#define HAL_QSPI_MODULE_ENABLED   */
 /*#define HAL_RNG_MODULE_ENABLED   */
@@ -84,16 +86,18 @@
 /*#define HAL_SD_MODULE_ENABLED   */
 /*#define HAL_SMBUS_MODULE_ENABLED   */
 /*#define HAL_SMARTCARD_MODULE_ENABLED   */
-/*#define HAL_SPI_MODULE_ENABLED   */
+#define HAL_SPI_MODULE_ENABLED
 /*#define HAL_SRAM_MODULE_ENABLED   */
 /*#define HAL_SWPMI_MODULE_ENABLED   */
-/*#define HAL_TIM_MODULE_ENABLED   */
+#define HAL_TIM_MODULE_ENABLED
 /*#define HAL_TSC_MODULE_ENABLED   */
 #define HAL_UART_MODULE_ENABLED
 /*#define HAL_USART_MODULE_ENABLED   */
 /*#define HAL_WWDG_MODULE_ENABLED   */
 /*#define HAL_EXTI_MODULE_ENABLED   */
+/*#define HAL_PSSI_MODULE_ENABLED   */
 #define HAL_GPIO_MODULE_ENABLED
+#define HAL_EXTI_MODULE_ENABLED 
 #define HAL_I2C_MODULE_ENABLED
 #define HAL_DMA_MODULE_ENABLED
 #define HAL_RCC_MODULE_ENABLED
@@ -296,6 +300,10 @@
   #include "stm32l4xx_hal_sram.h"
 #endif /* HAL_SRAM_MODULE_ENABLED */
 
+#ifdef HAL_MMC_MODULE_ENABLED
+  #include "stm32l4xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
+
 #ifdef HAL_NOR_MODULE_ENABLED
   #include "stm32l4xx_hal_nor.h"
 #endif /* HAL_NOR_MODULE_ENABLED */
@@ -332,6 +340,10 @@
   #include "stm32l4xx_hal_ospi.h"
 #endif /* HAL_OSPI_MODULE_ENABLED */
 
+#ifdef HAL_PKA_MODULE_ENABLED
+  #include "stm32l4xx_hal_pka.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
 #ifdef HAL_PWR_MODULE_ENABLED
   #include "stm32l4xx_hal_pwr.h"
 #endif /* HAL_PWR_MODULE_ENABLED */
@@ -408,6 +420,10 @@
   #include "stm32l4xx_hal_gfxmmu.h"
 #endif /* HAL_GFXMMU_MODULE_ENABLED */
 
+#ifdef HAL_PSSI_MODULE_ENABLED
+  #include "stm32l4xx_hal_pssi.h"
+#endif /* HAL_PSSI_MODULE_ENABLED */
+
 /* Exported macro ------------------------------------------------------------*/
 #ifdef  USE_FULL_ASSERT
 /**
@@ -418,7 +434,7 @@
   *         If expr is true, it returns no value.
   * @retval None
   */
-  #define assert_param(expr) ((expr) ? (void)0U : assert_failed((char *)__FILE__, __LINE__))
+  #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
 /* Exported functions ------------------------------------------------------- */
   void assert_failed(char *file, uint32_t line);
 #else

bsp/stm32/stm32l476-st-nucleo/board/CubeMX_Config/Src/main.c

@@ -64,6 +64,14 @@
 /* Private variables ---------------------------------------------------------*/
 RTC_HandleTypeDef hrtc;
 
+SPI_HandleTypeDef hspi1;
+SPI_HandleTypeDef hspi2;
+SPI_HandleTypeDef hspi3;
+
+TIM_HandleTypeDef htim15;
+TIM_HandleTypeDef htim16;
+TIM_HandleTypeDef htim17;
+
 UART_HandleTypeDef huart2;
 
 /* USER CODE BEGIN PV */
@@ -76,6 +84,12 @@ void SystemClock_Config(void);
 static void MX_GPIO_Init(void);
 static void MX_USART2_UART_Init(void);
 static void MX_RTC_Init(void);
+static void MX_SPI1_Init(void);
+static void MX_SPI2_Init(void);
+static void MX_SPI3_Init(void);
+static void MX_TIM15_Init(void);
+static void MX_TIM16_Init(void);
+static void MX_TIM17_Init(void);
 /* USER CODE BEGIN PFP */
 /* Private function prototypes -----------------------------------------------*/
 
