| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119 |
- menu "Hardware Drivers Config"
- config SOC_STM32L496ZG
- bool
- select SOC_SERIES_STM32L4
- select RT_USING_COMPONENTS_INIT
- select RT_USING_USER_MAIN
- default y
- menu "Onboard Peripheral Drivers"
- config BSP_USING_STLINK_TO_USART
- bool "Enable STLINK TO USART (lpuart1)"
- select BSP_USING_UART
- select BSP_USING_LPUART1
- default y
- endmenu
- menu "On-chip Peripheral Drivers"
- config BSP_USING_GPIO
- bool "Enable GPIO"
- select RT_USING_PIN
- default y
- menuconfig BSP_USING_UART
- bool "Enable UART"
- default y
- select RT_USING_SERIAL
- if BSP_USING_UART
- config BSP_USING_UART1
- bool "Enable UART1"
- default n
- config BSP_UART1_RX_USING_DMA
- bool "Enable UART1 RX DMA"
- depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
- default n
- config BSP_USING_UART2
- bool "Enable UART2"
- default n
- config BSP_UART2_RX_USING_DMA
- bool "Enable UART2 RX DMA"
- depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
- default n
-
- config BSP_USING_LPUART1
- bool "Enable LPUART1"
- default n
- config BSP_LPUART1_RX_USING_DMA
- bool "Enable LPUART1 RX DMA"
- depends on BSP_USING_LPUART1 && RT_SERIAL_USING_DMA
- default n
- endif
-
- menuconfig BSP_USING_I2C
- bool "Enable I2C BUS"
- default n
- select RT_USING_I2C
- select RT_USING_I2C_BITOPS
- select RT_USING_PIN
- if BSP_USING_I2C
- menuconfig BSP_USING_I2C3
- bool "Enable I2C3 BUS"
- default y
- if BSP_USING_I2C3
- comment "Notice: PC0 --> 32; PC1 --> 33"
- config BSP_I2C3_SCL_PIN
- int "i2c3 scl pin number"
- range 1 176
- default 32
- config BSP_I2C3_SDA_PIN
- int "I2C3 sda pin number"
- range 1 176
- default 33
- endif
- menuconfig BSP_USING_I2C4
- bool "Enable I2C4 BUS"
- default n
- if BSP_USING_I2C4
- comment "Notice: PC1 --> 33; PD6 --> 54"
- config BSP_I2C4_SCL_PIN
- int "i2c4 scl pin number"
- range 1 176
- default 54
- config BSP_I2C4_SDA_PIN
- int "I2C4 sda pin number"
- range 1 176
- default 33
- endif
- endif
- config BSP_USING_ON_CHIP_FLASH
- bool "Enable on-chip FLASH"
- select RT_USING_FAL
- default n
-
- config BSP_USING_ON_CHIP_FLASH_FATFS
- bool "Enable onchip flash with FatFS"
- depends on BSP_USING_ON_CHIP_FLASH
- select RT_USING_DFS
- select RT_USING_DFS_ELMFAT
- default n
- config BSP_USING_USBD
- bool "Enable OTGFS as USB device"
- select RT_USING_USB_DEVICE
- default n
-
- source "../libraries/HAL_Drivers/Kconfig"
-
- endmenu
- endmenu
|