@@ -116,6 +130,12 @@ int main(void)
   MX_GPIO_Init();
   MX_USART2_UART_Init();
   MX_RTC_Init();
+  MX_SPI1_Init();
+  MX_SPI2_Init();
+  MX_SPI3_Init();
+  MX_TIM15_Init();
+  MX_TIM16_Init();
+  MX_TIM17_Init();
   /* USER CODE BEGIN 2 */
 
   /* USER CODE END 2 */
@@ -143,11 +163,11 @@ void SystemClock_Config(void)
   RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
   RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
 
-  /**Configure LSE Drive Capability 
+  /** Configure LSE Drive Capability 
   */
   HAL_PWR_EnableBkUpAccess();
   __HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_LOW);
-  /**Initializes the CPU, AHB and APB busses clocks 
+  /** Initializes the CPU, AHB and APB busses clocks 
   */
   RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_LSE;
   RCC_OscInitStruct.LSEState = RCC_LSE_ON;
@@ -164,7 +184,7 @@ void SystemClock_Config(void)
   {
     Error_Handler();
   }
-  /**Initializes the CPU, AHB and APB busses clocks 
+  /** Initializes the CPU, AHB and APB busses clocks 
   */
   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                               |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
@@ -184,7 +204,7 @@ void SystemClock_Config(void)
   {
     Error_Handler();
   }
-  /**Configure the main internal regulator output voltage 
+  /** Configure the main internal regulator output voltage 
   */
   if (HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1) != HAL_OK)
   {
@@ -207,7 +227,7 @@ static void MX_RTC_Init(void)
   /* USER CODE BEGIN RTC_Init 1 */
 
   /* USER CODE END RTC_Init 1 */
-  /**Initialize RTC Only 
+  /** Initialize RTC Only 
   */
   hrtc.Instance = RTC;
   hrtc.Init.HourFormat = RTC_HOURFORMAT_24;
@@ -227,6 +247,236 @@ static void MX_RTC_Init(void)
 
 }
 
+/**
+  * @brief SPI1 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_SPI1_Init(void)
+{
+
+  /* USER CODE BEGIN SPI1_Init 0 */
+
+  /* USER CODE END SPI1_Init 0 */
+
+  /* USER CODE BEGIN SPI1_Init 1 */
+
+  /* USER CODE END SPI1_Init 1 */
+  /* SPI1 parameter configuration*/
+  hspi1.Instance = SPI1;
+  hspi1.Init.Mode = SPI_MODE_MASTER;
+  hspi1.Init.Direction = SPI_DIRECTION_2LINES;
+  hspi1.Init.DataSize = SPI_DATASIZE_4BIT;
+  hspi1.Init.CLKPolarity = SPI_POLARITY_LOW;
+  hspi1.Init.CLKPhase = SPI_PHASE_1EDGE;
+  hspi1.Init.NSS = SPI_NSS_SOFT;
+  hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;
+  hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB;
+  hspi1.Init.TIMode = SPI_TIMODE_DISABLE;
+  hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
+  hspi1.Init.CRCPolynomial = 7;
+  hspi1.Init.CRCLength = SPI_CRC_LENGTH_DATASIZE;
+  hspi1.Init.NSSPMode = SPI_NSS_PULSE_ENABLE;
+  if (HAL_SPI_Init(&hspi1) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN SPI1_Init 2 */
+
+  /* USER CODE END SPI1_Init 2 */
+
+}
+
+/**
+  * @brief SPI2 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_SPI2_Init(void)
+{
+
+  /* USER CODE BEGIN SPI2_Init 0 */
+
+  /* USER CODE END SPI2_Init 0 */
+
+  /* USER CODE BEGIN SPI2_Init 1 */
+
+  /* USER CODE END SPI2_Init 1 */
+  /* SPI2 parameter configuration*/
+  hspi2.Instance = SPI2;
+  hspi2.Init.Mode = SPI_MODE_MASTER;
+  hspi2.Init.Direction = SPI_DIRECTION_2LINES;
+  hspi2.Init.DataSize = SPI_DATASIZE_4BIT;
+  hspi2.Init.CLKPolarity = SPI_POLARITY_LOW;
+  hspi2.Init.CLKPhase = SPI_PHASE_1EDGE;
+  hspi2.Init.NSS = SPI_NSS_SOFT;
+  hspi2.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;
+  hspi2.Init.FirstBit = SPI_FIRSTBIT_MSB;
+  hspi2.Init.TIMode = SPI_TIMODE_DISABLE;
+  hspi2.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
+  hspi2.Init.CRCPolynomial = 7;
+  hspi2.Init.CRCLength = SPI_CRC_LENGTH_DATASIZE;
+  hspi2.Init.NSSPMode = SPI_NSS_PULSE_ENABLE;
+  if (HAL_SPI_Init(&hspi2) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN SPI2_Init 2 */
+
+  /* USER CODE END SPI2_Init 2 */
+
+}
+
+/**
+  * @brief SPI3 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_SPI3_Init(void)
+{
+
+  /* USER CODE BEGIN SPI3_Init 0 */
+
+  /* USER CODE END SPI3_Init 0 */
+
+  /* USER CODE BEGIN SPI3_Init 1 */
+
+  /* USER CODE END SPI3_Init 1 */
+  /* SPI3 parameter configuration*/
+  hspi3.Instance = SPI3;
+  hspi3.Init.Mode = SPI_MODE_MASTER;
+  hspi3.Init.Direction = SPI_DIRECTION_2LINES;
+  hspi3.Init.DataSize = SPI_DATASIZE_4BIT;
+  hspi3.Init.CLKPolarity = SPI_POLARITY_LOW;
+  hspi3.Init.CLKPhase = SPI_PHASE_1EDGE;
+  hspi3.Init.NSS = SPI_NSS_SOFT;
+  hspi3.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;
+  hspi3.Init.FirstBit = SPI_FIRSTBIT_MSB;
+  hspi3.Init.TIMode = SPI_TIMODE_DISABLE;
+  hspi3.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
+  hspi3.Init.CRCPolynomial = 7;
+  hspi3.Init.CRCLength = SPI_CRC_LENGTH_DATASIZE;
+  hspi3.Init.NSSPMode = SPI_NSS_PULSE_ENABLE;
+  if (HAL_SPI_Init(&hspi3) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN SPI3_Init 2 */
+
+  /* USER CODE END SPI3_Init 2 */
+
+}
+
+/**
+  * @brief TIM15 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_TIM15_Init(void)
+{
+
+  /* USER CODE BEGIN TIM15_Init 0 */
+
+  /* USER CODE END TIM15_Init 0 */
+
+  TIM_ClockConfigTypeDef sClockSourceConfig = {0};
+  TIM_MasterConfigTypeDef sMasterConfig = {0};
+
+  /* USER CODE BEGIN TIM15_Init 1 */
+
+  /* USER CODE END TIM15_Init 1 */
+  htim15.Instance = TIM15;
+  htim15.Init.Prescaler = 0;
+  htim15.Init.CounterMode = TIM_COUNTERMODE_UP;
+  htim15.Init.Period = 0;
+  htim15.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
+  htim15.Init.RepetitionCounter = 0;
+  htim15.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
+  if (HAL_TIM_Base_Init(&htim15) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_INTERNAL;
+  if (HAL_TIM_ConfigClockSource(&htim15, &sClockSourceConfig) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;
+  sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
+  if (HAL_TIMEx_MasterConfigSynchronization(&htim15, &sMasterConfig) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN TIM15_Init 2 */
+
+  /* USER CODE END TIM15_Init 2 */
+
+}
+
+/**
+  * @brief TIM16 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_TIM16_Init(void)
+{
+
+  /* USER CODE BEGIN TIM16_Init 0 */
+
+  /* USER CODE END TIM16_Init 0 */
+
+  /* USER CODE BEGIN TIM16_Init 1 */
+
+  /* USER CODE END TIM16_Init 1 */
+  htim16.Instance = TIM16;
+  htim16.Init.Prescaler = 0;
+  htim16.Init.CounterMode = TIM_COUNTERMODE_UP;
+  htim16.Init.Period = 0;
+  htim16.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
+  htim16.Init.RepetitionCounter = 0;
+  htim16.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
+  if (HAL_TIM_Base_Init(&htim16) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN TIM16_Init 2 */
+
+  /* USER CODE END TIM16_Init 2 */
+
+}
+
+/**
+  * @brief TIM17 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_TIM17_Init(void)
+{
+
+  /* USER CODE BEGIN TIM17_Init 0 */
+
+  /* USER CODE END TIM17_Init 0 */
+
+  /* USER CODE BEGIN TIM17_Init 1 */
+
+  /* USER CODE END TIM17_Init 1 */
+  htim17.Instance = TIM17;
+  htim17.Init.Prescaler = 0;
+  htim17.Init.CounterMode = TIM_COUNTERMODE_UP;
+  htim17.Init.Period = 0;
+  htim17.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
+  htim17.Init.RepetitionCounter = 0;
+  htim17.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
+  if (HAL_TIM_Base_Init(&htim17) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN TIM17_Init 2 */
+
+  /* USER CODE END TIM17_Init 2 */
+
+}
+
 /**
   * @brief USART2 Initialization Function
   * @param None
@@ -273,6 +523,7 @@ static void MX_GPIO_Init(void)
   /* GPIO Ports Clock Enable */
   __HAL_RCC_GPIOC_CLK_ENABLE();
   __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOB_CLK_ENABLE();
 
 }
 
@@ -302,7 +553,7 @@ void Error_Handler(void)
   * @param  line: assert_param error line source number
   * @retval None
   */
-void assert_failed(char *file, uint32_t line)
+void assert_failed(uint8_t *file, uint32_t line)
 { 
   /* USER CODE BEGIN 6 */
   /* User can add his own implementation to report the file name and line number,

bsp/stm32/stm32l476-st-nucleo/board/CubeMX_Config/Src/stm32l4xx_hal_msp.c

@@ -105,7 +105,6 @@ void HAL_MspInit(void)
 */
 void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc)
 {
-
   if(hrtc->Instance==RTC)
   {
   /* USER CODE BEGIN RTC_MspInit 0 */
@@ -126,10 +125,8 @@ void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc)
 * @param hrtc: RTC handle pointer
 * @retval None
 */
-
 void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc)
 {
-
   if(hrtc->Instance==RTC)
   {
   /* USER CODE BEGIN RTC_MspDeInit 0 */
@@ -144,6 +141,259 @@ void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc)
 
 }
 
+/**
+* @brief SPI MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hspi: SPI handle pointer
+* @retval None
+*/
+void HAL_SPI_MspInit(SPI_HandleTypeDef* hspi)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(hspi->Instance==SPI1)
+  {
+  /* USER CODE BEGIN SPI1_MspInit 0 */
+
+  /* USER CODE END SPI1_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_SPI1_CLK_ENABLE();
+  
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    /**SPI1 GPIO Configuration    
+    PA5     ------> SPI1_SCK
+    PA6     ------> SPI1_MISO
+    PA7     ------> SPI1_MOSI 
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF5_SPI1;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN SPI1_MspInit 1 */
+
+  /* USER CODE END SPI1_MspInit 1 */
+  }
+  else if(hspi->Instance==SPI2)
+  {
+  /* USER CODE BEGIN SPI2_MspInit 0 */
+
+  /* USER CODE END SPI2_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_SPI2_CLK_ENABLE();
+  
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    __HAL_RCC_GPIOB_CLK_ENABLE();
+    /**SPI2 GPIO Configuration    
+    PC2     ------> SPI2_MISO
+    PC3     ------> SPI2_MOSI
+    PB10     ------> SPI2_SCK 
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF5_SPI2;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_10;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF5_SPI2;
+    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN SPI2_MspInit 1 */
+
+  /* USER CODE END SPI2_MspInit 1 */
+  }
+  else if(hspi->Instance==SPI3)
+  {
+  /* USER CODE BEGIN SPI3_MspInit 0 */
+
+  /* USER CODE END SPI3_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_SPI3_CLK_ENABLE();
+  
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    /**SPI3 GPIO Configuration    
+    PC10     ------> SPI3_SCK
+    PC11     ------> SPI3_MISO
+    PC12     ------> SPI3_MOSI 
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF6_SPI3;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN SPI3_MspInit 1 */
+
+  /* USER CODE END SPI3_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief SPI MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hspi: SPI handle pointer
+* @retval None
+*/
+void HAL_SPI_MspDeInit(SPI_HandleTypeDef* hspi)
+{
+  if(hspi->Instance==SPI1)
+  {
+  /* USER CODE BEGIN SPI1_MspDeInit 0 */
+
+  /* USER CODE END SPI1_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_SPI1_CLK_DISABLE();
+  
+    /**SPI1 GPIO Configuration    
+    PA5     ------> SPI1_SCK
+    PA6     ------> SPI1_MISO
+    PA7     ------> SPI1_MOSI 
+    */
+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7);
+
+  /* USER CODE BEGIN SPI1_MspDeInit 1 */
+
+  /* USER CODE END SPI1_MspDeInit 1 */
+  }
+  else if(hspi->Instance==SPI2)
+  {
+  /* USER CODE BEGIN SPI2_MspDeInit 0 */
+
+  /* USER CODE END SPI2_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_SPI2_CLK_DISABLE();
+  
+    /**SPI2 GPIO Configuration    
+    PC2     ------> SPI2_MISO
+    PC3     ------> SPI2_MOSI
+    PB10     ------> SPI2_SCK 
+    */
+    HAL_GPIO_DeInit(GPIOC, GPIO_PIN_2|GPIO_PIN_3);
+
+    HAL_GPIO_DeInit(GPIOB, GPIO_PIN_10);
+
+  /* USER CODE BEGIN SPI2_MspDeInit 1 */
+
+  /* USER CODE END SPI2_MspDeInit 1 */
+  }
+  else if(hspi->Instance==SPI3)
+  {
+  /* USER CODE BEGIN SPI3_MspDeInit 0 */
+
+  /* USER CODE END SPI3_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_SPI3_CLK_DISABLE();
+  
+    /**SPI3 GPIO Configuration    
+    PC10     ------> SPI3_SCK
+    PC11     ------> SPI3_MISO
+    PC12     ------> SPI3_MOSI 
+    */
+    HAL_GPIO_DeInit(GPIOC, GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12);
+
+  /* USER CODE BEGIN SPI3_MspDeInit 1 */
+
+  /* USER CODE END SPI3_MspDeInit 1 */
+  }
+
+}
+
+/**
+* @brief TIM_Base MSP Initialization
+* This function configures the hardware resources used in this example
+* @param htim_base: TIM_Base handle pointer
+* @retval None
+*/
+void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
+{
+  if(htim_base->Instance==TIM15)
+  {
+  /* USER CODE BEGIN TIM15_MspInit 0 */
+
+  /* USER CODE END TIM15_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_TIM15_CLK_ENABLE();
+  /* USER CODE BEGIN TIM15_MspInit 1 */
+
+  /* USER CODE END TIM15_MspInit 1 */
+  }
+  else if(htim_base->Instance==TIM16)
+  {
+  /* USER CODE BEGIN TIM16_MspInit 0 */
+
+  /* USER CODE END TIM16_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_TIM16_CLK_ENABLE();
+  /* USER CODE BEGIN TIM16_MspInit 1 */
+
+  /* USER CODE END TIM16_MspInit 1 */
+  }
+  else if(htim_base->Instance==TIM17)
+  {
+  /* USER CODE BEGIN TIM17_MspInit 0 */
+
+  /* USER CODE END TIM17_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_TIM17_CLK_ENABLE();
+  /* USER CODE BEGIN TIM17_MspInit 1 */
+
+  /* USER CODE END TIM17_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief TIM_Base MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param htim_base: TIM_Base handle pointer
+* @retval None
+*/
+void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim_base)
+{
+  if(htim_base->Instance==TIM15)
+  {
+  /* USER CODE BEGIN TIM15_MspDeInit 0 */
+
+  /* USER CODE END TIM15_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_TIM15_CLK_DISABLE();
+  /* USER CODE BEGIN TIM15_MspDeInit 1 */
+
+  /* USER CODE END TIM15_MspDeInit 1 */
+  }
+  else if(htim_base->Instance==TIM16)
+  {
+  /* USER CODE BEGIN TIM16_MspDeInit 0 */
+
+  /* USER CODE END TIM16_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_TIM16_CLK_DISABLE();
+  /* USER CODE BEGIN TIM16_MspDeInit 1 */
+
+  /* USER CODE END TIM16_MspDeInit 1 */
+  }
+  else if(htim_base->Instance==TIM17)
+  {
+  /* USER CODE BEGIN TIM17_MspDeInit 0 */
+
+  /* USER CODE END TIM17_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_TIM17_CLK_DISABLE();
+  /* USER CODE BEGIN TIM17_MspDeInit 1 */
+
+  /* USER CODE END TIM17_MspDeInit 1 */
+  }
+
+}
+
 /**
 * @brief UART MSP Initialization
 * This function configures the hardware resources used in this example
@@ -152,7 +402,6 @@ void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc)
 */
 void HAL_UART_MspInit(UART_HandleTypeDef* huart)
 {
-
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   if(huart->Instance==USART2)
   {
@@ -187,10 +436,8 @@ void HAL_UART_MspInit(UART_HandleTypeDef* huart)
 * @param huart: UART handle pointer
 * @retval None
 */
-
 void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
 {
-
   if(huart->Instance==USART2)
   {
   /* USER CODE BEGIN USART2_MspDeInit 0 */

bsp/stm32/stm32l476-st-nucleo/board/CubeMX_Config/Src/stm32l4xx_it.c

@@ -71,6 +71,7 @@
 /* USER CODE END 0 */
 
 /* External variables --------------------------------------------------------*/
+
 /* USER CODE BEGIN EV */
 
 /* USER CODE END EV */